LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2018 >> RX 350 Base, AWD >> Repair and Diagnosis >> Brakes >> Traction Control >> Brake Control System - Service Information >> Brake Actuator >> Installation [09/2015 - ] >> Procedure

Installation [09/2015 - ]: Procedure

  1. INSTALL BRAKE ACTUATOR ASSEMBLY 
    1. Install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts.
      Fig 1: Brake Actuator Tightening Sequence
      GTY613181Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 6.5 N.m (66 kgf/cm, 58 in.lbf) 

      NOTE:
      • Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.
      • Do not hold the brake actuator assembly by the connector.
      • Tighten the 3 bolts in the order shown in the illustration.
  2. INSTALL BRAKE ACTUATOR WITH BRACKET 
    1. Temporarily install the brake actuator with bracket with the bolt and 2 nuts.
      NOTE:
      • Do not damage the brake lines.
      • Do not hold the brake actuator assembly by the connector.

      HINT: 

      Install the brake actuator with bracket while avoiding the brake lines.

    2. Fully tighten the bolt and 2 nuts.

      Torque: 19 N.m (194 kgf/cm, 14 ft.lbf) 

    3. Temporarily tighten the 6 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.
      GTY650567Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a From 1st Chamber of Brake Master Cylinder Sub-assembly
      *b From 2nd Chamber of Brake Master Cylinder Sub-assembly
      *c To Front Wheel Cylinder Assembly RH
      *d To Rear Wheel Cylinder Assembly LH
      *e To Rear Wheel Cylinder Assembly RH
      *f To Front Wheel Cylinder Assembly LH
    4. Using a union nut wrench, fully tighten each brake line.

      Specified tightening torque (A) 

      Torque: 19.5 N.m (199 kgf/cm, 14 ft.lbf) 

      Specified tightening torque (B) 

      Torque: 15.2 N.m (155 kgf/cm, 11 ft.lbf) 

      GTY650504Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length
      *b Union Nut Wrench
      NOTE:
      • Do not kink or damage the brake lines.
      • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [09/2015 - 12/2017] , or refer to PRECAUTION [12/2017 - 08/2019] , or refer to PRECAUTION [08/2019 - ]

      • When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

        (A): 17.36 N.m (177 kgf/cm, 13 ft.lbf)

      • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

        (B): 13.38 N.m (136 kgf/cm, 10 ft.lbf)

    5. Connect the connector to the brake actuator assembly and lock the lock lever.
      GTY635230Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Connect the connector
      Lock the lock lever
      NOTE:
      • Make sure that the connector is locked securely.
      • Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.
  3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [09/2015 - 08/2016] , or refer to INITIALIZATION [08/2016 - 12/2017] , or refer to INITIALIZATION [12/2017 - 08/2019] , or refer to INITIALIZATION [08/2019 - ]

  4. BLEED BRAKE SYSTEM 

    Refer to BLEEDING [09/2015 - 08/2019] , or refer to BLEEDING [08/2019 - ]

  5. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION AND STORE SYSTEM INFORMATION 

    Refer to CALIBRATION [09/2015 - 08/2019] , or refer to CALIBRATION [08/2019 - ]

  6. PERFORM TEST MODE INSPECTION 

    Refer to TEST MODE PROCEDURE [09/2015 - 08/2019] , or refer to TEST MODE PROCEDURE [08/2019 - ]

  7. INSPECT BRAKE ACTUATOR USING TECHSTREAM 

    Refer to ON-VEHICLE INSPECTION [09/2015 - 08/2019] , or refer to ON-VEHICLE INSPECTION [08/2019 - ] 

  8. CHECK FOR AND CLEAR DTCS 

    Refer to DTC CHECK / CLEAR [09/2015 - 08/2019] , or refer to DTC CHECK / CLEAR [08/2019 - ]