LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2008 >> LS 460L >> Repair and Diagnosis >> Suspension >> Front Suspension >> Axle >> Rear Axle Hub >> Removal

Rear Axle Hub: Removal

HINT:

  1. REMOVE REAR WHEEL 
  2. REMOVE LOAD SENSING VALVE SENSOR BRACKET 
    1. Remove the bolt and load sensing valve sensor bracket from the toe control link sub-assembly.
      Fig 1: Locating Bolt And Load Sensing Valve Sensor Bracket
      G04944057Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. DISCONNECT REAR STABILIZER LINK ASSEMBLY LH 
    1. Remove the bolt and nut, and then disconnect the rear stabilizer link assembly LH from the rear No. 2 suspension arm assembly LH.
      Fig 2: Locating Bolt And Nut
      G04949531Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE REAR AXLE SHAFT LH NUT 
    1. Using SST and a hammer, release the staked part of the rear axle shaft LH nut.

      SST 09930-00010 

      NOTE: Release the staked part of the nut completely, otherwise the screw of the drive shaft may be damaged.
      Fig 3: Releasing Staked Part Of Rear Axle Shaft LH Nut
      G04944059Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. While applying the brakes, remove the rear axle shaft LH nut.
  5. DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH 
    1. Remove the 2 bolts and separate the rear disc brake caliper assembly.
      NOTE:
      • Hang the caliper with wire or equivalent.
      • Do not damage the brake hose.
      • Fig 4: Locating Bolts And Rear Disc Brake Caliper Assembly
        G05851040Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. DISCONNECT SPEED SENSOR REAR LH  (See REMOVAL )
  7. REMOVE REAR DISC  (See REMOVAL )
  8. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING  (See DISASSEMBLY )
  9. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING  (See DISASSEMBLY )
  10. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET LH  (See DISASSEMBLY )
  11. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY LH  (See DISASSEMBLY )
  12. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY LH  (See DISASSEMBLY )
  13. REMOVE PARKING BRAKE SHOE LEVER LH  (See DISASSEMBLY )
  14. DISCONNECT REAR SHOCK ABSORBER ASSEMBLY LH (for Coil suspension)  (See ON-VEHICLE INSPECTION )
  15. DISCONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH (for Air suspension)  (See ON-VEHICLE INSPECTION )
  16. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH 
    1. Using a plastic-faced hammer or equivalent, strike the part labeled A from the rear of the vehicle to maintain the clearance at the slide pin area.
      Fig 5: Identifying Arm, Slide Pin And Axle Carrier
      G04949505Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the nut, washer, bolt and No. 2 suspension arm from the axle carrier.
      Fig 6: Locating Nut, Washer, Bolt And No. 2 Suspension Arm
      G04949506Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the nut, rear suspension attachment sub-assembly, and rear No. 2 suspension toe adjust plate. Then remove the rear No. 2 suspension arm assembly.
  17. DISCONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH 
    1. Remove the nut from the rear No. 1 suspension arm.
    2. Fig 7: Locating Nut From Rear No. 1 Suspension Arm
      G04949507Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install 2 spacers (SST spacer B) onto the rear No. 1 suspension arm so that there is a space of approximately 1 mm between the arm and spacers.

      SST 09960-20010(09961-02060) 

      NOTE:
      • Make sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.
      • As SST may become damaged, make sure the space between the arm and spacers is not 1 mm or less.
        Fig 8: Disconnecting Rear No. 1 Suspension Arm From Axle Carrier
        G04949508Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using SST, disconnect the rear No. 1 suspension arm from the axle carrier.

      SST 09960-20010 (09961 -02010) 

      NOTE:
      • Do not damage the ball joint dust cover.
      • As the dust cover may be damaged, adjust SST with the center nut so that the body and crow are parallel.
      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
  18. DISCONNECT TOE CONTROL LINK SUB-ASSEMBLY LH 
    1. Remove the nut on the rear axle carrier side.
    2. Install 2 spacers (SST spacer B) onto the toe control link so that there is a space of approximately 1 mm between the arm and spacers.

      SST 09960-20010 (09961-02060) 

      NOTE:
      • Make sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.
      • As SST may become damaged, make sure the space between the arm and spacers is not 1 mm or less.
        Fig 9: Disconnecting Toe Control Link From Axle Carrier
        G04949517Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using SST, disconnect the toe control link from the axle carrier.

      SST 09960-20010(09961-02010) 

      NOTE:
      • Do not damage the ball joint dust cover.
      • As the dust cover may be damaged, adjust SST with the center nut so that the body and crow are parallel.
      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
  19. DISCONNECT REAR UPPER NO. 1 CONTROL ARM ASSEMBLY LH 
    1. Remove the nut on the rear axle carrier side.
    2. Install 2 spacers (SST spacer A) onto the rear upper No. 1 control arm so that there is a space of approximately 1 mm between the arm and spacers.

      SST 09960-20010(09961-02050) 

      NOTE:
      • Make sure to install the spacers (SST spacer A) as the steering knuckle spacer may shift.
      • As SST may become damaged, make sure the space between the arm and spacers is not 1 mm or less.
        Fig 10: Disconnecting Upper No. 1 Control Arm From Axle Carrier
        G04949493Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using SST, disconnect the upper No. 1 control arm from the axle carrier.

      SST 09960-20010 (09961-02010) 

      NOTE:
      • Do not damage the ball joint dust cover.
      • As the dust cover may be damaged, adjust SST with the center nut so that the body and crow are parallel.
      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
  20. DISCONNECT REAR UPPER NO. 2 CONTROL ARM ASSEMBLY LH 
    1. Remove the nut on the rear axle carrier side.
    2. Install 2 spacers (SST spacer A) onto the rear upper No. 2 control arm so that there is a space of approximately 1 mm between the arm and spacers.

      SST 09960-20010 (09961 -02050) 

      NOTE:
      • Make sure to install the spacers (SST spacer A) as the steering knuckle spacer may shift.
      • As SST may become damaged, make sure the space between the arm and spacers is not 1 mm or less.
        Fig 11: Disconnecting Upper No. 2 Control Arm From Axle Carrier
        G04949495Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using SST, disconnect the upper No. 2 control arm from the axle carrier.

      SST 09960-20010 (09961-02010) 

      NOTE:
      • Do not damage the ball joint dust cover.
      • As the dust cover may be damaged, adjust SST with the center nut so that the body and crow are parallel.
      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.
  21. REMOVE REAR AXLE ASSEMBLY LH 
    1. Using a plastic-faced hammer, separate the drive shaft from the rear axle carrier sub-assembly.
    2. Remove the rear axle assembly.
      NOTE:
      • Be careful not to damage the boots.
      • Use a wire or an equivalent to keep the rear drive shaft assembly from hanging down.
  22. REMOVE REAR NO. 1 WHEEL BEARING DUST DEFLECTOR LH 
    1. Using a screwdriver, remove the bearing dust deflector from the rear axle carrier.
      NOTE: Be careful not to dent or damage the axle carrier, as it is made of aluminum.
      Fig 12: Removing Bearing Dust Deflector From Rear Axle Carrier
      G04944068Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH 
    1. Hold the axle hub and bearing in a vise between aluminum plates.
      NOTE: Do not overtighten the vise.
    2. Remove the 4 bolts and axle hub and bearing from the rear axle carrier.
      Fig 13: Locating Bolts And Axle Hub And Bearing
      G04944069Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 2 nuts, parking brake anchor block, parking brake cable support bracket, and parking brake plate from the rear axle carrier.
    4. Fig 14: Locating Nuts, Parking Brake Anchor Block, Parking Brake Cable Support Bracket And Parking Brake Plate
      G04950030Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002