Inspection Procedure
HINT:
Check the condition of each related circuit connector before troubleshooting (See ELECTRONIC CIRCUIT INSPECTION PROCEDURE ).
- INSPECT TERMINAL VOLTAGE (DLC3 TC TERMINAL VOLTAGE)
- Turn the engine switch on (IG).
- Measure the voltage according to the value(s) in the table below.
Voltage
VOLTAGE SPECIFICATIONTester Connection Condition Specified Condition K16-13 (TC) - K16-4 (CG) Engine switch on (IG) 10 to 14 V - Turn the engine switch off.
- Measure the resistance according to the value(s) in the table below.
Resistance
RESISTANCE REFERENCE CHARTTester Connection Specified Condition K16-4 (CG) - Body ground Below 1 Ω
NG : Go to step 4
OK : Go to Next Step
- CHECK HARNESS AND CONNECTOR (ECM TO DLC3)
- Disconnect the ECM connector.
- Measure the resistance according to the value(s) in the table below.
Resistance
RESISTANCE REFERENCE CHARTTester Connection Specified Condition A7-3 (TC) - K16-13 (TC) Below 1 Ω K16-13 (TC) - Body ground 10 kΩ or higher
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR (TC TERMINAL CIRCUIT)
OK : Go to Next Step
- CHECK CAN COMMUNICATION SYSTEM
- Check if the CAN communication system DTC is output (See FAIL-SAFE CHART
).
Result
DTC RESULT REFERENCEResult Proceed to DTC is not output A DTC is not output (when troubleshooting accordance with the PROBLEM SYMPTOMS TABLE) B DTC is output C
B : PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
C : REPAIR CIRCUIT INDICATED BY OUTPUT CODE
A : REPLACE ABSORBER CONTROL ECU
- Check if the CAN communication system DTC is output (See FAIL-SAFE CHART
).
- CHECK HARNESS AND CONNECTOR (ECM TO DLC3)
- Disconnect the ECM connector.
- Measure the resistance according to the value(s) in the table below.
Resistance
RESISTANCE REFERENCE CHARTTester Connection Specified Condition A7-3 (TC) - K16-13 (TC) Below 1 Ω K16-13 (TC) - Body ground 10 kΩ or higher
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR (TC TERMINAL CIRCUIT)
OK : Go to Next Step
- CHECK HARNESS AND CONNECTOR (DLC3 TO BODY GROUND)
- Measure the resistance according to the value(s) in the table below.
Resistance
RESISTANCE REFERENCE CHARTTester Connection Specified Condition K16-4 (CG) - Body ground Below 1 Ω
NG : REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK : Go to Next Step
- Measure the resistance according to the value(s) in the table below.
- CHECK ECM (DLC3 TC TERMINAL INPUT)
- Using the SST, connect the terminals TC and CG of the DCL3.
SST 09843-18040
- Check that the engine, ABS, and VSC warning lights are blinking.
Result
DTC RESULT REFERENCEResult Proceed to Warning lights are blinking A Warning lights are not blinking B
B : REPLACE ECM
A : Go to Next Step
- Using the SST, connect the terminals TC and CG of the DCL3.
- CHECK CAN COMMUNICATION SYSTEM
- Check if the CAN communication system DTC is output (See FAIL-SAFE CHART
).
Result
DTC RESULT REFERENCEResult Proceed to DTC is not output A DTC is not output (when troubleshooting accordance with the PROBLEM SYMPTOMS TABLE) B DTC is output C
B : PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE
C : REPAIR CIRCUIT INDICATED BY OUTPUT CODE
A : REPLACE ABSORBER CONTROL ECU
- Check if the CAN communication system DTC is output (See FAIL-SAFE CHART
).