Terminals Of Ecu
- CHECK TRANSPONDER KEY ECU ASSEMBLY
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
- Disconnect the T27 ECU connector.
- Measure the resistance and voltage of the wire harness side connector.RESISTANCE AND VOLTAGE SPECIFICATIONS
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition GND (T27-14) - Body ground W-B - Body ground Ground Always Below 1 Ω +B (T27-1) - GND (T27-14) L-W - W-B Power source supply Always 10 to 14 V IG (T27-2) - GND (T27-14) B-R - W-B Ignition power supply Ignition switch ON 10 to 14 V Ignition switch OFF Below 1 V KSW (T27-10) - GND (T27-14) R-B - W-B Unlock warning switch No key in ignition key cylinder 10 kΩ or higher Key inserted Below 1 Ω CTY (T27-4) - GND (T27-14) R-Y - W-B Driver side courtesy switch Driver side door closed 10 kΩ or higher Driver side door open Below 1 Ω If the result is not as specified, there may be a malfunction on the wire harness side.
- Reconnect the T27 ECU connector.
- Measure the voltage of the connector.VOLTAGE SPECIFICATIONS
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition KSW(T27-10) - GND (T27-14) R-B - W-B Unlock warning switch No key in ignition key cylinder 10 to 14 V Key inserted Below 1 V VC5 (T27-8) - GND (T27-14) Y - W-B Power source of transponder key amplifier No key in ignition key cylinder Below 1 V Key inserted 4.6 to 5.4 V TXCT (T27-12) - GND (T27-14) V-G - W-B Transponder key amplifier communication signal No key in ignition key cylinder Below 1 V Key inserted Pulse generation (see 1 waveform 1) CODE (T27-11) - GND (T27-14) L-B - W-B Transponder key amplifier communication signal No key in ignition key cylinder Below 1 V Key inserted Pulse generation (see 2 waveform 2) EFIO (T27-6) - GND (T27-14) W - W-B ECM output signal Ignition switch OFF Below 1 V Ignition switch ON Pulse generation (see 3 waveform 3) EFII (T27-7) - GND (T27-14) Y - W-B ECM input signal Ignition switch OFF Below 1 V Ignition switch ON Pulse generation (see 4 waveform 4) IND (T27-3) - GND (T27-14) G-R - W-B Security indicator light signal Engine immobiliser system is unset Below 1 V Engine immobiliser system is set Pulse generation CTY (T27-4) - GND (T27-14) R-Y - W-B Driver side courtesy switch Driver side door closed 10 to 14 V Driver side door open Below 1 V If the result is not as specified, the ECU may have a malfunction
- Inspect using an oscilloscope.
- Waveform 1 (Reference)WAVEFORM 1 REFERENCE
Item Content Symbols (Terminal No.) TXCT (T27-12) - GND (T27-14) Tool Setting 5 V/DIV., 20 msec./DIV. Condition Key is inserted - Waveform 2 (Reference)WAVEFORM 2 REFERENCE
Item Content Symbols (Terminal No.) CODE (T27-11) - GND (T27-14) Tool Setting 5 V/DIV., 20 msec./DIV. Condition Key is inserted - Waveform 3 (Reference)WAVEFORM 3 REFERENCE
Item Content Symbols (Terminal No.) EFIO (T27-6) - GND (T27-14) Tool Setting 10 V/DIV., 50 msec./DIV. Condition Ignition switch ON - Waveform 4 (Reference)WAVEFORM 4 REFERENCE
Item Content Symbols (Terminal No.) EFII (T27-7) - GND (T27-14) Tool Setting 10 V/DIV., 50 msec./DIV. Condition Ignition switch ON
- Waveform 1 (Reference)
- CHECK ECM
- Measure the resistance and voltage of the connectors.RESISTANCE AND VOLTAGE SPECIFICATIONS
Symbols (Terminal No.) Wiring Color Terminal Description Condition Specified Condition E1 (E6-1) - Body ground BR- Body ground Ground Always Below 1 Ω BATT (E10-3) - E1 (E6-1) B-R - BR Battery (for measuring battery voltage and for ECM memory) Always 10 to 14 V +BM (E10-7) - E1 (E6-1) Y-B - BR Power source of ECM Ignition switch OFF Below 1 V Ignition switch ON 10 to 14 V +B (E10-1) - E1 (E6-1) B-Y - BR Power source of ECM Ignition switch OFF Below 1 V Ignition switch ON 10 to 14 V +B2 (E10-2) -E1 (E6-1) B-Y - BR Power source of ECM Ignition switch OFF Below 1 V Ignition switch ON 10 to 14 V IGSW (E10-9) - E1 (E6-1) B-R - BR Ignition power supply of ECM Ignition switch OFF Below 1 V Ignition switch ON 10 to 14 V IMI (E9-16) - E1 (E6-1) W - BR Transponder key ECU input signal Ignition switch OFF Below 1 V Ignition switch ON Pulse generation (see 1 waveform 1) IMO (E9-15) - E1 (E6-1) Y - BR Transponder key ECU output signal Ignition switch OFF Below 1 V Ignition switch ON Pulse generation (see 2 waveform 2) If the result is not as specified, the ECM may have a malfunction.
- Inspect using an oscilloscope.
- Waveform 1 (Reference)WAVEFORM 1 REFERENCE
Item Content Symbols (Terminal No.) IMI (E9-16) - E1 (E6-1) Tool Setting 10V/DIV., 50 msec./DIV. Condition Ignition switch ON - Waveform 2 (Reference)WAVEFORM 2 REFERENCE
Item Content Symbols (Terminal No.) IMO (E9-15) - E1 (E6-1) Tool Setting 10V/DIV., 50 msec./DIV. Condition Ignition switch ON
- Waveform 1 (Reference)
- Measure the resistance and voltage of the connectors.