LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2006 >> RX 400h AWD >> Repair and Diagnosis >> Brakes >> Brakes Control Systems >> Brake Control >> Electronically Controlled Brake System >> TC and CG Terminal Circuit >> Wiring Diagram

TC and CG Terminal Circuit: Wiring Diagram

Fig 1: TC And CG Terminal Circuit - Wiring Diagram
G04113281Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NOTE: When replacing the skid control ECU, perform INITIALIZATION  of linear solenoid valve and calibration .
  1. INSPECT DLC3 (TC AND CG TERMINAL) 
    1. Turn the ignition switch on.
    2. Measure the voltage according to the value(s) in the table below.

      Voltage 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Condition Specified Condition
      D1-13 (TC) - Body ground Ignition switch on 10 to 14 V
    3. Measure the resistance according to the value(s) in the table below.

      Resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      D1-4 (CG) - Body ground Below 1 Ω
      Fig 2: Connecting Terminals TC And CG Of DLC3
      G04113282Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG : Go to step   3 

    OK : GO TO NEXT STEP 

  2. CHECK CAN COMMUNICATION SYSTEM 
    1. Check if the CAN communication DTC is output (See HOW TO PROCEED WITH TROUBLESHOOTING ).

      Result 

      RESULT REFERENCE

      Condition Proceed to
      DTC is not output A
      DTC is output B

      HINT:

      If troubleshooting has been carried out according to the PROBLEM SYMPTOMS TABLE, refer back to the table and proceed to the next step before replacing the part (See PROBLEM SYMPTOMS TABLE  ).

    B : REPAIR CIRCUIT INDICATED BY OUTPUT CODE 

    A : GO TO NEXT STEP 

  3. CHECK HARNESS AND CONNECTOR (DLC3 (TC) TO HV CONTROL ECU) 
    1. Disconnect the HV control ECU connector.
    2. Measure the resistance according to the value(s) in the table below.

      Resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      D1-13 (TC) - H29-3 (TC) Below 1 Ω
    3. Measure the resistance according to the value(s) in the table below.

      Resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      D1-13 (TC) - Body ground 10 kΩ or higher
      Fig 3: Disconnecting HV Control ECU Connector
      G04113283Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG : REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK : GO TO NEXT STEP 

  4. CHECK HARNESS AND CONNECTOR (DLC3 (CG) TO BODY GROUND) 
    1. Measure the resistance according to the value(s) in the table below.

      Resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      D1-4 (CG) - Body ground Below 1 Ω
      Fig 4: Checking Harness And Connector (DLC3 (CG) To Body Ground)
      G04113284Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG : REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK : GO TO NEXT STEP 

  5. CHECK ECM (DLC3 (TC) INPUT) 

    SST 09843-18040 

    1. Using the SST, connect terminals TC and CG of the DLC3.
    2. Check that the engine warning light is blinking.

      Result 

      RESULT REFERENCE

      Condition Proceed to
      Engine warning light is blinking A
      Engine warning light is not blinking B
      Fig 5: Connecting Terminals TC And CG Of DLC3
      G04113285Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    B : REPAIR OR REPLACE HARNESS OR CONNECTOR 

    A : GO TO NEXT STEP 

  6. CHECK CAN COMMUNICATION SYSTEM 
    1. Check if the CAN communication DTC is output (See HOW TO PROCEED WITH TROUBLESHOOTING ).

      Result 

      RESULT REFERENCE

      Condition Proceed to
      DTC is not output A
      DTC is output B

      HINT:

      If troubleshooting has been carried out according to the PROBLEM SYMPTOMS TABLE, refer back to the table and proceed to the next step before replacing the part (See PROBLEM SYMPTOMS TABLE  ).

    B : REPAIR CIRCUIT INDICATED BY OUTPUT CODE 

    A : REPLACE SKID CONTROL ECU