LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2006 >> RX 400h AWD >> Repair and Diagnosis >> Brakes >> Brakes Control Systems >> Brake Control >> Electronically Controlled Brake System >> DTC C1249/49 Open in Stop Light Switch Circuit >> Wiring Diagram

DTC C1249/49 Open in Stop Light Switch Circuit: Wiring Diagram

Fig 1: Open In Stop Light Switch Circuit - Wiring Diagram
G04113223Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NOTE: When replacing the skid control ECU, perform INITIALIZATION  of linear solenoid valve and calibration .
  1. CHECK STOP LIGHT SWITCH OPERATION 
    1. Check that the stop light comes on when the brake pedal is depressed and turns off when the brake pedal is released.
      STOP LIGHT SWITCH CONDITION

      Condition Illumination Condition
      Brake pedal depressed ON
      Brake pedal released OFF

      HINT:

      Check the stop light bulb as it may have burnt out.

    NG : REPAIR STOP LIGHT CIRCUIT 

    OK : GO TO NEXT STEP 

  2. CHECK HARNESS AND CONNECTOR (BETWEEN SKID CONTROL ECU AND STOP LIGHT SWITCH) 
    1. Disconnect the stop light switch connector and skid control ECU connector.
    2. Measure the resistance according to the value(s) in the table below.

      Resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      S39-14 (STP) - S13-1 Below 1 Ω
      Fig 2: Disconnecting Stop Light Switch Connector And Skid Control ECU Connector
      G04113224Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG : REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK : GO TO NEXT STEP 

  3. INSPECT SKID CONTROL ECU (GND TERMINAL) 
    1. Connect the skid control ECU connector.
    2. Measure the resistance according to the value(s) in the table below.

      Resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      S38-1 (GND1) - Body ground Below 1 Ω
      S39-2 (GND2) - Body ground Below 1 Ω
      S39-1 (GND3) - Body ground Below 1 Ω
      S40-2 (GND4) - Body ground Below 1 Ω
      S40-1 (GND5) - Body ground Below 1 Ω
      S41-4 (GND6) - Body ground Below 1 Ω
      Fig 3: Inspecting Skid Control ECU (GND Terminal)
      G04113225Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG : REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK : GO TO NEXT STEP 

  4. INSPECT STOP LIGHT SWITCH ASSEMBLY 
    1. Disconnect the stop light switch assembly connector.
    2. Measure the resistance according to the value(s) in the table below.

      Resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Switch Condition Tester Connection Specified Condition
      Switch pin free 1 - 2 Below 1 Ω
      Switch pin pushed in 1 - 2 10 kΩ or higher
      Fig 4: Disconnecting Stop Light Switch Assembly Connector
      G04113226Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG : REPLACE STOP LIGHT SWITCH ASSEMBLY 

    OK : GO TO NEXT STEP 

  5. RECONFIRM DTC 
    1. Clear the DTC (See DTC CHECK / CLEAR  ).
    2. Turn the ignition switch on.
    3. Depress the brake pedal several times to test the stop light circuit.
    4. Check that the same DTC is recorded (See DTC CHECK / CLEAR  ).

      HINT:

      Reinstall the sensors, connectors, etc. and store the previous vehicle conditions before rechecking for DTCs.

      Result 

      RESULT REFERENCE

      Condition Proceed to
      DTC is not output A
      DTC is output B

    B : REPLACE SKID CONTROL ECU 

    A : END