Engine (V8 5.0L Petrol): Specifications
WARNING: This page is about a different car, the 2013 Land Rover LR4, 2012 Land Rover LR4, 2011 Land Rover LR4, and 2010 Land Rover LR4. However, it is still accessible from the selected car via links, so may be relevant.
Engine Data
| Engine Description | Engine Capacity | Maximum Engine Torque (EEC) | Maximum Engine Power (EEC) | Compression Ratio | Bore | Stroke |
|---|---|---|---|---|---|---|
| 90° "Vee" 8 Cylinder 32 Valves | 4.999 ccm | 510 Nm at 3.500 RPM | 276 kW at 6.500 RPM | 11.5 ± 0.5 | 92.5 mm | 93 mm |
Engine Firing Order
| Firing Order |
|---|
| 1:2:7:3:4:5:6:8 |
Engine Valve Clearance (cold)
| Intake Valve | Exhaust Valve |
|---|---|
| N/A | 0.25 mm ± 0.02 |
Spark Plugs
| Specification | Spark Plug Gap |
|---|---|
| ILKR6C-10 | 1 mm |
Lubricants, Fluids, Sealers and Adhesives
| Description | Specification |
|---|---|
| Engine Oil | WSS-M2C925-A |
| Sealant | WSE-M4G323-A6 |
| Core plug and stub pipe retainer | WSK-M2G349-A7 |
Capacities
| Description | Liters |
|---|---|
| Engine oil, initial fill | 9.5 |
| Engine oil, service fill with oil filter change | 8.0 |
Cylinder Head and Valve Train
| Item | Specification |
|---|---|
| Cylinder head maximum permitted warp (mm) (flatnes specfication) | |
| overall | 0.08 |
| over 150x150 mm area | 0.05 |
| over 25x25 mm area | 0.02 |
| Valve guide inner diameter (mm) | 5.51 ± 0.01 |
| Intake valve effective length (mm) (tip to gauge line) | 97.63 ± 0.1 |
| Exhaust valve effective length (mm) (tip to gauge line) | 94.39 ± 0.1 |
| Valve stem to guide clearance intake diametrical (mm) | 0.022 - 0.057 |
| Valve stem to guide clearance exhaust diametrical (mm) | 0.03 - 0.065 |
| Valve head diameter intake (mm) | 36 ± 0.1 |
| Valve head diameter exhaust (mm) | 30 ± 0.1 |
| Intake valve face angle (degrees) | 44.875 ± 0.125 |
| Exhaust valve face angle (degrees) | 44.875 ± 0.125 |
| Valve stem diameter intake (mm) | 5.4705 ± 0.0075 |
| Valve stem diameter exhaust (mm) | 5.4625 ± 0.0075 |
| Valve spring free length (mm) - inlet | 43.43 |
| Valve spring free length (mm) - exhaust | 46.1 |
| Valve spring installed height (mm) - inlet | 34.49 |
| Valve spring installed height (mm) - exhaust | 35.1 |
| Camshaft lobe lift intake (mm) | 5.5 (low) 10.53 (high) |
| Camshaft lobe lift exhaust (mm) | 9.36 |
| Camshaft journal to cylinder head bearing surface clearance diametrical (mm) | 0.025 - 0.065 |
| Camshaft journal diameter - all positions | 26.965 ± 0.01 |
| Bearing diameter - all positions | 27.01 ± 0.01 |
| Camshaft journal maximum run out limit (mm) | |
| Camshaft journals to end journals | 0.03 |
| Camshaft journals to adjacent journals | 0.015 |
| Camshaft journal maximum out of round (mm) - all journals | 0.005 |
Torque Specifications
NOTE:
A = Refer to procedure for correct torque sequence.
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| Engine cover mounting bolts | 10 | 7 | - |
| Accessory drive belt tensioner retaining bolt | 40 | 30 | - |
| Supercharger belt idler/tensioner bracket retaining bolts | 25 | 18 | - |
| Secondary drive belt idler retaining bolts | 40 | 30 | - |
| Power steering pump pulley retaining bolts | 25 | 18 | - |
| Power steering pump retaining bolts | 25 | 18 | - |
| Power steering pump bracket to engine retaining bolts | 25 | 18 | - |
| Generator retaining bolts | 48 | 35 | - |
| Starter motor retaining bolts | 40 | 30 | - |
| Air conditioning compressor retaining bolts | 25 | 18 | - |
| Engine mounting to engine mounting bracket retaining nuts | 100 | 74 | - |
| Engine mounting to subframe retaining bolts | 56 | 41 | - |
| Engine mounting bracket to engine retaining bolts | 45 + 60° | 33 + 60° | - |
| Crankshaft damper pulley retaining LH threaded bolt | 200 + 270° | 148 + 180° | - |
| Flexplate retaining bolts | 45 + 90° | 33 + 90° | - |
| Exhaust manifold heat shield retaining bolts | A | - | - |
| Exhaust manifold retaining bolts | A | - | - |
| Engine wiring harness bracket retaining bolts | 10 | 7 | - |
| Coolant outlet pipe | 10 | 7 | - |
| Intercooler retaining bolts | 25 | 18 | - |
| Intake manifold retaining bolts | 25 | 18 | - |
| Oil Cooler retaining bolts | 13 | 10 | - |
| Knock sensor (KS) retaining bolt | 20 | 14 | - |
| Ignition coil retaining bolts | 8 | - | 71 |
| Spark plugs | 20 | 15 | - |
| Fuel rail retaining bolts | A | - | - |
| High pressure fuel pipe retaining bolts | A | - | - |
| High pressure fuel pump retaining bolts | 12 | 9 | - |
| Oil filter housing assembly retaining bolts | 12 | 9 | - |
| Oil filter cap | 25 | 18 | - |
| Lifting eye bolts | 25 + 90° | 18 + 90° | - |
| Manifold absolute pressure and temperature (MAPT) sensor retaining bolts | 5 | - | 44 |
| Coolant pump retaining bolts | 12 | 9 | - |
| Variable valve timing (VVT) oil control solenoid retaining bolts | 10 | 7 | - |
| Camshaft position (CMP) sensor retaining bolts | 10 | 7 | - |
| Camshaft cover retaining bolts | 13 | 10 | - |
| Front upper timing cover retaining bolts | 12 | 9 | - |
| Front lower timing cover retaining bolts | A | - | - |
| Engine rear cover retaining bolts | A | - | - |
| VVT to camshaft retaining bolts | 32 | 24 | - |
| Camshaft bearing caps retaining bolts | 11 | 8 | - |
| Primary timing chain fixed guide retaining bolts | 12 | 9 | - |
| Primary timing chain tensioner retaining bolts | 12 | 9 | - |
| Primary timing chain tensioner guide blade retaining bolts | 25 | 18 | - |
| Auxiliary chain tensioner guide retaining bolts | 21 | 15 | - |
| Auxiliary chain fixed guide retaining bolt | 12 | 9 | - |
| Oil pump sprocket retaining bolt | 21 | 15 | - |
| Cylinder head retaining bolts | A | - | - |
| Engine oil level (EOL) sensor retaining bolt | 12 | 9 | - |
| Crankshaft position (CKP) sensor retaining bolt | 10 | 7 | - |
| Oil sump body to engine retaining bolts | 25 | 18 | - |
| Oil pan drain plug | 24 | 18 | - |
| Oil transfer tube to Oil pan body retaining bolts | 11 | 8 | - |
| Oil pump to engine block retaining bolts | 25 | 18 | - |
| Pick-up pipe to oil pump retaining bolts | 12 | 9 | - |
| Windage tray retaining bolts | 25 | 18 | - |
| Piston cooling jet retaining bolts | 12 | 9 | - |
| Engine block coolant draining plug | 50 | 37 | - |
| Cooling fan pulley | 25 | 18 | - |
| Connecting Rod Bolts | |||
| Stage 1 | 10 | 7 | - |
| Stage 2 | 50 | 37 | - |
| Main Bearing Cap | |||
| M10 bolt stage 1 | 25 | 18 | - |
| M10 bolt stage 2 | 57 + 70° | 42 + 70° | - |
| M8 bolt stage 1 | 15 | 11 | - |
| M8 bolt stage 2 | 33 + 75° | 24 + 75° | - |