LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2019 >> Stinger GTS, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 7 (Engine Cooling System - 2.0L) >> Water Temperature Control Assembly >> Repair Procedures >> Removal And Installation

Removal And Installation

WARNING: This page is about a different variant/trim than selected.
  1. Disconnect the battery negative terminal.
  2. Remove the engine cover.

    (Refer to Engine and Transmission Assembly - " ENGINE COVER  ") 

  3. Remove the engine room front under cover.

    (Refer to Engine and Transmission Assembly - " ENGINE ROOM UNDER COVER  ") 

  4. Drain the coolant.

    (Refer to Cooling System - " COOLANT  ") 

  5. Remove the RH hood sealing cover (A).
    G12789641Courtesy of KIA MOTORS AMERICA, INC.
  6. Remove the engine room cover (A).
    G12789642Courtesy of KIA MOTORS AMERICA, INC.
  7. Remove the LH hood sealing cover (A).
    G12789643Courtesy of KIA MOTORS AMERICA, INC.
  8. Remove the cowl top cover.

    (Refer to Body (Interior and Exterior) -" COWL TOP COVER  ") 

  9. Disconnect the wiring connector and harness from the engine room.
    1. Remove the fuse box cover (A).
      G12789644Courtesy of KIA MOTORS AMERICA, INC.
    2. Disconnect the front control connector (A).
    3. Disconnect the starter motor ground cable (B).

      Tightening torque: 

      7.8 - 9.8 N.m (0.8 - 1.0 kgf.m, 5.8 - 7.2 lb.ft)

    4. Disconnect the alternator ground cable (C).

      Tightening torque: 

      7.8 - 9.8 N.m (0.8 - 1.0 kgf.m, 5.8 - 7.2 lb.ft)

    5. Remove the wiring protector (D).

      Tightening torque: 

      4.9 - 7.8 N.m (0.5 - 0.8 kgf.m, 3.6 - 5.8 lb.ft. 43.4 - 69.4 lb.in)

      G12789645Courtesy of KIA MOTORS AMERICA, INC.

      Information 

      When remove the protector from the fuse box, push the protector fixing clip (A) in the direction of the arrow and then remove the protector.

      G12789646Courtesy of KIA MOTORS AMERICA, INC.
    6. Disconnect the ECM connector (A) and TCM connector (B).
    7. Remove the wiring protector (C).

      Tightening torque: 

      4.9 - 7.8 N.m (0.5 - 0.8 kgf.m, 3.6 - 5.8 lb.ft. 43.4 - 69.4 lb.in)

    G12789647Courtesy of KIA MOTORS AMERICA, INC.
  10. Disconnect the heater hoses (A).
    G12789648Courtesy of KIA MOTORS AMERICA, INC.
  11. Disconnect the radiator upper hose (A).
    G12789649Courtesy of KIA MOTORS AMERICA, INC.
  12. Remove the engine room panel (A).
    G12789650Courtesy of KIA MOTORS AMERICA, INC.
  13. Remove the water outlet pipe (A).

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12789651Courtesy of KIA MOTORS AMERICA, INC.
  14. Disconnect the wiring connectors and harness clamps and remove the wiring protector around the water temperature control assembly.
    G12789652Courtesy of KIA MOTORS AMERICA, INC.
  15. Disconnect the bypass hose (A).
    G12789653Courtesy of KIA MOTORS AMERICA, INC.
  16. Disconnect the oil cooler hose (A) and electric throttle body control (ETC) module water hose (B).
    G12789654Courtesy of KIA MOTORS AMERICA, INC.
  17. Remove the water temperature control assembly (A) with gasket.

    Tightening torque: 

    Bolts:

    14.7 - 19.6 N.m (1.5 - 2.0 kgf.m, 10.8 - 14.5 lb.ft)

    Nuts:

    19.6 - 23.5 N.m (2.0 - 2.4 kgf.m, 14.5 - 17.4 lb.ft)

    G12789655Courtesy of KIA MOTORS AMERICA, INC.
    G12789656Courtesy of KIA MOTORS AMERICA, INC.
    NOTE: Always use a new water temperature control assembly gasket.
  18. Install the other parts in the reverse order of removal.
  19. Fill the coolant.

    (Refer to Cooling system - " COOLANT  ") 

  20. Start engine and check for leaks.
  21. Recheck engine coolant level.