LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2019 >> Stinger GTS, AWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 12 (Timing System - 2.0L) >> Timing Chain Cover >> Repair procedures >> Installation

Repair procedures: Installation

WARNING: This page is about a different variant/trim than selected.
  1. Install the timing chain cover.
    1. Using a gasket scraper, remove all the old packing material from the gasket surfaces.
    2. The sealant locations on chain cover and on counter parts (cylinder head, cylinder block, and ladder frame) must be free of engine oil and etc.
    3. Before assembling the timing chain cover, liquid sealant Loctite 5900H or equivalent should be applied on the gap between camshaft front bearing cap, cylinder head and cylinder block. The part must be assembled within 5 minutes after sealant was applied.

      Bead width:  2.0 - 3.0 mm (0.08 - 0.12 in.)

      G12791918Courtesy of KIA MOTORS AMERICA, INC.
    4. After applying liquid sealant Loctite 5900H or equivalent on the timing chain cover.

      The part must be assembled within 5 minutes after sealant was applied. Continuous bead of sealant should be applied to prevent any path of oil leakage.

      Bead width:  2.0 - 3.0 mm (0.08 - 0.12 in.)

      G12791919Courtesy of KIA MOTORS AMERICA, INC.
    5. The dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover to be in exact position.

      Tightening torque 

      M6 X 25 bolt:

      9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

      M8 X 28 bolt:

      18.6 - 22.6 N.m (1.9 - 2.3 kgf.m, 13.7 - 16.6 lb.ft)

      G12791920Courtesy of KIA MOTORS AMERICA, INC.
      NOTE: The engine starting or pressure tests should not be performed within 30 minutes after the timing chain cover was assembled.
  2. Install the front oil seal.

    (Refer to Timing System - " FRONT OIL SEAL  ") 

  3. Install the drive belt tensioner.

    (Refer to Drive Belt System - " DRIVE BELT TENSIONER  ") 

  4. Remove it by breaking the center of E-CVVT motor plug (A).
    G12791921Courtesy of KIA MOTORS AMERICA, INC.
    NOTE:
    • Remove after 30 minutes of switching "OFF" the ignition to drain out the oil inside the E-CVVT motor plug.
    • Do not tilt the front of engine (timing chain cover side) downward as residual oil may flow out during E-CVVT motor plug removal.
    • If oil flows out during E-CVVT motor plug removal, wipe off immediately and block the motor shaft inlet with a clean towel.
  5. Clean the E-CVVT motor plug mounting surface (A) with oil cleaner.
    G12791922Courtesy of KIA MOTORS AMERICA, INC.
    NOTE:
    • If the surface is not cleaned, E-CVVT motor plug may be separated due to diminished separation force from residual oil.
    • When spraying oil cleaner, block around the motor shaft inlet and rotor gap with a clean towel to prevent inflow of oil from flowing into the rotor gap.
  6. When reusing the E-CVVT cover, inspect the below items.
    1. If there is sign of leakage from inside the E-CVVT cover, replace it with a new one.
    2. Check for worn connector brush.

      Specification:  Over 5 mm (0.1969 in.)

      G12791923Courtesy of KIA MOTORS AMERICA, INC.

      If measurement is below specification, replace the E-CVVT cover with a new one.

    3. Check for damaged oil seal (A) and replace any damaged E-CVVT cover with a new one.
      G12791924Courtesy of KIA MOTORS AMERICA, INC.
    4. After inspecting E-CVVT, if no problem is found, replace the o-ring (A) with a new one.
    G12791925Courtesy of KIA MOTORS AMERICA, INC.
  7. Install the E-CVVT cover.
    1. Apply engine oil on oil seal lip (A).
      G12791926Courtesy of KIA MOTORS AMERICA, INC.
      NOTE: When applying oil, keep the connector brush (A) clean from foreign materials.
      G12791927Courtesy of KIA MOTORS AMERICA, INC.
    2. Insert SST (09243-C2000) into the E-CVVT motor shaft.
      G12791928Courtesy of KIA MOTORS AMERICA, INC.
      NOTE: Correctly mount SST onto the motor shaft.
    3. Slowly push the E-CVVT cover (A) until it is flush with the timing chain cover surface.
      G12791929Courtesy of KIA MOTORS AMERICA, INC.
      NOTE: Installing the E-CVVT cover without SST may cause oil leakage inside the E-CVVT motor due to damaged or separated E-CVVT oil seal.
    4. Pre-tighten the bolts in the below sequence, and then remove the SST (09243-C2000).

      Tightening torque: 

      1.0 - 2.0 N.m (0.1 - 0.2 kgf.m, 0.7 - 1.4 lb.ft)

      Fig 1: E-CVVT Cover Bolts Pre-Tightening Sequence
      G12791930Courtesy of KIA MOTORS AMERICA, INC.
    5. Tighten the bolts to the specified torque in the sequence below.

      Tightening torque: 

      9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

      Fig 2: E-CVVT Cover Bolts Tightening Sequence
      G12791931Courtesy of KIA MOTORS AMERICA, INC.
  8. Install the E-CVVT plug.
    1. By using SST (09243-C2000), insert the plug (A) into the E-CVVT cover hole.
      G12791932Courtesy of KIA MOTORS AMERICA, INC.
      NOTE: Do not reuse a E-CVVT motor plug.
    2. Mount the stopper of SST so that it sits at the end of E-CVVT motor shaft.
    G12791933Courtesy of KIA MOTORS AMERICA, INC.
  9. Inspect the pressed depth of E-CVVT plug.
    1. By using a steel ruler, measure the distance from E-CVVT cover center boss to the end of motor shaft (1).
    2. By using a steel ruler, measure the distance from E-CVVT cover center boss to the end of E-CVVT plug (2).
      G12791934Courtesy of KIA MOTORS AMERICA, INC.
    3. Calculate the pressed depth (3) of motor plug.

      If out of specification, reinstall after replacing the E-CVVT plug with a new one.

      Pressed depth:  (3) = (2) - (1)

      Specification:  1.9 - 2.1 mm (0.0748 - 0.0827 in.)

  10. Insert the E-CVVT cover plug so that the protrusion (A) reach to E-CVVT cover groove correctly.
    G12791935Courtesy of KIA MOTORS AMERICA, INC.
    G12791936Courtesy of KIA MOTORS AMERICA, INC.
    • Check how much protrude after installing the E-CVVT plug.
      G12791937Courtesy of KIA MOTORS AMERICA, INC.
    • Be careful that the plug is not inserted inside E-CVVT cover beyond the regulated range.
  11. Install the other parts in the reverse order of removal.
    NOTE:
    • Refill engine with engine oil.
    • Refill a transaxle with fluid.
    • Refill a radiator and a reservoir tank with engine coolant.
    • Clean battery posts and cable terminals and assemble.
    • Inspect for fuel leakage.
      • After assemble the fuel line, turn on the ignition switch (do not operate the starter) so that the fuel pump runs for approximately two seconds and fuel line pressurizes.
      • Repeat this operation two or three times, then check for fuel leakage at any point in the fuel line.
    • Refill radiator and reservoir tank with engine coolant.
    • Bleed air from the cooling system.