LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2019 >> Stinger GTS, AWD >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Intake And Exhaust System 3.3L >> Turbo Manifold Module And Catalytic Converter >> Repair Procedures >> Removal And Installation >> RH Turbo Manifold Module

RH Turbo Manifold Module

  1. Remove the engine and transmission assembly.

    (Refer to " ENGINE AND TRANSMISSION ASSEMBLY  ") 

  2. Disconnect the RH electric waste gate actuator (EWGA) connector (A).
    G12803049Courtesy of KIA MOTORS AMERICA, INC.
  3. Remove the RH turbo manifold module heat protector (A).

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12803050Courtesy of KIA MOTORS AMERICA, INC.
  4. Disconnect the RH turbocharger water hose (A).
    G12803051Courtesy of KIA MOTORS AMERICA, INC.
  5. Disconnect the electric throttle control (ETC) module water hose (A).
    G12803052Courtesy of KIA MOTORS AMERICA, INC.
  6. Disconnect the oil cooler water hose B (A).
    G12803053Courtesy of KIA MOTORS AMERICA, INC.
  7. Remove the RH turbocharger water hose & pipe (A)

    Tightening torque 

    Eye bolts:

    33.3 - 39.2 N.m (3.4 - 4.0 kgf.m, 26.6 - 28.9 lb.ft)

    Bolt:

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12803054Courtesy of KIA MOTORS AMERICA, INC.
  8. Remove the water inlet pipe (A).

    Tightening torque: 

    24.5 - 28.4 N.m (2.5 - 2.9 kgf.m, 18.1 - 21.0 lb.ft)

    G12803055Courtesy of KIA MOTORS AMERICA, INC.
  9. Disconnect the RH intercooler inlet hose (A).

    Tightening torque: 

    4.9 - 6.9 N.m (0.5 - 0.7 kgf.m, 3.6 - 5.1 lb.ft, 43.4 - 60.8 lb.in)

    (If equipped with a cap, tighten it until the cap is removed.)

    G12803056Courtesy of KIA MOTORS AMERICA, INC.
  10. Remove the RH warm-up catalytic converter (WCC) stay (A).

    Tightening torque: 

    34.3 - 41.2 N.m (3.5 - 4.2 kgf.m, 25.3 - 30.4 lb.ft)

    G12803057Courtesy of KIA MOTORS AMERICA, INC.
  11. Remove the heated oxygen sensor (HO2S).

    (Refer to " HEATED OXYGEN SENSOR (HO2S)  ") 

  12. Remove the RH warm-up catalytic converter (WCC) (A).

    Tightening torque: 

    35.3 - 41.2 N.m (3.6 - 4.2 kgf.m, 26.0 - 30.4 lb.ft)

    G12803058Courtesy of KIA MOTORS AMERICA, INC.
  13. Remove the RH warm-up catalytic converter (WCC) gasket (A).
    G12803059Courtesy of KIA MOTORS AMERICA, INC.
  14. Remove the LH/RH engine mounting insulator nut (A).

    Tightening torque: 

    63.7 - 83.4 N.m (6.5 - 8.5 kgf.m, 47.0 - 61.5 lb.ft)

    [LH] 

    G12803060Courtesy of KIA MOTORS AMERICA, INC.

    [RH] 

    G12803061Courtesy of KIA MOTORS AMERICA, INC.
  15. Hook the engine hoist to the hole of engine hanger.
  16. Lift the engine slightly using the hoist to obtain space for removing the RH engine mounting support bracket.
  17. Remove the engine mounting support bracket (A).

    Tightening torque: 

    49.0 - 58.8 N.m (5.0 - 6.0 kgf.m, 36.2 - 43.4 lb.ft)

    G12803062Courtesy of KIA MOTORS AMERICA, INC.
  18. Remove the RH turbocharger oil drain pipe mounting nuts (A).

    Tightening torque: 

    9.8 - 11.8 N m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12803063Courtesy of KIA MOTORS AMERICA, INC.
  19. Remove the RH turbo manifold module stay (A).

    Tightening torque: 

    26.5 - 31.4 N.m (2.7 - 3.2 kgf.m, 19.5 - 23.1 lb.ft)

    G12803064Courtesy of KIA MOTORS AMERICA, INC.
  20. Remove the RH turbocharger oil feed pipe eye bolt (A).

    Tightening torque: 

    11.8 - 17.7 N.m (1.2 - 1.8 kgf.m, 8.7 - 13.0 lb.ft)

    G12803065Courtesy of KIA MOTORS AMERICA, INC.
  21. Remove the RH turbo manifold module (A).

    Tightening torque: 

    58.8 - 63.7 N.m (6.0 - 6.5 kgf.m, 43.4 - 47.0 lb.ft)

    G12803066Courtesy of KIA MOTORS AMERICA, INC.
  22. Remove the RH turbo manifold module gasket (A).
    G12803067Courtesy of KIA MOTORS AMERICA, INC.
  23. Remove the RH turbocharger oil drain pipe (A).

    Tightening torque: 

    9.8 - 11.8 N m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12803068Courtesy of KIA MOTORS AMERICA, INC.
  24. Remove the alternator.

    (Refer to " ALTERNATOR  ") 

  25. Remove the alternator bracket (A).

    Tightening torque: 

    49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47.0 lb.ft)

    G12803069Courtesy of KIA MOTORS AMERICA, INC.
  26. Remove the RH turbocharger oil feed pipe (A).

    Tightening torque: 

    66.7 - 70.6 N.m (6.8 - 7.2 kgf.m, 49.2 - 52.1 lb.ft)

    G12803070Courtesy of KIA MOTORS AMERICA, INC.
  27. Install in the reverse order of removal.
    NOTE:
    • Always use a new RH turbo manifold module gasket.
    • Take care whether the oil feed pipe & hose assembly is interfered with turbo manifold module and any surrounding parts.
    • If the oil feed pipe & hose is damaged, engine oil is not supplied sufficiently to the turbocharger then it may damage the turbocharger. If the oil drain pipe & hose is damaged and clogged, engine oil is not drained smoothly then it may cause oil leaks from the turbocharger.

      Be care full the oil feed pipe & hose not to damage. (bent, crushed, torn or cracked).

    • When installing the RH turbo manifold module, tighten the nuts with pre-torque first, and then tighten the nuts with specified torque in the sequence shown.
      Fig 1: RH Exhaust Manifold Nuts Tightening Sequence
      G12803071Courtesy of KIA MOTORS AMERICA, INC.
    • When installing the RH warm-up catalytic converter (WCC), tighten the nuts with pre-torque first, and then tighten the nuts with specified torque in the sequence shown.
    G12803072Courtesy of KIA MOTORS AMERICA, INC.