LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2019 >> Stinger GTS, AWD >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Intake And Exhaust System 3.3L >> Turbo Manifold Module And Catalytic Converter >> Repair Procedures >> Removal And Installation >> LH Turbo Manifold Module

LH Turbo Manifold Module

  1. Remove the engine and transmission assembly.

    (Refer to " ENGINE AND TRANSMISSION ASSEMBLY  ") 

  2. Disconnect the LH electric waste gate actuator (EWGA) connector (A).
    G12803030Courtesy of KIA MOTORS AMERICA, INC.
  3. Remove the LH turbo manifold module heat protector (A).

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12803031Courtesy of KIA MOTORS AMERICA, INC.
  4. Disconnect the LH turbocharger water hose (A).
    G12803032Courtesy of KIA MOTORS AMERICA, INC.
  5. Remove the LH turbocharger water hose & pipe (A)

    Tightening torque 

    Eye bolts:

    33.3 - 39.2 N.m (3.4 - 4.0 kgf.m, 26.6 - 28.9 lb.ft)

    Bolt:

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12803033Courtesy of KIA MOTORS AMERICA, INC.
  6. Remove the heated oxygen sensor (HO2S) wiring bracket (A) and then remove the heated oxygen sensor (HO2S) connector (B).
    G12803034Courtesy of KIA MOTORS AMERICA, INC.
  7. Disconnect the water hose (A).
    G12803035Courtesy of KIA MOTORS AMERICA, INC.
  8. Remove the water outlet pipe (A).

    Tightening torque: 

    24.5 - 28.4 N.m (2.5 - 2.9 kgf.m, 18.1 - 21.0 lb.ft)

    G12803036Courtesy of KIA MOTORS AMERICA, INC.
  9. Disconnect the LH intercooler inlet hose (A).

    Tightening torque: 

    4.9 - 6.9 N.m (0.5 - 0.7 kgf.m, 3.6 - 5.1 lb.ft. 43.4 - 60.8 lb.in)

    (If equipped with a cap, tighten it until the cap is removed.)

    G12803037Courtesy of KIA MOTORS AMERICA, INC.
  10. Remove the LH warm-up catalytic converter (WCC) stay (A).

    Tightening torque: 

    34.3 - 41.2 N.m (3.5 - 4.2 kgf.m, 25.3 - 30.4 lb.ft)

    G12803038Courtesy of KIA MOTORS AMERICA, INC.
  11. Remove the LH warm-up catalytic converter (WCC) (A).

    Tightening torque: 

    35.3 - 41.2 N.m (3.6 - 4.2 kgf.m, 26.0 - 30.4 lb.ft)

    G12803039Courtesy of KIA MOTORS AMERICA, INC.
  12. Remove the LH warm-up catalytic converter (WCC) gasket (A).
    G12803040Courtesy of KIA MOTORS AMERICA, INC.
  13. Remove the A/C compressor.

    (Refer to " COMPRESSOR  ") 

  14. Remove the LH turbocharger oil drain pipe mounting nuts (A).

    Tightening torque: 

    9.8 - 11.8 N m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12803041Courtesy of KIA MOTORS AMERICA, INC.
  15. Remove the LH turbo manifold module stay (A).

    Tightening torque: 

    26.5 - 31.4 N.m (2.7 - 3.2 kgf.m, 19.5 - 23.1 lb.ft)

    G12803042Courtesy of KIA MOTORS AMERICA, INC.
  16. Remove the LH turbocharger oil feed pipe (A).

    Tightening torque 

    Eye bolts:

    11.8 - 17.7 N.m (1.2 - 1.8 kgf.m, 8.7 - 13.0 lb.ft)

    Bolt:

    9.8 - 11.8 N m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12803043Courtesy of KIA MOTORS AMERICA, INC.
  17. Remove the LH turbo manifold module (A).

    Tightening torque: 

    58.8 - 63.7 N.m (6.0 - 6.5 kgf.m, 43.4 - 47.0 lb.ft)

    G12803044Courtesy of KIA MOTORS AMERICA, INC.
  18. Remove the LH turbo manifold module gasket (A).
    G12803045Courtesy of KIA MOTORS AMERICA, INC.
  19. Remove the LH turbocharger oil drain pipe (A).

    Tightening torque: 

    9.8 - 11.8 N m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12803046Courtesy of KIA MOTORS AMERICA, INC.
  20. Install in the reverse order of removal.
    NOTE:
    • Always use a new LH turbo manifold module gasket.
    • Take care whether the oil feed pipe & hose assembly is interfered with turbo manifold module and any surrounding parts.
    • If the oil feed pipe & hose is damaged, engine oil is not supplied sufficiently to the turbocharger then it may damage the turbocharger. If the oil drain pipe & hose is damaged and clogged, engine oil is not drained smoothly then it may cause oil leaks from the turbocharger.

      Be care full the oil feed pipe & hose not to damage. (bent, crushed, torn or cracked).

    • When installing the LH turbo manifold module, tighten the nuts with pre-torque first, and then tighten the nuts with specified torque in the sequence shown.
      Fig 1: LH Exhaust Manifold Nuts Tightening Sequence
      G12803047Courtesy of KIA MOTORS AMERICA, INC.
    • When installing the LH warm-up catalytic converter (WCC), tighten the nuts with pre-torque first, and then tighten the nuts with specified torque in the sequence shown.
    G12803048Courtesy of KIA MOTORS AMERICA, INC.