LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2015 >> Optima Limited >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Campaigns >> Body Electrical >> HECU/Abs Module Parasitic Current Draw Test & Replacement & Multi-Fuse Replacement (SC212) (SC212)

HECU/Abs Module Parasitic Current Draw Test & Replacement & Multi-Fuse Replacement (SC212) (SC212)

Publication date: 2021-06-30
Reference number: SC212
Supersedes refnos: SC197, SC197 REV 1, SC197 REV 2

HECU/ABS MODULE PARASITIC CURRENT DRAW TEST & REPLACEMENT & MULTI-FUSE REPLACEMENT (SC212)

HECU/ABS MODULE PARASITIC CURRENT DRAW TEST & REPLACEMENT & MULTI-FUSE REPLACEMENT (SC212)

SERVICE CAMPAIGN BULLETIN

Reference Number(s): SC212, Date of Issue:  June 30, 2021
KIA: 2013-2015MY Optima (QF) 2014-2015MY Sorento (XMa)
GROUP: Safety Recall Campaign

SERVICE INFORMATION

This bulletin supersedes SC197  and provides the procedure to inspect, and, if necessary, replace the Hydraulic Electronic Control Unit (HECU) on some 2013-2015MY Optima (QF) vehicles produced from July 12, 2013 through October 2, 2015 and  some 2014-2015MY Sorento (XMa) vehicles produced from June 17, 2013 through December 11, 2014. In addition, this bulletin provides the procedure to replace the Multi-Fuse in the above referenced vehicles. Brake fluid may leak internally inside the Hydraulic Electronic Control Unit (HECU) which, over time, can result in an electrical short. An electrical short in the HECU increases the risk of an engine compartment fire.

Dealers are to have technicians measure the Anti-Lock Brake System (ABS) circuit in the fuse box for parasitic current draw and inspect HECU connnection (male and female connector) for any signs of suspected thermal damage (melt, burn, oil leakage, etc.) If the current draw is >70uA, the HECU assembly is to be replaced due to possible internal damage caused by an internal fluid leak. Before conducting the procedure, verify that the vehicle is included in the list of affected VINs.

NOTE: A Techline case number is required for all part orders to confirm the actual microamp draw is present at time of vehicle inspection prior to the part order.
NOTE: There is no charge to the vehicle owner for this repair. Under applicable law, you may not sell or otherwise deliver any affected vehicle until it has been repaired pursuant to the procedures set forth in this bulletin.
NOTE: To assure complete customer satisfaction, always remember to refer to WebDCS Warranty Coverage (validation) Inquiry Screen (Service → Warranty Coverage → Warranty Coverage Inquiry) for a list of any additional campaigns that may need to be performed on the vehicle before returning it to the customer.
IMPORTANT: This test procedure must be performed with the ignition 'OFF'. (DO NOT 'START' the engine at any time during the test procedure.

SETTING THE SST MULTIMETER

  1. Connect two (2) lead wires (red and black) to the SST.

    Black Ground (-) lead wire; connect to COM Positive (+) lead wire; connect to VΩmA. 

    G13833020
    G13833021
  2. Turn the selection knob to the right and set it to 200uA  .
    G13833022

    Reading Microamps:

    Meter Setting Displayed Value
    200uA 0 - 200
    2000uA DO NOT USE
    10A DO NOT USE
    G13833023

TEST PROCEDURE

  1. Open the hood and disconnect the negative (-) battery terminal (A).
  2. Remove the fuse box cover (B).
    G13833024
  3. Locate the Multi Fuse (C) ESC1 for (QF) Optima or ABS2 for (XMa) Sorento 40A in the fuse box.
    G13833025
    G13833026
  4. Loosen the 10mm Multi Fuse retaining nut (D) and remove the Multi Fuse.

    Optima (QF) ONLY, remove the nut cover first.

    Sorento (XMA) ONLY, after removing the fuse, re-attach the 12VDC cable to the fuse box, and temporarily re-install the Multi Fuse 10mm nut.

    G13833027
    G13833028
    G13833029
  5. Reconnect the negative (-) battery terminal.
    1. Using the two (2) SST Multimeter jumper leads, carefully contact the 'black' lead to the 'ESC1' (QF) or 'ABS2' (XMa)  fuse terminal and the 'red' lead to the fuse box 'Positive' (E) post  .
    2. Measure the Multimeter value/reading for at least 15 seconds.
      NOTE: The current draw value must stay constant.
      CAUTION: DO NOT  damage the terminals.

      If current draw value is OVER 70uA or 0.070mA  , open a Techline case and attach a picture of the meter reading for review prior to part order. All part orders are on manual allocation. 

      Replace the Hydraulic Electronic Control unit (HECU)  by referring to the "Brake System → ESC (Electronic Stability Control) System → ESC Control Module → Repair procedures" chapter in the applicable Shop Manual on KGIS.

      Replace the Multi-Fuse with the one from the Service Kit  by referring to the "Body Electrical → Fuses And Relays → Relay Box (Engine compartment) → Repair procedures → Multi Fuse" chapter in the applicable Shop Manual on KGIS.

    3. If current draw value is BELOW 70uA or 0.070mA, replace the Multi-Fuse with the one supplied in the Service Kit  by referring to the → Repair procedures → Multi Fuse" chapter in the applicable Shop Manual on KGIS.
    NOTE: Drill a hole through the center of the removed fuse(s) and discard. DO NOT  reuse.
    IMPORTANT: The inspection on step 7 must  be performed after current draw test.
  6. Disconnect the HECU connector and inspect the inside of the connector with good lighting for signs of thermal damage at both terminals.

    If the wire harness has suspected signs of thermal damage as shown  , open a Techline case and attach a picture of the damaged connector and hold for further assistance.

    NOTE: Example of thermally damaged (melted housing) connector/terminal (NG) shown to the right.
    G13833030
    G13833031
    NOTE: Example of normal (undamaged) connector/terminal (OK) shown to the right.
    G13833032
  7. Replace the fuse box cover with the Upper Cover from the Service Kit.
  8. Reinstall the removed parts in the reverse order of removal.
NOTE: All parts replaced are subject to return to the Warranty Parts Return Center (WPRC) for verification of the reported parasitic draw.

AFFECTED VEHICLE RANGE

Model Production Date Range
Optima (QF) July 12, 2013 to October 2, 2015
Sorento (XMa) June 17, 2013 to December 11, 2014

REQUIRED TOOL

Tool Name Figure Part Number Comments
Multimeter DT-830D
G13833033
SC197Meter Only one (1) multimeter set was auto shipped to each dealer by MPA, P/N: KQ589 4C100QQK. Additional warrantable concerns will be handled by  Snap-On Business Solutions(1).
G13833034
SC197Leads
(1) Call Snap-on Business Solutions at (888) 542-1011 for lead replacements or defective meter.

REQUIRED PART

Part Name Part Number Figure Qty.
HECU Assembly(1) (XMa) 58920 1U000QQK
G13833035
1
(1)Techline case number will be required prior to part order.
HECU Assembly(1) (QF) 13MY 58920 4C550QQK w/EPB
58920 2T550QQK w/o EPB
HECU Assembly(1) (QF) 14-15MY 58920 4C870QQK w/EPB
58920 2T870QQK w/o EPB
Service Kit (13MY QF) 91NON 2TEU1QQK (2.4L)
91YES 2TEU1QQK (2.0L-T)
G13833036
1
Service Kit (14-15MY QF) 91PEN 2TEU1QQK (2.4L)
91PEY 2TEU1QQK (2.0L-T)
Service Kit (XMa) 91KIT 2PUSAQQK
Front Wire Harness (XMa and QF) Refer to EPC
G13833037
1
(1) Refer to EPC for the applicable required part per model VIN.

WARRANTY INFORMATION

N Code: N99 C Code: C99 

Model Claim Type Causal P/N Qty. Repair Description Labor Op Code Op Time Replacement P/N Qty.
XMa R 58920 1U000 0 (SC212) HECU Current (OK) + Connector Inspection + Service Kit Installation 211A15I0 0.3 M/H 91KIT 2PUSAQQK 1
(SC212) HECU Current (NG) + Connector (OK) + HECU Replacement + Service Kit Installation 211A15R0 2.1 M/H 91KIT 2PUSAQQK 1
58920 1U000QQK 1
(SC212) HECU Current (NG) + Connector (NG) HECU + Wire Harness Replacement + Service Kit Installation 211A15RA(1) 8.0 M/H 91KIT 2PUSAQQK 1
58920 1U000QQK 1
Wire harness Refer to EPC(1) 1
13MY QF (2.4) 58920 4C550 (SC212) HECU Current (OK) + Connector Inspection + Service Kit Installation 211A16I0 0.3 M/H 91NON 2TEU1QQK 1
(SC212) HECU Current (NG) + Connector (OK) + HECU Replacement + Service Kit Installation 211A16R0 2.0 M/H 91NON 2TEU1QQK 1
58920 4C550QQK(2)or  58920 2T550QQK(2) 1
(SC212) HECU Current (NG) + Connector (NG) HECU + Wire Harness Replacement + Service Kit Installation 211A16RA(1) 7.4 M/H 91NON 2TEU1QQK 1
58920 4C550QQK(2) or 58920 2T550QQK(2) 1
Wire harness Refer to EPC(1) 1
13MY QF (2.0T) 58920 4C550 (SC212) HECU Current (OK) + Connector Inspection + Service Kit Installation 211A16I1 0.3 M/H 91YES 2TEU1QQK 1
(SC212) HECU Current (NG) + Connector (OK) + HECU Replacement + Service Kit Installation 211A16R1 2.0 M/H 91YES 2TEU1QQK 1
58920 4C550QQK(2)or  58920 2T550QQK(2) 1
(SC212) HECU Current (NG) + Connector (NG) HECU + Wire Harness Replacement + Service Kit Installation 211A16RB(1) 7.4 M/H 91YES 2TEU1QQK 1
58920 4C550QQK(2)or  58920 2T550QQK(2) 1
Wire harness Refer to EPC(1) 1
14-15MY QF (2.4) 58920 4C550 (SC212) HECU Current (OK) + Connector Inspection + Service Kit Installation 211A16I2 0.3 M/H 91PEN 2TEU1QQK 1
(SC212) HECU Current (NG) + Connector (OK) + HECU Replacement + Service Kit Installation 211A16R2 2.0 M/H 91PEN 2TEU1QQK 1
58920 4C870QQK(2)or  58920 2T870QQK(2) 1
(SC212) HECU Current (NG) + Connector (NG) HECU + Wire Harness Replacement + Service Kit Installation 211A16RC(1) 7.4 M/H 91PEN 2TEU1QQK 1
58920 4C870QQK(2)or  58920 2T870QQK(2) 1
Wire harness Refer to EPC(1) 1
14-15MY QF (2.0T) 58920 4C550 (SC212) HECU Current (OK) + Connector Inspection + Service Kit Installation 211A16I3 0.3 M/H 91PEY 2TEU1QQK 1
(SC212) HECU Current (NG) + Connector (OK) + HECU Replacement + Service Kit Installation 211A16R3 2.0 M/H 91PEY 2TEU1QQK 1
58920 4C870QQK(2)or  58920 2T870QQK(2) 1
(SC212) HECU Current (NG) + Connector (NG) HECU + Wire Harness Replacement + Service Kit Installation 211A16RD(1) 7.4 M/H 91PEY 2TEU1QQK 1
58920 4C870QQK(2) or 58920 2T870QQK(2) 1
Wire harness Refer to EPC(1) 1
NOTE:
(1) If wire harness is NG, a Techline case must be opened for each wire harness ordered. (Refer to Warranty Bulletin 2021-13 for required model P/N).
(2) Only one (1) applicable HECU replacement P/N can be claimed for QF model. Refer to Warranty Bulletin 2021-13 for claim submission procedures. Use sublet code X1 for reimbursement for Kia Brake Fluid P/N: UM010 CH043, DOT 4 ($9 maximum).
NOTE: VIN inquiry data for this repair is provided for tracking purposes only. Kia retailers should reference SC212  when accessing the WebDCS system.