LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2015 >> Cadenza Premium >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Cylinder Block >> Piston And Connecting Rod >> Repair Procedures >> Reassembly

Repair Procedures: Reassembly

NOTE:
  • Thoroughly clean all parts to be assembled.
  • Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
  • Replace all gaskets, O-rings and oil seals with new parts.
  1. Assemble the piston and the connecting rod.
    1. Install the piston pin with snap ring 2EA and check the snap ring assembly thoroughly.
    2. The piston front mark (A) and the connecting rod front mark (B) must face the timing belt side of the engine.
      Fig 1: Identifying Piston Front Mark And Connecting Rod Front Mark
      G09750908Courtesy of KIA MOTORS AMERICA, INC.
  2. Install the piston rings.
    1. Install the coil spring and oil ring by hand.
    2. Using a piston ring expander, install the 2 compression rings with the code mark facing upward.
    3. Position the piston rings so that the ring ends are as shown.
      Fig 2: Installing Piston Rings
      G09750909Courtesy of KIA MOTORS AMERICA, INC.
  3. Install the connecting rod bearings.
    1. Align the bearing claw with the groove of the connecting rod or connecting rod cap.
    2. Install the bearings (A) in the connecting rod and connecting rod cap (B).
      Fig 3: Identifying Bearings And Connecting Rod Cap
      G09750910Courtesy of KIA MOTORS AMERICA, INC.
      NOTE: When reassembling the connecting rods and the caps, ensure the front marks on then and the number of cylinder.
  4. Attach the piston and connecting rod assemblies from the cylinder block.
    NOTE: Before installing the pistons, apply a coat of engine oil to the ring grooves and cylinder bores.
    1. Install the ring compressor, check that the bearing is securely in place, then position the piston in the cylinder, and tap it in using the wooden handle of a hammer.
    2. Stop after the ring compressor pops free, and check the connecting rod-to-check journal alignment before pushing the piston into place.
    3. Install the rod caps with bearings, and torque the bolts.

      Tightening torque: 

      [27.5 ~ 31.4 N.m (2.8 ~ 3.2 kgf.m, 20.3 ~ 23.1 lb-ft)] + [68 ~ 72°]

      NOTE:
      • Always use new connecting rod cap bolts. Connecting rod cap bolts are toque-to-yield bolts designed to be permanently elongated beyond the state of elasticity when torqued, so if the bolts are removed and reused, it may cause the bolts to break or fail to maintain clamping force.
      • Maintain downward force on the ring compressor to prevent the rings from expanding before entering the cylinder bore.
      Fig 4: Applying Downward Force On Ring Compressor
      G09750911Courtesy of KIA MOTORS AMERICA, INC.
      NOTE: Use SST (09221-4A000), install connecting rod bearing cap bolts.
      Fig 5: Connecting Rod Bearing Cap Bolts
      G09750912Courtesy of KIA MOTORS AMERICA, INC.
  5. Install the baffle plate.

    Install and uniformly tighten the baffle plate bolts, in several passes, in the sequence shown.

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 6: Baffle Plate Tightening Sequence
    G09750913Courtesy of KIA MOTORS AMERICA, INC.
  6. Assemble the other parts in the reverse order of disassembly.