LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2009 >> Rondo EX, 2.4 8 >> Repair and Diagnosis >> Steering >> Steering Column & Shaft >> Repair Procedures >> Installation

Repair Procedures: Installation

CAUTION: Apply the multipurpose grease to sliding of the each part before installation.
  1. Install the steering column & universal joint assembly (B) by tightening the mounting bolts and nuts (A).

    Tightening torque Nm (kgf.m, lb-ft): 

    13 ~ 18 (1.3 ~ 1.8, 9 ~ 13)

    Fig 1: Identifying Steering Column/Universal Joint Assembly & Mounting Bolts/Nuts
    G06386691Courtesy of KIA MOTORS AMERICA, INC.
    CAUTION: Unlike the existing steering column, new replacement part has a pin to prevent the column shaft from tilting, be sure to remove the pin from the tilt bracket after installing the new part.
  2. Connect the connector (A, B).
    Fig 2: Identifying Connectors (1 Of 2)
    G06386692Courtesy of KIA MOTORS AMERICA, INC.
    Fig 3: Identifying Connectors (2 Of 2)
    G06386693Courtesy of KIA MOTORS AMERICA, INC.
  3. Install the reinforce panel (A) by tightening mounting bolts.
    Fig 4: Identifying Reinforce Panel
    G06386694Courtesy of KIA MOTORS AMERICA, INC.
  4. Connect the universal joint assembly (B) with the pinion of the steering gear and then tightening the bolt (A).

    Tightening torque Nm (kgf.m, lb-ft): 

    30 ~ 35 (3.0 ~ 3.5, 22 ~ 25)

    Fig 5: Identifying Universal Joint Assembly & Bolt
    G06386695Courtesy of KIA MOTORS AMERICA, INC.
  5. Install the multifunction switch (A) to the steering column assembly.
    Fig 6: Identifying Multifunction Switch
    G06386696Courtesy of KIA MOTORS AMERICA, INC.
  6. Install the clock spring (A) to steering column assembly and then connect the connectors.
    Fig 7: Identifying Clock Spring
    G06386697Courtesy of KIA MOTORS AMERICA, INC.
    CAUTION: When installing the clock spring, make sure to prevent the damage of clock spring inner cable. Refer to AIRBAG MODULE .
  7. Install the steering column upper and lower shroud (A, B).
    Fig 8: Identifying Steering Column Upper & Lower Shroud
    G06386698Courtesy of KIA MOTORS AMERICA, INC.
  8. Install the lower crash pad (A).
    Fig 9: Identifying Lower Crash Pad
    G06386699Courtesy of KIA MOTORS AMERICA, INC.
  9. Install the parking brake release lever (A) to lower crash pad.
    Fig 10: Identifying Parking Brake Release Lever
    G06386700Courtesy of KIA MOTORS AMERICA, INC.
  10. Install the steering wheel to the steering column shaft and then tighten the lock nut and washer together.

    Tightening torque Nm (kgf.m, lb-ft): 

    40 ~ 50 (4.0 ~ 5.0, 29 ~ 36)

  11. Connect the remote switch connector (A) and install the dynamic damper (B).
    Fig 11: Identifying Remote Switch Connector & Dynamic Damper
    G06386701Courtesy of KIA MOTORS AMERICA, INC.
  12. Connect the air bag module and horn connector (A, B) to the air bag module and then install the air bag module to the steering wheel.
    Fig 12: Identifying Air Bag Module Connector & Horn Connector
    G06386702Courtesy of KIA MOTORS AMERICA, INC.
  13. Tighten the torx bolts which are located on the both side of steering wheel.
    Fig 13: Locating Torx Bolts
    G06386703Courtesy of KIA MOTORS AMERICA, INC.
  14. Connect the battery negative cable to the battery.