LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2009 >> Rondo EX, 2.4 8 >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Timing System - 2.4L >> Timing Chain >> Installation

Timing Chain: Installation

  1. Install the crankshaft chain sprocket (B).
  2. Install the timing chain oil jet (A).

    Tightening torque : 

    7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

    Fig 1: Identifying Timing Chain Oil Jet & Crankshaft Chain Sprocket
    G06385851Courtesy of KIA MOTORS AMERICA, INC.
  3. Set crankshaft that the key of crankshaft should be aligned with the mating surface of main bearing cap. Put the intake, exhaust camshaft assembly that the TDC mark of intake sprocket and exhaust sprocket should be aligned with the top surface of cylinder head. As a result of this, place the piston on No. 1 cylinder at the top dead center on compression stroke.
  4. Install the timing chain guide (A).

    Tightening torque : 

    9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)

    Fig 2: Identifying Timing Chain Guide
    G06385852Courtesy of KIA MOTORS AMERICA, INC.
  5. Install the timing chain.

    To install the timing chain with no slack between each shaft (cam, crank), follow the below procedure. Crankshaft sprocket (A) -> Timing chain guide (B) -> Intake camshaft sprocket (C) -> Exhaust camshaft sprocket (D).

    The timing mark of each sprockets should be matched with timing mark (color link) of timing chain at installing timing chain.

    Fig 3: Identifying Crankshaft Sprocket, Timing Chain Guide, & Intake/Exhaust Camshaft Sprockets
    G06385853Courtesy of KIA MOTORS AMERICA, INC.
  6. Install the timing chain tensioner arm (B).

    Tightening torque : 

    9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)

  7. Install the timing chain auto tensioner (A) and remove the set pin.

    Tightening torque : 

    9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)

    Fig 4: Identifying Timing Chain Auto Tensioner & Timing Chain Tensioner Arm
    G06385854Courtesy of KIA MOTORS AMERICA, INC.
  8. After rotating crankshaft 2 revolutions in regular direction (clockwise viewed from front), confirm the timing mark.
    Fig 5: Identifying Timing Mark
    G06385855Courtesy of KIA MOTORS AMERICA, INC.
  9. Install timing chain cover.
    1. The sealant locations on chain cover and on counter parts (cylinder head, cylinder block, and ladder frame) must be free of engine oil and ETC.
    2. Before assembling the timing chain cover, the liquid sealant Loctite 5900H should be applied on the gap between cylinder head and cylinder block.

      The part must be assembled within 5 minutes after sealant was applied.

      Bead width  : 3.0mm (0.12in.)

      Fig 6: Identifying Sealant Application Areas - Head/Block
      G06385856Courtesy of KIA MOTORS AMERICA, INC.
    3. After applying liquid sealant Loctite 5900H on timing chain cover, the part must be assembled within 5 minutes after sealant was applied. Sealant should be applied without discontinuity.

      Bead width  : 3.0mm (0.12in.)

      Fig 7: Identifying Sealant Application Area - Timing Chain Cover
      G06385857Courtesy of KIA MOTORS AMERICA, INC.
    4. The dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover to be in exact position.

      Tightening torque : 

      M6: 7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

      M8: 18.6 ~ 22.5N.m (1.9 ~ 2.3kgf.m, 13.7 ~ 16.6lb-ft)

      Fig 8: Identifying Timing Chain Cover
      G06385858Courtesy of KIA MOTORS AMERICA, INC.
    5. The firing and/or blow out test should not be performed within 30 minutes after the timing chain cover was assembled.
  10. Install the oil pan.
    1. Using a gasket scraper, remove all the old packing material from the gasket surfaces.
    2. Before assembling the oil pan, the liquid sealant Loctite 5900H should be applied on oil pan. The part must be assembled within 5 minutes after the sealant was applied.
      Fig 9: Identifying Sealant Application Area - Oil Pan
      G06385859Courtesy of KIA MOTORS AMERICA, INC.
      CAUTION:
      • When applying sealant gasket, sealant must not be protruded into the inside of oil pan.
      • To prevent leakage of oil, apply sealant gasket to the inner threads of the bolt holes.
    3. Install the oil pan (A).

      Uniformly tighten the bolts in several passes.

      Tightening torque : 

      M8 (B): 26.5 ~ 30.4N.m (2.7 ~ 3.1kgf.m, 19.5 ~ 22.4lb-ft)

      M6 (C): 9.8 ~ 11.8N.m (1.0 ~ 1.2kgf.m, 7.2 ~ 8.7lb-ft)

      Fig 10: Identifying Oil Pan With Bolts
      G06385860Courtesy of KIA MOTORS AMERICA, INC.
    4. After assembly, wait at least 30 minutes before filling the engine with oil.
  11. Install the air compressor bracket (A).

    Tightening torque : 

    19.6 ~ 23.5N.m (2.0 ~ 2.4kgf.m,13.7 ~ 14.5lb-ft)

    Fig 11: Identifying Air Compressor Bracket
    G06385861Courtesy of KIA MOTORS AMERICA, INC.
  12. Install the air compressor lower bolts.

    Tightening torque : 

    19.6 ~ 24.5N.m (2.0 ~ 2.5kgf.m,13.7 ~ 18.1lb-ft)

    Fig 12: Identifying Air Compressor Lower Bolts
    G06385862Courtesy of KIA MOTORS AMERICA, INC.
  13. Install the cylinder head cover.
    1. The hardening sealant located on the upper area between timing chain cover and cylinder head should be removed before assembling cylinder head cover.
    2. After applying sealant (Loctite 5900H), it should be assembled within 5 minutes.

      Bead width  : 2.5mm (0.1in.)

      Fig 13: Identifying Sealant Application Areas - Timing Chain Cover/Cylinder Head
      G06385863Courtesy of KIA MOTORS AMERICA, INC.
    3. The firing and/or blow out test should not be performed within 30 minutes after the cylinder head cover was assembled.
    4. Install the cylinder head cover bolts as following method.

      Tightening torque : 

      Step 1: 3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3lb-ft)

      Step 2: 7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

      Fig 14: Identifying Tightening Sequence Of Cylinder Head Cover Bolts
      G06385864Courtesy of KIA MOTORS AMERICA, INC.
      CAUTION: Do not reuse cylinder head cover gasket.
  14. Install the ignition coils (A).

    Tightening torque : 

    3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3lb-ft)

    Fig 15: Identifying Ignition Coils
    G06385865Courtesy of KIA MOTORS AMERICA, INC.
  15. Connect the ignition coil connectors (A).
    Fig 16: Identifying Ignition Coil Connectors
    G06385866Courtesy of KIA MOTORS AMERICA, INC.
  16. Install the PCV hose (A).
    Fig 17: Identifying PCV Hose
    G06385867Courtesy of KIA MOTORS AMERICA, INC.
  17. Install the breather hose (A).
    Fig 18: Identifying Breather Hose
    G06385868Courtesy of KIA MOTORS AMERICA, INC.
  18. Connect the exhaust OCV connector (A) and replace the wiring on the cylinder head cover.
    Fig 19: Identifying Exhaust OCV Connector
    G06385869Courtesy of KIA MOTORS AMERICA, INC.
  19. Install the engine support bracket (C).

    Tightening torque : 

    M10: 39.2 ~ 44.1N.m (4.0 ~ 4.5kgf.m, 28.9 ~ 32.5lb-ft)

    M8: 19.6 ~ 24.5N.m (2.0 ~ 2.5kgf.m, 14.5 ~ 18.1lb-ft)

  20. Install the crankshaft pulley (B).

    Tightening torque : 

    166.6 ~ 176.4N.m (17.0 ~ 18.0kgf.m, 122.9 ~ 130.1lb-ft)

    NOTE: Use the SST (flywheel stopper, 09231-3K000) to install the crankshaft pulley bolt, after remove the starter.
  21. Install the water pump pulley (A).

    Tightening torque : 

    7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

    Fig 20: Identifying Water Pump Pulley, Crankshaft Pulley, & Engine Support Bracket
    G06385870Courtesy of KIA MOTORS AMERICA, INC.
  22. Install the drive belt tensioner (B).

    Tightening torque : 

    53.9 ~ 63.7N.m (5.5 ~ 6.5kgf.m, 39.7 ~ 47.0lb-ft)

    NOTE: Tensioner pulley bolt is left - handed screw.
  23. Install the idler (A).

    Tightening torque : 

    53.9 ~ 63.7N.m (5.5 ~ 6.5kgf.m, 39.7 ~ 47.0lb-ft)

    Fig 21: Identifying Idler & Drive Belt Tensioner
    G06385871Courtesy of KIA MOTORS AMERICA, INC.
  24. Install the drive belt (A).

    Crankshaft pulley → A/C pulley → Alternator pulley → Idler pulley → P/S pump pulley → Idler pulley → Water pump pulley → Tensioner pulley. Rotate auto tensioner arm in the counter - clockwise moving auto tensioner pulley bolt with wrench. After putting belt on auto tensioner pulley, release the auto tensioner pulley slowly.

    Fig 22: Engine Drive Belt Routing Diagram
    G06385872Courtesy of KIA MOTORS AMERICA, INC.
  25. Install the engine mounting bracket (B) and ground line (A).

    Tightening torque : 

    63.7 ~ 83.4N.m (6.5 ~8.5kgf.m, 47.0 ~ 61.5lb-ft)

    Fig 23: Identifying Engine Mounting Bracket & Ground Line
    G06385873Courtesy of KIA MOTORS AMERICA, INC.
  26. Install the RH side cover.

    Tightening torque : 

    8.8 ~ 10.8N.m (0.9 ~ 1.1kgf.m, 6.5 ~ 7.9lb-ft)

  27. Install the RH front wheel.

    Tightening torque : 

    88.3 ~ 107.9N.m (9.0 ~ 11.0kgf.m, 65.1 ~ 79.6lb-ft)

  28. Install the engine cover (A).
    Fig 24: Identifying Engine Cover
    G06385874Courtesy of KIA MOTORS AMERICA, INC.