LEMON Manuals: Even more car manuals for everyone
Home >> Kia >> 2005 >> Spectra5 2.0 1, Standard >> Repair and Diagnosis >> Engine Performance >> System >> DTC Troubleshooting Procedures - 2.0L >> Troubleshooting For DTC >> DTC P0506: Idle Control System - Rpm Lower Than Expected >> Inspection Procedure

Inspection Procedure

  1. CHECK DTC RELATING TO TPS, MAFS, INJECTOR, PCSV, OR ISCA 
    1. Connect a Hi-Scan (Pro) to the data link connector.
    2. Turn ignition switch to ON position and monitor any other DTCs.

    Are any other DTC relating to TPS, MAFS, injector, PCSV, or ISCA also set?

    1. No:  Go to next step.
    2. Yes: Do all repairs associated with those codes before proceeding with this procedure.
  2. CHECK FREE PLAY OF ACCELERATOR CABLE 
    1. Turn ignition switch to OFF position.
    2. Check the free play of the accelerator cable.

      Specifications: 1.0~2.0 mm (0.0039~0.0079 in)

    Is free play within specification?

    1. Yes:  Go to next step.
    2. No: Adjust cable.
  3. CHECK TPS SIGNAL 
    1. Turn ignition switch to ON position.
    2. Using the Hi-Scan (Pro), monitor the TPS signals while slowly opening the throttle.

      Specification (Voltage): 0.2 ~ 0.8 V at C.T (IDLE) 4.3 ~ 4.8 V at W.O.T

    Is signal within specification?

    1. Yes:  Go to next step.
    2. No: Replace the TPS.
  4. VISUALLY CHECK ISCA FOR CONNECTOR CONDITION 
    1. Turn ignition switch to OFF position and disconnect the ISCA connector.
    2. Thoroughly check the ISCA for loose, bent, corroded, contaminated, deteriorated or damaged connectors. See CONNECTOR INSPECTION PROCEDURE .

    Is any problem present?

    1. Yes:  Go to next step.
    2. No: Repair or replace it.
  5. CHECK ISCA RESISTANCE 
    1. Turn ignition switch to OFF position and then disconnect ISCA connector.
    2. Measure resistance between terminals 2 and 3 of the ISCA closing coil.
    3. Measure resistance between terminals 1 and 2 of the ISCA opening coil.

      Specification (ISCA resistance):

      Fig 1: ISCA COIL #1 (OPEN) Resistance Chart
      G00719509Courtesy of KIA MOTORS AMERICA, INC.
      Fig 2: ISCA COIL #2 (CLOSE) Resistance Chart
      G00719510Courtesy of KIA MOTORS AMERICA, INC.
      Fig 3: Checking ISCA Resistance
      G00719511Courtesy of KIA MOTORS AMERICA, INC.

    Is each resistance within specification?

    1. Yes:  Go to next step.
    2. No: Replace ISCA.
  6. CHECK ISCA FOR NORMAL OPERATION 
    1. Remove ISCA from throttle body and check for blockage and sticking.
    2. Connect terminal 2 of the ISCA connector to a 12V power supply.

      One at a time, momentarily ground terminal 1 of the opening coil and terminal 3 of the closing coil while verifying that the valve closes when the closing coil is grounded and that the valve opens when opening coil is grounded.

    3. Repeat several times to ensure reliability.
      NOTE: While ISCA is removed, inspect the throttle body for obstructions in the idle circuit ports. Repair or replace it.
      Fig 4: Checking ISCA For Normal Operation
      G00719512Courtesy of KIA MOTORS AMERICA, INC.

    Is ISCA working properly?

    1. Yes:  Go to next step.
    2. No: Replace ISCA.
  7. CHECK INTAKE HOSE AND THROTTLE PLATE FOR BLOCKAGE 
    1. Visually check the intake hose and throttle plate for blockage or carbon deposits.

    Is the passage of the intake hose or the throttle plate blocked?

    1. Yes:  Proceed with ECM PROBLEM INSPECTION PROCEDURE .
    2. No: Clean or replace it.