Description And Operation: Notes
DESCRIPTION
The Heated Seats system is comprised of several different components. Those components are:
| 1. | Refer to COMFORT SEAT AND WHEEL MODULE (CSWM) . |
| 2. | Refer to RADIO - Certain Radios contain a soft button heated seat switch. |
| 3. | Refer to BODY CONTROL MODULE (BCM) . |
| 4. | Refer to INTEGRATED CENTER STACK (ICS) MODULE - Contains that hard button heated seat switch. |
| 5. | Refer to HEATED SEAT PAD ELEMENTS - Seat bottom and seat back. |
OPERATION
Vehicles with the heated seat option can be visually identified by the two heated seat switches located in the ICS in the center of the instrument panel. The heated seat system allows the driver and front seat passenger to select from three different levels of heat (low, medium, and high).
The heated seat system operates on battery current received through fused ignition switch output (RUN) circuits, so that the heated seat system will only operate when the engine is running. The heated seat system will turn OFF automatically whenever the engine is turned OFF.
A CSWM is used to control the heated seat system. The CSWM responds to heated seat switch messages and ignition switch status inputs by controlling the 12 volt Direct Current (DC) output to the front seat heating elements through integral solid-state relays.
When either of the ICS hard button heated seat switches are pressed, a switch status message is sent from the ICS over the Controller Area Network-Interior High Speed (CAN-IHS) data bus to the CSWM which signals the CSWM to energize the heating element for the selected seat. Amber Light Emitting Diodes (LED) in each switch indicate the level of heat in use:
- One amber LED indicator - Low
- Two amber LED indicators - Medium
- Three amber LED indicators - High
The CSWM sends the LED illumination message to the ICS over the CAN-IHS data bus.
The CSWM supplies Pulse Width Modulated (PWM) current to the heated seat elements. When high-temperature heating is selected, the heating elements provide a boosted heat level during the first four minutes of operation after heating is activated. The heat output then drops to the normal high-temperature level. If high-level heating is selected, the CSWM will automatically switch to the low level after two hours of continuous operation. At that time, the number of illuminated LEDs changes from three to one, indicating the change. Operation on the low setting also turns off automatically after two hours.
The CSWM provides power to and monitors return signals from a heated seat thermistor to monitor and manage the heat level of the heated seats. The heated seat module will automatically turn off the heating elements if it detects an open or low short in the heating element circuit.
For vehicles equipped with Engine Stop Start (ESS) functionality, the CSWM will deactivate the heated seats during a ESS event if the battery voltage dips below 9v. Once the battery has reached 9.5v, the CSWM reactivated all the heated outputs to the same levels they were operating at prior to the voltage dip.
Drive Comfort System Feature
The Drive Comfort System feature is customer programmable. This system has three settings:
- Remote start only - When the remote start only feature is enabled, the CSWM activates the driver heated seat during a remote start vehicle engine start event only based on ambient temperature.
- Remote start and normal start - When the remote start and normal start feature is enabled, the CSWM activates the driver heated seat during both remote and normal vehicle engine start events based on ambient temperature. The ambient temperature will need to be less than 4.4 °C (40 °F).
- Disabled - If the Driver Comfort System feature is disabled, the CSWM will only activate the driver heated seat when the customer activates the system.
If the ambient temperature is less than 4.4 °C (40 °F), the CSWM will set the heated seats to HIGH and will continue with control of the heated seats for a specified period of time. After this time has expired, normal CSWM heated seat operation will resume. If the ambient temperature is above 4.4 °C (40 °F) when the engine start event occurs, normal CSWM heated seat operation will commence. The Driver Comfort System feature default setting is set to "Remote start and normal start".
Load Shedding - The heated seat outputs participate in the load shed reduction strategy. The CSWM monitors several bus signals to determine which type of load shedding is needed, if any. There are four levels of load shed reduction strategy and the CSWM responds differently to each level:
- Level 1 - If output is active, no change will occur. The CSWM retains the current setting(s).
- Level 2 - If the output is active and the setting is Low, the CSWM will behave normally. If the output is High or Medium, the CSWM will turn off the PWM signal until the temperature reaches the low steady state. Once the low steady state has been achieved, the CSWM resumes its timer operation and diagnostic monitoring of the heated seat system.
- Level 3 or Level 7- If the outputs are active, the CSWM sets these outputs to not active. If the outputs are already inactive, the CSWM prevents this state from changing to active until the load shed event has completed.
The heated seat control system is diagnosed using a scan tool. Refer to DTC INDEX (1 OF 2) and/or DTC INDEX (2 OF 2) .