Diagnostic Test
- READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR THE DTC TO RETURN
- With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
- For future reference, with the scan tool, run and save a vehicle Scan Report and all related recorded data.
- With the scan tool, erase all DTCs.
- Turn the ignition off for a minimum of 10.0 seconds.
- Turn the ignition on.
- Using the When Monitored and Set Conditions above and recorded data, operate the vehicle in the conditions that set the DTC.
- With the scan tool, read DTCs.
Did the DTC return?
Yes
- Go To 2
No
- Perform the INTERMITTENT CONDITION diagnostic procedure. Refer to INTERMITTENT CONDITION .
- CHECK FOR OTHER DTCS
- Refer to the recorded DTCs.
Are there any Starter Relay Control circuit DTCs active or pending in the PCM or Body Control Module (BCM)?
Yes
- Perform the applicable diagnostic procedure(s). Refer to DTC INDEX (1 OF 2) and/or DTC INDEX (2 OF 2) .
No
- Go To 3
- Refer to the recorded DTCs.
- CHECK THE BATTERY SUPPLY TO STARTER RELAY 2
- CHECK THE BATTERY SUPPLY TO STARTER RELAY 1
- Remove the Starter Relay 1 from the PDC.
- Measure the voltage supply to the Starter Relay 1 connector (terminal 30).
Is the voltage equal to Battery voltage?
Yes
- Replace the Starter Relay 1 in accordance with the Service Information.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
No
- Go To 5
- CHECK THE FUSE THAT SUPPLIES STARTER RELAY 1
- Inspect the fuse that supplies Fused B+ to Starter Relay 1 terminal 30.
Is the fuse open?
Yes
- Repair the (T753) Ignition Crank Sense circuit for a short to ground and replace the fuse.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
No
- Verify the Fused B+ supply from the Battery to the Power Distribution Center is present. If the Fused B+ is present, replace the Power Distribution Center in accordance with the Service Information.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
- Inspect the fuse that supplies Fused B+ to Starter Relay 1 terminal 30.
- CHECK THE (T753) IGNITION CRANK SENSE CIRCUIT VOLTAGE AT THE PDC
- Reinstall Starter Relay 2 in the PDC.
- Gain access to the wiring harness connected to the PDC.
- Back probe and measure the voltage on the (T753) Ignition Crank Sense Feed circuit at the PDC connector.
- Attempt an ignition start of the engine.
Is the voltage equal to Battery voltage during cranking?
Yes
- Go To 8
No
- Go To 7
- CHECK THE (T753) IGNITION CRANK SENSE CIRCUIT FOR AN OPEN/HIGH RESISTANCE WITHIN THE PDC
- Turn the ignition off.
- If the PDC wiring harness can be disconnected, disconnect the harness connector. If the harness is hard wired to the PDC back probe the (T753) Ignition Crank Sense circuit at the PDC.
- Remove Starter Relay 2 from the PDC.
- Measure the resistance of the (T753) Ignition Crank Sense circuit between the output of the PDC and terminal 87 of Starter Relay 2.
Is the resistance below 3.0 Ohms?
Yes
- Replace Starter Relay 2.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
No
- Replace the Power Distribution Center in accordance with the Service Information.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
- CHECK THE (T753) IGNITION CRANK SENSE CIRCUIT FOR AN OPEN/HIGH RESISTANCE
- Turn the ignition off.
- If the PDC wiring harness can be disconnected, disconnect the harness connector. If the harness is hard wired to the PDC, remove the Starter Relay 2 and back probe the (T753) Ignition Crank Sense circuit at the PDC.
- Disconnect the PCM C1 harness connector.CAUTION:
Do not probe the PCM harness connectors. Probing the PCM harness connectors will damage the PCM terminals resulting in poor terminal to pin connection. Install the GPEC Diagnostic Adaptor to perform the diagnosis.
NOTE:IMPORTANT - The GPEC Diagnostic Adaptor can add up to 1.5 Ohms of resistance to the circuit.
- If it is necessary to probe a terminal at a PCM harness connector, connect the (special tool #10436, Adapter, GPEC Diagnostic) to the appropriate PCM harness connector.
- Measure the resistance of the Ignition Crank (T753) Sense circuit between the PDC connector and the GPEC Adaptor.
Is the resistance below 3.0 Ohms?
Yes
- Go To 9
No
- Repair the Ignition Crank (T753) Sense circuit for an open or high resistance.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
- CHECK THE PDC CONNECTOR FOR SIGNS OF DAMAGED TERMINALS OR CONNECTION
- Check the terminals and wiring at the PDC for pushed out, broken or damaged terminals.
Were any issues found with the PDC or wiring?
Yes
- Perform the appropriate repair in accordance with the Service Information. Check all of the fuses for an open. If a fuse is open, replace the fuse and retest.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
No
- Go To 10
- Check the terminals and wiring at the PDC for pushed out, broken or damaged terminals.
- CHECK RELATED PCM AND COMPONENT CONNECTIONS
- Perform any Service Bulletins that apply.
- Disconnect all PCM harness connectors.
- Disconnect all related in-line harness connections (if equipped).
- Disconnect the related component harness connectors.
- Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
- Proper connector installation.
- Damaged connector locks.
- Corrosion.
- Other signs of water intrusion.
- Weather seal damage (if equipped).
- Bent terminals.
- Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
- Terminals that have been pushed back into the connector cavity.
- Check for spread terminals and verify proper terminal tension.
Repair any conditions that are found.
- Reconnect all PCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
- Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
- Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
- With the scan tool, erase DTCs.
- Test drive or operate the vehicle in accordance with the when monitored and set conditions.
- With the scan tool, read DTCs.
Did the DTC return?
Yes
- Replace and program the Powertrain Control Module (PCM) in accordance with the Service Information. Refer to MODULE, POWERTRAIN CONTROL (PCM), REMOVAL AND INSTALLATION .
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .
No
- The wiring or poor connection problem has been repaired.
- Perform the POWERTRAIN VERIFICATION TEST. Refer to POWERTRAIN VERIFICATION TEST .