Hands Free Phone
DESCRIPTION
The Hands Free Phone system includes the following major components that are used with a Bluetooth® compatible phone:
| 1. | Refer to MICROPHONE . |
| 2. | Refer to UCONNECT® + SIRIUSXM® GUARDIAN SWITCHES . |
| 3. | Refer to COMBINATION ANTENNA . |
| 4. | Refer to RADIO . |
| 5. | Refer to STEERING WHEEL SWITCHES . |
| 6. | Refer to BODY CONTROL MODULE (BCM) . |
A Uconnect® Hands Free Phone system is factory-installed optional equipment. This system allows connection of compatible mobile phones for hands free use in sending and receiving phone calls and text messages as well as for streaming audio from those devices through the audio system in the vehicle.
The radio also contains a microcontroller and programming that allows it to communicate with other electronic modules in the vehicle over the Controller Area Network - Interior High Speed (CAN-IHS) data bus. Refer to COMMUNICATION, DESCRIPTION AND OPERATION .
The Uconnect® Hands Free Phone system components cannot be adjusted or repaired. If any Hands Free Phone system component is damaged or ineffective, that component must be replaced. The Hands Free Phone system software is flash programmable through the Universal Serial Bus (USB) port.
OPERATION
The Uconnect® Hands Free Phone system relies upon Bluetooth® technology to enable wireless connectivity between Bluetooth® compatible, paired and turned ON mobile devices and the on-board entertainment system components. This system also relies upon Advanced Speech Recognition (ASR) software to enable verbal commands to control the mobile device as well as the components and features of some other on-board systems.
The system will recognize up to ten Bluetooth® compatible devices, each of which is identified within the system by the name acquired from the device during the pairing process. The Hands Free Phone system will communicate with a paired device that is anywhere within the vehicle. However, covering the paired device with a metal object may block the signal.
The Hands Free Phone system is operated in one of two ways: actively or passively. Active operation begins with the vehicle operator pressing a push button on the left steering wheel switch pod on the left side of the Driver AirBag (DAB) trim cover in the center of the steering wheel. The Uconnect® Voice Recognition (VR ) button is pressed for hands free voice activated access to available features other than the phone, or the Uconnect® Phone (Phone identified by a phone handset icon) button is pressed for hands free phone access.
The VR or Phone button press provides a resistor multiplexed input to the BCM. The BCM is a gateway to the CAN-IHS data bus and sends an electronic switch press message over the CAN-IHS data bus to the radio.
When the radio receives the electronic switch press message, the radio suppresses any current audio output and issues an audible beep to indicate that the VR hardware is prepared to receive a verbal command. Part of the Uconnect® Hands Free Phone system hardware includes the VR microphones mounted in the headliner just above the driver and front passenger, one to each side of the headliner. The microphones provide a hardwired input of verbal commands to the VR engine within the radio, and the ASR software converts that input into an electronic instruction message broadcast over the CAN-IHS data bus to invoke the appropriate system response. If no appropriate verbal command is received within a few seconds following the audible beep , the system will provide an audible verbal output listing a menu of the available voice activation options.
Passive operation begins when an incoming cellular call is received. If the Bluetooth® phone is Short Message Service (SMS) text message capable and compatible with the Uconnect® + SiriusXM® Guardian system (see the Uconnect® web site), passive operation will also begin when an SMS text message is received. The call or SMS text message is relayed to the Bluetooth® transceiver embedded within the radio. The Bluetooth® transceiver then instructs the radio to announce the incoming call or message. The vehicle operator presses the Uconnect® Phone button in the steering wheel switch pod or the soft button that will appear in the radio display to accept the call or to accept the message.
The Bluetooth® transceiver connects the voices of the two phone parties using outputs through the audio system speakers and inputs through the Uconnect® hands free microphones. In the case of a text message, the Bluetooth® transceiver sends the message to the VR hardware and the ASR software converts the message from text to voice and plays it through the audio system speakers. The text message can then be replied to by pressing the Uconnect® VR button and giving an SMS verbal command to select from several predetermined short text phrase responses.
The Hands Free Phone system operates on battery current received through a fused B(+) circuit, but also monitors the ignition switch status through electronic messages received over the CAN-IHS data bus. If a call is in progress when the status of the ignition switch transitions to OFF, the system will continue to operate until the call has been completed.
The radio receives electronic message inputs over the CAN-IHS data bus related to the Hands Free Phone system. The radio is also connected to the CAN-C data bus; however, the radio is not a CAN gateway. All electronic message outputs of the radio are carried over the CAN-IHS data bus. When the radio monitors a problem in any of the audio system circuits and components, or in any of the Bluetooth® transceiver circuits, it stores a fault code or Diagnostic Trouble Code (DTC) in its memory circuit.
BLUETOOTH® PHONE
A compatible, customer-supplied and paired Bluetooth® phone is a required component of the hands free phone system. A list of suggested phones and providers is available at: https://www.driveuconnect.com
| Refer to COMPONENT INDEX . |
Outputs:
- Average calculated vehicle speed
- Average vehicle speed fault status
| Refer to COMPONENT INDEX . |
If the vehicle is equipped with satellite audio, a combined antenna for AM/FM and satellite and navigation is used. For AM/FM only, the antenna looks similar, but the base is smaller and is mounted in the same location.
The combination antenna consists of a Satellite Digital Audio Radio Service (SDARS) element, Global Positioning System (GPS) element, AM/FM element and a Long Term Evolution 1 (LTE1) element.
The audio system components are designed to provide audio entertainment and information through the reception, tuning and amplification of locally broadcast radio signals in both the Amplitude Modulating (AM) and Frequency Modulating (FM) commercial frequency ranges and other frequencies in export markets - AM/FM/SDARS NAFTA and MW/LW/DAB EMEA radio frequencies received.
| Refer to COMPONENT INDEX . |
When the hands-free VR control circuitry integral and internal to the radio detects the appropriate inputs or requests, it energizes the circuitry of the microphones mounted in the headliner just above the driver and front passenger, one to each side of the headliner. The microphones remain active until deactivated by the hands-free VR control circuitry, or until the status of the ignition transitions to OFF, whichever occurs first.
The inputs from the microphones are processed, filtered and redirected by the VR control circuitry and logic as appropriate. Those inputs can be redirected to the ASR engine or to the audio send circuitry of the Bluetooth® transceiver. Each of these electronic modules is also integral and internal to the radio.
| Refer to COMPONENT INDEX . |
The radio becomes operational when it receives a wake up signal over the CAN-C data bus indicating the status of the ignition switch is ON or Accessory. For additional information on the operation of the radio or media system in the vehicle, see the heading for the appropriate audio system option in the User Guide or the Owner Manual. See the Uconnect® web site (http://www.driveuconnect.com/ ) for more information, or refer to the For Owners link on the vehicle brand web site for copies of those publications.
The radio uses a roof mounted antenna for AM/FM signal reception and, depending upon vehicle optional equipment, a roof mounted combination antenna that can receive Global Positioning System (GPS) and satellite radio signals.
Depending upon the audio system options, the radio can play audio from many different media sources. The media can be played by connecting the source to the audio system via a 3.5 millimeter auxiliary (AUX) port, a USB port or through wireless Bluetooth® audio streaming. Refer to the Uconnect® web site (http://www.driveuconnect.com/ ) for compatibility information.
USB devices (for example, camera memory USB adaptors and others, excluding Apple products) must comply with the Mass Storage Device (MSD) standard. This remote USB port can provide power to the inserted device.
| Refer to COMPONENT INDEX . |
The three lower switches in the left steering wheel switch unit are normally open, resistor multiplexed momentary switches that are hardwired to the BCM through the steering wheel wire harness and the clockspring on the steering column. The BCM reads the remote radio switch inputs then sends the appropriate electronic messages to the radio over the CAN-IHS data bus to invoke the requested command.
The hardwired circuits between the remote radio switches and the BCM may be diagnosed using conventional diagnostic tools and procedures. Refer to the appropriate wiring information. The wiring information includes wiring diagrams, details of wire harness routing and retention, connector pin-out information and location views for the various wire harness connectors, splices and grounds. For proper wire repair, and connector repair procedures. Refer to STANDARD PROCEDURE . and. Refer to REMOVAL . Refer to INSTALLATION .
However, conventional diagnostic methods will not prove conclusive in the diagnosis of the Uconnect® switches or the electronic communication between modules that provide the features of the remote radio switches. The most reliable, efficient and accurate means to diagnose the remote radio switches or the electronic communication related to remote radio switch operation requires the use of a diagnostic scan tool. Refer to the appropriate diagnostic information.
| Refer to COMPONENT INDEX . |
The status of the Uconnect® + SiriusXM® Guardian™ Assist and SOS push buttons is relayed by the Local Interface Network (LIN) slave node integral to the rear view mirror via the LIN data bus to the BCM, which is a LIN master node. The BCM is also a CAN data bus gateway and relays the push button status information to the radio over the CAN-IHS data bus.