LEMON Manuals: Even more car manuals for everyone
Home >> Jeep >> 2012 >> Compass Limited, AWD, Standard >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Technical Service Bulletins >> Other Variant >> Engine Control Systems >> Flash: Powertrain Diagnostic And System Improvements (18-083-16)

Flash: Powertrain Diagnostic And System Improvements (18-083-16)

WARNING: This page is about the Compass Latitude, 2.0 A, which is a different variant/trim than selected.
Publication date: 2016-07-12
Reference number: 18-083-16
Supersedes refnos: 18-017-12

FLASH: POWERTRAIN DIAGNOSTIC AND SYSTEM IMPROVEMENTS

FLASH: POWERTRAIN DIAGNOSTIC AND SYSTEM IMPROVEMENTS

TECHNICAL SERVICE BULLETIN

Reference Number(s): 18-083-16, Date of Issue:  July 12, 2016
CHRYSLER: 2011 - 2012 Dodge Caliber (PM); 2011 - 2012 Jeep Compass/Patriot (MK)
GROUP: Vehicle Performance
Superceded Bulletin(s): 18-017-12, Date of Issue:  June 01, 2012
NOTE: THIS BULLETIN SUPERSEDES SERVICE BULLETIN 18-017-12, DATED JUNE 01, 2012, WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE HIGHLIGHTED WITH **ASTERISKS** AND INCLUDES AN ADDITIONAL DIAGNOSTIC TROUBLE CODE, SOFTWARE ENHANCEMENTS, VEHICLE INFORMATION UPDATES TO THE 2012 MY PM VEHICLES AND NEW LOP.

FOR HELP WITH USING wiTECH FOR ECU FLASH REPROGRAMMING, CLICK ON THE APPLICATION'S "HELP" TAB.

THE wiTECH SOFTWARE IS REQUIRED TO BE AT THE LATEST RELEASE BEFORE PERFORMING THIS PROCEDURE.

SUBJECT

Flash: Powertrain Diagnostic and System Improvements

OVERVIEW

This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software.

MODELS

MODELS CHART

2011 - 2012 (PM) Dodge Caliber
2011 - 2012 (MK) Jeep Compass/Patriot
NOTE: This bulletin applies to vehicles equipped with a 2.0L I4 DOHC 16V DUAL VVT Engine (Sales Codes ECN) or a 2.4L I4 DOHC 16V DUAL VVT Engine (Sales Code ED3).

SYMPTOM/CONDITION

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Code (DTC) has been set:

The following software enhancements are also available:

DIAGNOSIS

Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in TechCONNECT, verify all related systems are functioning as designed. If DTCs other than the one listed are present, record them on the repair order and repair as necessary before proceeding further with this bulletin.

If the customer describes the symptom/condition or if the technician finds the DTC, perform the REPAIR PROCEDURE .

REPAIR PROCEDURE

NOTE: Install a battery charger to ensure battery voltage does not drop below 13.2 volts. Do not allow the charging voltage to climb above 13.5 volts during the flash process.
NOTE: If this flash process is interrupted/aborted, the flash should be restarted.
  1. Reprogram the PCM with the latest available software. Detailed instructions for flashing control modules using the wiTECH Diagnostic Application are available by selecting the application's "HELP" tab.
  2. Clear all DTCs that may have been set in any module due to reprogramming. The wiTECH application will automatically present all DTCs after the flash and allow them to be cleared.

POLICY

Reimbursable within the provisions of the warranty.

TIME ALLOWANCE

TIME ALLOWANCE CHART

Labor Operation No: Description Skill Category Amount
**18-19-06-LB Module, Powertrain Control (PCM) - Reprogram (0 - Introduction) 1 - Engine Repair And Performance 0.2 Hrs.**
NOTE: The expected completion time for the flash download portion of this procedure is approximately 2 minutes. Actual flash download times may be affected by vehicle connection and network capabilities.

FAILURE CODE

The dealer must choose which failure code to use. If the customer came in with an issue and if the dealer finds a software update to correct that issue, use failure code CC, for all other use failure code RF. 

FAILURE CODE

CC Customer Concern
RF Routine Flash