| U0147 |
Radio Head Unit |
Lost Communication With Gateway "B" |
- Radio head unit, gateway module - no response (D2B/MOST)
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check radio head unit to gateway module control and power circuit`s, install a new module as required, refer to DTC Index |
| U0193 |
Gateway module |
Lost Communication with Digital Audio Control Module A Satellite Radio Module |
- Gateway module - lost communication with satellite radio module
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check satellite radio module power and bus circuit to gateway module on MOST ring |
| U0194 |
Gateway module |
Lost Communication with Digital Audio Control Module B Digital Audio Broadcast Module |
- Gateway module - lost communication with digital audio broadcast module
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check digital audio broadcast module power and bus circuit to gateway module on MOST ring |
| U0237 |
Gateway module |
Lost Communication with Digital Audio Control Module C IBOC In Band On Channel / HD Radio |
- Gateway module - lost communication with Digital Audio Control Module C
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check Digital Audio Control Module C power and bus circuit to gateway module on MOST ring |
| U1041 |
Generic Electronic Module |
SCP (J1850) invalid or missing data for vehicle speed |
- Data in the speed signal message is missing or outside of normal limits
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check for SCP network wire broken, or short circuit to power or ground. Repair wiring harness using approved materials and methods. Clear DTC and retest system to ensure correct operation. |
| U1135 |
Generic Electronic Module |
SCP (J1850) invalid or missing data for ignition switch/starter |
- Data in the ignition signal message is missing or outside of normal limits
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check for SCP network wire broken, or short circuit to power or ground. Repair wiring harness using approved materials and methods. Clear DTC and retest system to ensure correct operation. |
| U1147 |
Generic Electronic Module |
SCP (J1850) invalid or missing data for vehicle security |
- Data in the security key message is missing or outside of normal limits
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check for SCP network wire broken, or short circuit to power or ground. Repair wiring harness using approved materials and methods. Clear DTC and retest system to ensure correct operation. |
| U1262 |
Radio Head Unit |
SCP (J1850) Communication Bus Fault |
- Radio head unit, ECU not responding - internal standard corporate protocol (SCP) chip failure
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check radio head unit SCP circuit for fault, suspect the radio head unit, install a new module as required, refer to DTC Index |
| U1262 |
Generic Electronic Module |
SCP (J1850) communication bus fault |
- Missing message
- Wiring harness concern
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check for SCP network wire broken. Repair wiring harness using approved materials and methods. Clear DTC and retest system to ensure correct operation. |
| U1900 |
Climate Control System - General Information |
CAN Communication Bus Fault - Receive Error |
- Communication on CAN network fault
|
Refer to the relevant wiring diagram and check the CAN bus wiring for open circuits, shorts to power or ground. Check termination resistance is correct. Repair harness as required using approved harness repair kit |
| U1900 |
Instrument Cluster |
CAN communication bus fault - receive error |
- Instrument cluster, missing messages on CAN bus
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check instrument cluster CAN bus circuit for faults |
| U1A15 |
Gateway module |
Incomplete MOST Ring Reported By ICM |
- Gateway module - (MOST) ring break
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check (MOST) circuit for ring break |
| U2003 |
Radio Head Unit |
Audio Compact Disk / Disk Jockey Unit is Not Responding |
- Radio head unit, CD multi-changer - no response(D2B)
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check cd multi-changer module and D2B circuit for fault, install a new module as required, refer to DTC Index |
| U2008 |
Radio Head Unit |
Audio Phone Not Responding |
- Radio head unit, telephone control module - no response(D2B)
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check telephone control module and D2B circuit for fault, install a new module as required, refer to DTC Index |
| U2019 |
Radio Head Unit |
Audio Voice Module Not Responding |
- Radio head unit, audio voice module - no response(D2B)
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check audio voice module and D2B circuit for fault, install a new module as required, refer to DTC Index |
| U2196 |
Instrument Cluster |
Invalid engine RPM data |
- Instrument cluster receive CAN bus message with default data for > 1 second
|
Check dynamic stability control module for stored DTCs |
| U2197 |
Instrument Cluster |
Invalid vehicle speed data |
- Instrument cluster receive CAN bus message with default data for > 1 second
|
Check dynamic stability control module for stored DTCs |
| U2199 |
Instrument Cluster |
Invalid engine coolant temperature data |
- Instrument cluster, missing messages on CAN bus
|
Check engine control module for stored DTCs |
| U2200 |
Instrument Cluster |
Invalid ODO count data |
- Instrument cluster, missing messages on CAN bus
|
Check dynamic stability control module for stored DTCs |
| U2510 |
Instrument Cluster |
CAN-invalid data for vehicle security |
- (LED flash 23) instrument cluster, engine control module PATS identification wrong/mismatch with cluster
|
Enable engine control module PATS identification transfer to instrument cluster using the manufacturer approved diagnostic system |
| U2511 |
Instrument Cluster |
CAN-data mismatch |
- (LED flash 23) Instrument cluster, engine control module PATS identification wrong/mismatch with cluster
|
Enable engine control module PATS identification transfer to instrument cluster using the manufacturer approved diagnostic system |
| U2514 |
Generic Electronic Module |
Missing message for vehicle speed |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, Check SCP network for open circuit. Repair wiring harness using approved methods and materials. Clear DTC and retest to ensure correct operation. |
| U2601 |
Gateway module |
(D2B)Wake-up Line Short to Ground |
- Gateway module - wake-up line short to ground
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check gateway module (D2B) wake-up line for short to ground |
| U2601 |
Radio Head Unit |
(D2B)Wake-up Line Short To Ground |
- Radio head unit, gateway module - wake-up line short to ground
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check gateway module (D2B) wake-up line for short to ground |
| U2601 |
Voice Activated Control Module |
D2B wake up - short to ground |
- Voice activated control module
- Wake up line short to ground
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check D2B wake up circuit for shorts to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| U2602 |
Radio Head Unit |
Incomplete MOST Ring (fault report received) |
- Radio head unit - (MOST) ring circuit fault
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Check radio head unit for most ring circuit fault |
| U2603 |
Radio Head Unit |
Incomplete MOST Ring (No Fault Report Received) |
- Radio head unit - (MOST) ring circuit fault
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Check (MOST) ring for circuit fault |
| U2604 |
Radio Head Unit |
Incomplete MOST Ring (Corrupted Fault Report Received) |
- Radio head unit - (MOST) ring circuit fault
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check (MOST) ring for circuit fault |
| U2605 |
Radio Head Unit |
Master ECU Unable To Initialize It's Address |
- Radio head unit - (MOST) ring circuit fault (more than one master on the MOST ring)
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check for configuration fault on (MOST) ring modules. Install a new module as required, refer to DTC Index |
| U2606 |
Radio Head Unit |
Slave ECU Unable To Initialize It's Address |
- Radio head unit - (MOST) ring circuit fault slave ECU configuration fault
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check for configuration fault on (MOST) ring modules. Install a new module as required, refer to DTC Index |
| U2607 |
Radio Head Unit |
Slave ECU ( switched into bypass mode) |
- Radio head unit - (MOST) ring circuit fault (slave ECU configuration fault)
|
The module can be configured using the new module procedure. Check and configure as required |
| U2609 |
Gateway module |
(D2B)Wake-up pulse width out of spec |
- Gateway module - wake-up line fault (pulse< 50mS, pulse > 110mS)
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check gateway module (D2B) wake-up line circuit for fault |
| U2609 |
Radio Head Unit |
(D2B)Circuit Wake-up Line (pulse width out of spec) |
- Radio head unit - wake up line circuit fault (pulse< 50mS, pulse > 110mS)
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check radio head unit(D2B) wake up line circuit for fault |
| U2609 |
Voice Activated Control Module |
D2B wake up - pulse width out of spec |
- Voice activated control module wake up line - circuit fault (pulse <50mS - pulse >110mS)
|
Refer to appropriate SYSTEM WIRING DIAGRAMS and notes, check voice activated control module D2B wake up line circuit for faults. Repair any defects, clear DTC and retest to confirm correct operation. |
| U2610 |
Gateway module |
(D2B) Slave ECU fails to receive a report position |
- Gateway module - during initialization no position status report is received from one or more slave modules
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check (D2B) slave modules and circuit for fault, replace as required, refer to DTC Index |
| U2610 |
Voice Activated Control Module |
D2B slave ECU fails to receive a report position |
- During initialization no position status report is received from one or more slave modules
|
Carry out any pin point tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check D2B slave modules and circuit for faults. Replace as required, refer to DTC Index
. Repair any defects, clear DTC and retest to confirm correct operation. |
| U2611 |
Gateway module |
(D2B) Slave ECU fails to receive an alarm clear command |
- Gateway module - on entering alarm state, slave ECU has failed to receive alarm clear command
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check (D2B) slave modules and circuit for fault, replace as required, refer to DTC Index |
| U2611 |
Voice Activated Control Module |
D2B slave ECU fails to receive an alarm clear command |
- Voice activated control module - on entering alarm state, slave ECU has failed to receive alarm clear command
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check D2B slave modules and circuit for faults. Replace as required, refer to DTC Index
. Repair any defects, clear DTC and retest to confirm correct operation. |
| U2613 |
Radio Head Unit |
Navigation Module Not Responding on D2B |
- Radio head unit - no response from navigation module
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Check navigation module to front audio control module circuit |
| U2614 |
Radio Head Unit |
Amp Module Not Responding on D2B |
- Radio head unit - no response from audio amplifier module
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Check audio amplifier module to front audio control module circuit |
| U300004 |
Digital Audio Broadcast Module |
Control module |
|
Install a new digital audio broadcast module |
| U30004A |
Digital Audio Broadcast Module |
Control module |
- Incorrect component installed
|
Install a new digital audio broadcast module or reconfigure the digital audio broadcast module using the manufacturer approved diagnostic system |
| U300055 |
Digital Audio Broadcast Module |
Control module |
- Incorrect car configuration file data received
|
Check/update car configuration file using manufacturer approved diagnostic system |
| U300087 |
Digital Audio Broadcast Module |
Control module |
|
Check GEM for DTCs and refer to DTC Index
. Check information and entertainment module for car configuration file and MOST network DTCs and refer to relevant DTC Index
. Carry out MOST/CAN network tests using the manufacturer approved equipment. |
| U300098 |
Digital Audio Broadcast Module |
Control module |
- Component or system over temperature
|
Check for additional DTCs and refer to relevant DTC Index
, check/monitor system for reoccurrence |
| U300362 |
Digital Audio Broadcast Module |
Battery voltage |
- Mis-match in battery voltage of 2 volts or more between digital broadcast module and GEM
|
Refer to appropriate SYSTEM WIRING DIAGRAMS and check power distribution to the DAB module and GEM. Repair any wiring faults using approved materials and methods. Clear DTCs and test system to ensure correct operation. |
| U3004 |
Gateway module |
Digital Tuner (Most slave) Internal fault |
- Gateway module - digital tuner MOST slave module is inoperative
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check digital tuner module replace as required, refer to DTC Index |
| U3098 |
Gateway module |
Digital Tuner (Most slave) Over temperature |
- Gateway module - digital tuner (Most slave) is hot
|
Check digital tuner module and location for causes of excessive temperature, install a new module as required, refer to DTC Index |