DTC Index (B, C, P, U Codes - With Testing): B-Codes
| DTC | System | Description | Possible Source | Action |
|---|---|---|---|---|
| B1041 | Generic Electronic Module | Direction indicator power feed fuse blown |
|
Check power distribution box fuses, if blown refer to appropriate SYSTEM WIRING DIAGRAMS and check for short circuits to ground on indicator circuits. Repair wiring harness and fit replacement fuses as required. Clear DTC and retest system to ensure correct operation. |
| B11A4 | Gateway module | DAB L Band Antenna |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check (digital audio broadcast L band) antenna circuit for short to power, ground or open circuit |
| B11A411 | Digital Audio Broadcast Module | L-Band antenna |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS and check DAB L-band antenna circuit for short to ground |
| B11A413 | Digital Audio Broadcast Module | L-Band antenna |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS and check DAB L-band antenna circuit for open circuit |
| B11A5 | Gateway module | DAB Band 3 Antenna |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check (digital audio broadcast band 3) antenna circuit for short to power, ground or open circuit |
| B11A511 | Digital Audio Broadcast Module | Band 3 antenna |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS and check DAB band 3 antenna circuit for short to ground |
| B11A513 | Digital Audio Broadcast Module |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS and check DAB band 3 antenna circuit for open circuit | |
| B1200 | Climate Control System - General Information | Climate Control Push-button Circuit Failure |
|
Check for objects pressing against the control buttons. Check for contamination of the buttons which could cause them to stick. (E.g.: spilt food or drink) If there are no apparent external reasons for a button to stick - then suspect an internal fault and install a new combined Climate Control panel/electronic control unit as required. Clear the DTC and recheck operation of system to ensure the DTC does not reset after 5 minutes |
| B1202 | Instrument Cluster | Fuel sender circuit failure |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check the rear electronic module, fuel sender circuit for open circuit. |
| B1202 | Fuel Tank and Lines | Fuel level sensor 1 circuit fault |
|
For fuel level sensor circuit tests, Refer to Pinpoint Test A . |
| B1204 | Instrument Cluster | Fuel sender circuit short to ground |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check the rear electronic module, fuel sender circuit for short to ground. |
| B1204 | Fuel Tank and Lines | Fuel level sensor 1 circuit fault |
|
For fuel level sensor circuit tests, Refer to Pinpoint Test A . |
| B1205 | Instrument Cluster | EIC switch-1 assembly circuit failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check instrument cluster, auxiliary lighting switch pack for circuit fault |
| B1213 | Instrument Cluster | Anti-theft number of programmed keys is below minimum |
|
Count number of stored keys using the manufacturer approved diagnostic system. Add keys as required. |
| B1231 | Supplemental Restraint System | Crash data memory full |
|
Please check part is not on any form of prior authorization before replacement. |
| B1238 | Gateway module | High Temperature |
|
Check gateway module and location for causes of excessive temperature, install a new gateway module as required, refer to DTC Index |
| B1238 | Radio Head Unit | Over Temperature Fault |
|
Check cd multi-changer module and location for causes of excessive temperature, install a new module as required, refer to DTC Index |
| B1239 | Climate Control System - General Information | Air Flow Blend Door Driver Circuit Failure |
NOTE:
Fault is checked for while the motor is running.
|
NOTE:
Check that the blend door is not mechanically jammed by a foreign body inside the air distribution housing Refer to the electrical circuit diagrams and check the integrity of the wiring between the blend door actuator motor and the climate control ECU. Check the motor power feed line for short to ground. Check the four control lines for open/short circuits. If no wiring defects are found install a new actuator motor. Clear the DTC and recheck that the DTC does not reset by operating the system |
| B1242 | Climate Control System - General Information | Air Flow Recirculation Door Driver Circuit Failure |
NOTE:
Fault is checked for when the motor is not running.
|
NOTE:
Check that the recirculation door is not mechanically jammed by a foreign body inside the air distribution housing Refer to the electrical circuit diagrams and check the integrity of the wiring between the recirculation door actuator motor and the climate control ECU. Check both control lines for open/short circuits. If no wiring defects are found install a new actuator motor. Clear the DTC and recheck that the DTC does not reset by operating the system |
| B1251 | Climate Control System - General Information | Air Temperature Internal Sensor Circuit Open |
|
Refer to the relevant circuit diagram and check the integrity of the wiring between the air temperature internal sensor and the Climate Control System ECU. Check for open circuits on the in car Sensor Input and Sensor Ground lines between the sensor and the Climate Control ECU. If no wiring defects are found install a new Air Temperature Internal Sensor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B1253 | Climate Control System - General Information | Air Temperature Internal Sensor Circuit Short to Ground |
|
Refer to the relevant circuit diagram and check the integrity of the wiring between the air temperature internal sensor and the Climate Control System ECU. Check for short circuits to ground on the Incar Sensor Input line between the sensor and the Climate Control ECU. If no wiring defects are found install a new Air Temperature Internal Sensor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B1255 | Climate Control System - General Information | Air Temperature External Sensor Circuit Open |
|
Refer to the relevant circuit diagram and check the integrity of the wiring between the air temperature external sensor and the Climate Control System ECU. Check for open circuits on the Ambient Sensor line and the Sensor Ground line between the sensor and the Climate Control ECU. If no wiring defects are found install a new Ambient Temperature External Sensor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B1257 | Climate Control System - General Information | Air Temperature External Sensor Circuit Short To Ground |
|
Refer to the relevant circuit diagram and check the integrity of the wiring between the air temperature external sensor and the Climate Control System ECU. Check for shorts to ground on the Ambient Sensor line between the sensor and the Climate Control ECU. If no wiring defects are found install a new Ambient Temperature External Sensor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B1261 | Climate Control System - General Information | Solar Radiation Sensor Circuit Short To Ground |
|
This component is not fitted after 2005 model year. The circuit should be open in vehicles after 2005my |
| B1262 | Climate Control System - General Information | Servo Motor Defrost Circuit Failure |
NOTE:
Fault is checked for while the motor is running
|
NOTE:
Check that the defrost door is not mechanically jammed by a foreign body inside the air distribution housing Refer to the relevant circuit diagram and check the integrity of the wiring between the Defrost Door Servo motor and the Climate Control System ECU. Check the Defrost Power line for a short to ground. Check each of the four control lines for open circuits, or shorts to power or ground. If no wiring defects are found install a new Defrost Door actuator motor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B1263 | Climate Control System - General Information | Panel Door Circuit Failure |
NOTE:
Fault is checked for while the motor is running
|
NOTE:
Check that the panel door is not mechanically jammed by a foreign body inside the air distribution housing Refer to the relevant circuit diagram and check the integrity of the wiring between the Panel Door Servo motor and the Climate Control System ECU. Check the Panel/Floor Power line for a short to ground. Check each of the four control lines for open circuits, or shorts to power or ground. If no wiring defects are found install a new Panel/floor actuator motor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B1298 | Generic Electronic Module | Power supply sensor circuit short to battery |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check intrusion and inclination sensor circuits for short to power. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1299 | Parking Aid | Power Supply Sensor Circuit Short To Ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check parking aid module rear sensor power circuit for short to ground. Repair wiring harness using approved methods and materials, clear DTC and retest system to confirm correct operation. |
| B1299 | Generic Electronic Module | Power supply sensor circuit short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check intrusion and inclination sensor circuits for short to ground. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1315 | Generic Electronic Module | Battery saver relay coil circuit short to battery |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, battery saver relay coil circuits for short to power. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. Replace relay as required, clear DTC and retest system to ensure correct operation. |
| B1317 | Climate Control System - General Information | Battery voltage high |
|
Check charging system Refer to Charging System - 2.0L/2.5L/3.0L article. |
| B1317 | Instrument Cluster | Battery voltage high |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes, and check instrument cluster, power supply for voltage fault. |
| B1317 | Supplemental Restraint System | Battery voltage high |
|
Suspect charging system fault. Refer to charging system tests. |
| B1318 | Climate Control System - General Information | Battery Voltage Low |
|
Check battery is fully charged. Using the appropriate circuit diagrams: Check power supply circuits from front power distribution box to the fuel fired heater unit. Using the appropriate circuit diagrams: check ground connections to the fuel fired heater unit. Repair any wiring faults using the approved harness repair kit. Clear the DTC and test the system to verify the repair. Check charging system, refer to Charging System - 2.0L/2.5L/3.0L article. |
| B1318 | Instrument Cluster | Battery voltage low |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes, and check instrument cluster, power supply for voltage fault. |
| B1318 | Exterior Lighting | Battery voltage low |
|
Battery voltage low, check charging system for faults. Charge level is controlled by engine control module. |
| B1318 | Supplemental Restraint System | Battery voltage low |
|
Suspect charging system fault. Refer to charging system tests. |
| B1342 | Climate Control System - General Information | ECU is Faulted |
|
Check the battery is fully charged and the supply leads are correctly connected. Refer to the relevant circuit diagram and check the integrity of the wiring between the Climate Control ECU and Power and ground distribution components. Check the power supply lines and fuses for open circuits and volt drops. Check the ground connections for open circuits and volt drops. Repair power supply and ground connections as required. Clear the DTC and operate the system to check if the DTC does reset. If the DTC is reset install a new Climate Control ECU. |
| B1342 | Instrument Cluster | ECU is faulted |
|
Suspect instrument cluster module, check and install a new instrument cluster as required, refer to DTC Index . |
| B1342 | Exterior Lighting | ECU is faulted |
|
Detectable internal defect (RAM/EEPROM error), check module for external connection problems, replace module as required. |
| B1342 | Parking Aid | ECU Is Faulted |
|
Suspect faulty module, check and install as required, refer to DTC Index |
| B1342 | Gateway module | Internal failure in Gateway module |
|
Internal failure install a new gateway module as required, refer to DTC Index |
| B1342 | Radio Head Unit | ECU Internal Failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check Radio head unit radio functions for fault, replace as required, refer to DTC Index |
| B1342 | Navigation System | ECU is defective |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. check navigation system module for internal failure. Install a new module as required, refer to DTC Index . |
| B1342 | Supplemental Restraint System | RCM internal fault |
|
Please check part is not on any form of prior authorization before replacement. |
| B1359 | Instrument Cluster | Ignition run/Acc circuit failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check instrument cluster, ignition power and ground for circuit faults. |
| B1438 | Generic Electronic Module | Wiper mode select switch circuit failure |
|
Inspect switch for signs of damage or incorrect operation or sticking, replace switch as required. Check wiper control switch circuits for open circuits, shorts to power or ground. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1446 | Generic Electronic Module | Wiper park sense circuit failure |
|
Inspect wiper motor harness for damage, Refer to appropriate SYSTEM WIRING DIAGRAMS and check wiper motor circuits for open circuits, shorts to ground or power. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1450 | Generic Electronic Module | Wiper wash/delay switch circuit failure |
|
Check wiper wash/delay switch for correct operation. Refer to appropriate SYSTEM WIRING DIAGRAMS, check wiper control circuits for short to battery. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1499 | Generic Electronic Module | Lamp turn signal left circuit failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check left turn signal circuit for open circuits or short to ground. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1503 | Generic Electronic Module | Lamp turn signal right circuit failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check right turn signal circuit for open circuits or short to ground. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1549 | Generic Electronic Module | Power window master circuit short to battery |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, power window master circuit for short to power. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1550 | Generic Electronic Module | Power window master circuit short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, power window master circuit for short to ground. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1553 | Generic Electronic Module | Deck lid release circuit short to battery |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check deck lid release circuit for short to power. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1554 | Generic Electronic Module | Deck lid release circuit short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check deck lid release circuit for short to ground. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1570 | Generic Electronic Module | Lamp headlamp high-beam circuit short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, headlamp high beam circuit for short to ground. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B1600 | Instrument Cluster | PATS ignition key transponder signal not received |
|
Carry out any pinpoint test associate with this DTC using the manufacturer approved diagnostic system. Check for transponder key fault |
| B1601 | Instrument Cluster | PATS received incorrect key-code from ignition key transponder |
|
Carry out any pinpoint test associate with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS and notes, check transponder key is programmed to the vehicle |
| B1602 | Instrument Cluster | PATS received invalid format of key-code from ignition key transponder |
|
Carry out any pinpoint test associate with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check instrument cluster communication to PATS transceiver module circuit for faults. |
| B1676 | Climate Control System - General Information | Battery Pack Voltage Out Of Range |
|
Check the battery is fully charged and the supply leads are correctly connected. Refer to the relevant circuit diagram and check the integrity of the wiring between the Climate Control ECU and the Front Power Distribution Box and ground distribution components. Check the power supply lines and fuses for open circuits and volt drops. Check the ground connections for open circuits and volt drops. Repair power supply and ground connections as required. |
| B1676 | Anti-Lock Control - Stability Assist | Battery voltage out of range: 9 - 16 volts |
|
For charging system tests, Refer to Charging System - 2.0L/2.5L/3.0L and . Please check part is not on any form of prior authorization before replacement. |
| B1681 | Instrument Cluster | PATS transceiver module signal is not received |
|
Carry out any pinpoint test associate with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check PATS transceiver module for fault |
| B1823 | Generic Electronic Module | Wiper rear park sense input circuit open |
|
Rear wiper park sense switch not detected for 4 seconds. Refer to appropriate SYSTEM WIRING DIAGRAMS and check rear wiper circuits for open circuits, short to power or short to ground. Repair wiring harness using approved materials and methods. Clear DTC and retest system to ensure correct operation. |
| B1870 | Supplemental Restraint System | Airbag MIL circuit fault |
|
For MIL circuit tests, Refer to Pinpoint Test A . |
| B1884 | Supplemental Restraint System | Passenger airbag deactivated (PAD) indicator lamp circuit fault |
|
For PAD circuit tests, Refer to Pinpoint Test B . |
| B1890 | Supplemental Restraint System | Passenger airbag deactivated (PAD) indicator lamp circuit fault |
|
For PAD circuit tests, Refer to Pinpoint Test B . |
| B1921 | Supplemental Restraint System | RCM internal airbag diagnostic monitor ground circuit fault |
|
WARNING:
To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any air bag SRS components. To deplete the backup power supply energy, disconnect the battery ground cable and wait for one minute. Failure to follow this instruction may result in personal injury. Ensure a clean electrical contact between the RCM and ground. Ensure the fasteners are correctly torqued. |
| B1946 | Climate Control System - General Information | Climate Control A/C Post Evaporator Sensor Circuit Failure |
|
Refer to the relevant circuit diagram and check the integrity of the wiring between the Climate Control A/C Post Evaporator Sensor and the Climate Control System ECU. Check for open circuits on the EVAP Sensor line between the sensor and the Climate Control ECU. Check the sensor ground line for open circuits. If no wiring defects are found install a new Climate Control A/C Post Evaporator Sensor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B1947 | Climate Control System - General Information | Climate Control A/C Post Evaporator Sensor Circuit Short To Ground |
|
Refer to the relevant circuit diagram and check the integrity of the wiring between the Climate Control A/C Post Evaporator Sensor and the Climate Control System ECU. Check for short circuits to ground on the EVAP Sensor line between the sensor and the Climate Control ECU. If no wiring defects are found install a new Climate Control A/C Post Evaporator Sensor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B1A89 | Gateway module | SDARS or Digital Tuner Antenna |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check satellite radio module or digital tuner antenna circuit for short to power, ground or open circuit |
| B2004 | Radio Head Unit | Internal Media Over Temperature Fault |
|
Check Radio head unit and location for causes of excessive temperature, install a new module as required, refer to DTC Index |
| B2090 | Generic Electronic Module | Remote key entry data line failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check RKE data line for short to ground. Repair wiring harness, clear DTC and retest system to ensure correct operation. |
| B2091 | Generic Electronic Module | Remote key communication failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check RKE data line for short to battery. Repair wiring harness, clear DTC and retest system to ensure correct operation. |
| B2103 | Instrument Cluster | Antenna not connected |
|
Carry out any pinpoint test associate with this DTC using the manufacturer approved diagnostic system. Check other modules for related DTCs. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check instrument cluster circuit to PATS transceiver for fault. |
| B2108 | Generic Electronic Module | Front wiper short to battery |
|
Inspect from wiper motor relay, replace as required. Refer to appropriate SYSTEM WIRING DIAGRAMS, check wiper relay circuit for short to power. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2111 | Generic Electronic Module | Front wiper short to ground |
|
Inspect from wiper motor relay, replace as required. Refer to appropriate SYSTEM WIRING DIAGRAMS, check wiper relay circuit for short to ground. Repair faults using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2114 | Generic Electronic Module | Front washer input short to ground |
|
Check front washer switch operation for sticking. Replace switch as required. Refer to appropriate SYSTEM WIRING DIAGRAMS. Check washer input circuit for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2141 | Instrument Cluster | NVM configuration failure |
|
Carry out any pinpoint test associate with this DTC using the manufacturer approved diagnostic system. Enter vehicle ID into the instrument cluster (Enable PCM ID transfer) using the manufacturer approved diagnostic system. |
| B2143 | Instrument Cluster | NVM memory failure |
|
Carry out any pinpoint test associate with this DTC using the manufacturer approved diagnostic system. Suspect instrument cluster internal failure. Clear DTC carry out battery reset, if DTC returns suspect instrument cluster internal failure, check and replace as required. Refer to DTC Index |
| B2177 | Generic Electronic Module | Interior scanning sensor circuit failure |
|
Check sensor is present and appears undamaged. Refer to appropriate SYSTEM WIRING DIAGRAMS. Check sensor circuit for open circuits, short to power or ground. Replace sensor as required, repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2197 | Navigation System | TV module error |
|
Carry out any pinpoint tests associated with this DTC using the manufacturers approved diagnostic equipment. Check the satellite navigation system module for failure. Install a new module as required, refer to DTC Index . |
| B2198 | Navigation System | Traffic Master module error |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation system module communication circuit to traffic master module for failure. install a new module as required, refer to DTC Index . |
| B2199 | Navigation System | VICS Module Error |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation system module communication circuit to vehicle information control system module for faults. install a new module as required, refer to DTC Index . |
| B2201 | Navigation System | No communication with traffic master module |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation system module communication circuit to traffic master module for a fault. Install a new module as required, refer to DTC Index . |
| B2202 | Navigation System | No communication to VICS module |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation system module communications circuit to vehicle information control module for faults. |
| B2204 | Navigation System | GPS Antenna connection open or short |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation system module (GPS) antenna for open or short circuit. |
| B2205 | Navigation System | GPS receiver fault |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to the appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation system module global positioning satellite (GPS) antenna circuit. Check the antenna is not obstructed (vehicle must be outside when being tested). Replace module is fault persists. |
| B2206 | Navigation System | Gyroscope fault |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation system module for faults. Install a new module as required, refer to DTC Index . |
| B2207 | Parking Aid | ECU ROM Checksum Error |
|
Suspect faulty module, check and install as required, refer to DTC Index |
| B2207 | Navigation System | Internal ECU ROM checksum fault |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check the navigation system module for faults. Install a new module as required, refer to DTC Index . |
| B2208 | Navigation System | Navigation module to display and switch module communication error |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation system display and switch module communication circuit for fault |
| B2258 | Generic Electronic Module | Headlamp washer relay circuit short to battery |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check headlamp washer relay circuits for open circuits, short to power or ground. Repair any faults found using approved methods and materials. Replace relay as required. Clear DTC and retest system to confirm correct operation. |
| B2281 | Generic Electronic Module | Right turn switch short to ground |
|
Check right turn switch operation for sticking. Replace switch as required. Refer to appropriate SYSTEM WIRING DIAGRAMS. Check right turn switch input circuit for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2282 | Generic Electronic Module | Left turn switch short to ground |
|
Check left turn switch operation for sticking. Replace switch as required. Refer to appropriate SYSTEM WIRING DIAGRAMS. Check left turn switch input circuit for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2283 | Generic Electronic Module | Turn signal chime short to battery |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS. Check ECU output circuit to the steering column speaker for short to power. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2284 | Generic Electronic Module | Turn signal chime short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS. Check ECU output circuit to the steering column speaker for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2287 | Generic Electronic Module | Inclination sensor circuit failure |
|
Inspect vehicle for presence of and condition of inclination sensor. Replace sensor if required. Refer to appropriate SYSTEM WIRING DIAGRAMS. Check inclination sensor circuits for open circuits or short to power or ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2290 | Supplemental Restraint System | Occupant classification sensor (OCS) system fault |
|
Check the power and ground to the module, Refer to Pinpoint Test N . Please check part is not on any form of prior authorization before replacement. |
| B2290 | Supplemental Restraint System | Occupant classification sensor (OCS) system fault |
|
For communication circuit tests, Refer to Pinpoint Test N . For more detailed CAN circuit tests, Refer to Communications Network . |
| B2290 | Supplemental Restraint System | Occupant classification sensor (OCS) system fault |
|
Check that the OCS is the correct unit for the vehicle. Please check part is not on any form of prior authorization before replacement. |
| B2290 | Supplemental Restraint System | Occupant classification sensor (OCS) system fault |
|
Install a new OCS, See Occupant Classification Sensor . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt pretensioner circuit fault |
|
For driver side pretensioner circuit tests, Refer to Pinpoint Test A . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt pretensioner circuit fault |
|
For driver side pretensioner circuit tests, Refer to Pinpoint Test A . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt pretensioner circuit fault |
|
For driver side pretensioner circuit tests, Refer to Pinpoint Test A . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt pretensioner circuit fault |
|
For driver side pretensioner circuit tests, Refer to Pinpoint Test A . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt pretensioner circuit fault |
|
For passenger side pretensioner circuit tests, Refer to Pinpoint Test B . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt pretensioner circuit fault |
|
For passenger side pretensioner circuit tests, Refer to Pinpoint Test B . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt pretensioner circuit fault |
|
For passenger side pretensioner circuit tests, Refer to Pinpoint Test B . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt pretensioner circuit fault |
|
For passenger side pretensioner circuit tests, Refer to Pinpoint Test B . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt reel pretensioner circuit fault |
|
For driver side reel pretensioner circuit tests, Refer to Pinpoint Test E . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt reel pretensioner circuit fault |
|
For driver side reel pretensioner circuit tests, Refer to Pinpoint Test E . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt reel pretensioner circuit fault |
|
For driver side reel pretensioner circuit tests, Refer to Pinpoint Test E . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt reel pretensioner circuit fault |
|
For driver side reel pretensioner circuit tests, Refer to Pinpoint Test E . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt reel pretensioner circuit fault |
|
For passenger side reel pretensioner circuit tests, Refer to Pinpoint Test F . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt reel pretensioner circuit fault |
|
For passenger side reel pretensioner circuit tests, Refer to Pinpoint Test E . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt reel pretensioner circuit fault |
|
For passenger side reel pretensioner circuit tests, Refer to Pinpoint Test F . |
| B2292 | Supplemental Restraint System - Safety Belt System | Safety belt reel pretensioner circuit fault |
|
For passenger side reel pretensioner circuit tests, Refer to Pinpoint Test F . |
| B2293 | Supplemental Restraint System | Airbag circuit status fault |
|
For airbag circuit tests, Refer to Pinpoint Test C . |
| B2293 | Supplemental Restraint System | Airbag circuit status fault |
|
For airbag circuit tests, Refer to Pinpoint Test C . |
| B2294 | Supplemental Restraint System | Curtain airbag circuit status fault |
|
For curtain airbag circuit tests, Refer to Pinpoint Test D . |
| B2294 | Supplemental Restraint System | Curtain airbag circuit status fault |
|
For curtain airbag circuit tests, Refer to Pinpoint Test D . |
| B2295 | Supplemental Restraint System | Side airbag circuit status fault |
|
For side airbag circuit tests, Refer to Pinpoint Test E . |
| B2295 | Supplemental Restraint System | Side airbag circuit status fault |
|
For side airbag circuit tests, Refer to Pinpoint Test E . |
| B2296 | Supplemental Restraint System | Front impact sensor circuit status fault |
|
For front impact sensor circuit tests, Refer to Pinpoint Test F . |
| B2296 | Supplemental Restraint System | Front driver side impact sensor circuit status fault |
|
For front driver side impact sensor circuit tests, Refer to Pinpoint Test G . |
| B2296 | Supplemental Restraint System | Front passenger side impact sensor circuit status fault |
|
For front passenger side impact sensor circuit tests, Refer to Pinpoint Test H . |
| B2296 | Supplemental Restraint System | Impact sensor circuit status fault |
|
For rear driver side impact sensor circuit tests, Refer to Pinpoint Test I . |
| B2296 | Supplemental Restraint System | Impact sensor circuit status fault |
|
For rear passenger side impact sensor circuit tests, Refer to Pinpoint Test J . |
| B2308 | Climate Control System - General Information | Interior Air Temperature Inlet Motor Failure |
|
Check the air inlet path is clear and no foreign objects are present in the air intake orifice. Check the integrity of the wiring between the Interior Air Temperature Sensor Aspirator Motor and the power distribution components. Refer to the appropriate wiring diagram and inspect fuses and relays to confirm power is present at the motor. Check the aspirator motor ground connection to the climate control ECU for open circuits. If no wiring faults are found replace the interior air temperature sensor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B2373 | Parking Aid | LED #1 Circuit Short to Battery |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check parking aid status LED circuit for short to power or open circuit. Repair wiring harness using approved methods and materials, clear DTC and retest system to confirm correct operation. |
| B2401 | Radio Head Unit | Audio Tape Deck Mechanism Fault |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check radio head unit install a new module as required, refer to DTC Index |
| B2403 | Radio Head Unit | Audio CD/DJ Internal Fault |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check cd multi-changer module install a new module as required, refer to DTC Index |
| B2414 | Generic Electronic Module | Headlamp washer relay circuit short circuit to ground |
|
Check headlamp wash relay for condition, replace as required. Refer to appropriate SYSTEM WIRING DIAGRAMS. Check headlamp washer relay circuits for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2431 | Instrument Cluster | Transponder programming failed |
|
Suspect transponder keyfob PATS code transmit fault. Check and replace key fob as required. |
| B2434 | Supplemental Restraint System - Safety Belt System | Driver safety belt switch circuit fault |
|
For driver safety belt switch circuit tests, Refer to Pinpoint Test C . |
| B2435 | Supplemental Restraint System - Safety Belt System | Driver safety belt switch circuit fault |
|
For driver safety belt switch circuit tests, Refer to Pinpoint Test C . |
| B2438 | Supplemental Restraint System - Safety Belt System | Front passenger safety belt switch circuit fault |
|
For passenger safety belt switch circuit tests, Refer to Pinpoint Test D . |
| B2439 | Supplemental Restraint System - Safety Belt System | Front passenger safety belt switch circuit fault |
|
For passenger safety belt switch circuit tests, Refer to Pinpoint Test D . |
| B2449 | Heating and Ventilation - Auxiliary Heater | Auxiliary heater short circuit |
|
For auxiliary heater circuit tests. Refer to Pinpoint Test A , Pinpoint Test B and Pinpoint Test C . |
| B2450 | Heating and Ventilation - Auxiliary Heater | Auxiliary heater interrupted |
|
For auxiliary heater circuit tests. Refer to Pinpoint Test A , Pinpoint Test B and Pinpoint Test C . |
| B2462 | Climate Control System - General Information | Aux. Heater Flame Out Fault |
|
Check fuel supply lines to the auxiliary heater are free from damage, leaks or air ingress. Rectify any restrictions, leaks of air ingress. Clear DTC and test the system to verify the repair. |
| B2477 | Climate Control System - General Information | Module Configuration Failure |
|
Not used on X400 or set on delivered modules |
| B2477 | Instrument Cluster | Module configuration failure |
|
Enter vehicle configuration into instrument cluster using the manufacturer approved diagnostic system |
| B2477 | Exterior Lighting | Module configuration failure |
|
Configure control module using manufacturer approved diagnostic system |
| B2477 | Parking Aid | Module Configuration Failure |
|
Reconfigure. If this fails suspect faulty module, check and install as required. Refer to DTC Index . |
| B2477 | Gateway module | Module Configuration Failure |
|
The module can be configured using the new module procedure. Check and configure as required |
| B2477 | Radio Head Unit | Module Configuration Failure |
|
The module can be configured using the new module procedure. Check and configure as required |
| B2477 | Voice Activated Control Module | Module configuration failure |
|
The module can be configured using the new module procedure. Check and configure as required. |
| B2477 | Generic Electronic Module | Module configuration failure |
|
The ECU has not been configured or has been configured incorrectly. Use the manufacturer approved diagnostic equipment to configure the ECU correctly then retest to ensure correct operation. |
| B2477 | Supplemental Restraint System | RCM configuration fault |
|
Reconfigure the module using the Jaguar approved diagnostic system |
| B2494 | Generic Electronic Module | Anti theft horn output circuit short to battery |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS. Check anti theft horn output circuit for short to battery. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2496 | Generic Electronic Module | Anti theft horn output circuit short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS. Check anti theft horn output circuit for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2511 | Generic Electronic Module | Horn output relay circuit short to battery |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS. Check vehicle horn output relay circuit for short to battery. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2516 | Climate Control System - General Information | Blower Motor Failure |
NOTE:
This DTC is only relavent to the ATC version of the climate control system.
|
Validate the fault on the car. Check the blower motor is not stalled by a foreign object. Refer to the relevant circuit diagram and check the integrity of the wiring between the blower motor and the power distribution components. Check the fuses and relay which supply the motor. Check the motor supply lines between the Passenger Junction Box and motor for open or short circuits to ground. Check the motor ground lines to the ground point on the cross car beam for open circuits. Repair harness faults using approved repair kit. Replace blower motor if there are no harness faults |
| B2555 | Generic Electronic Module | Dome lamp output circuit short to battery |
|
Inspect Dome lamp for defects which may cause a short circuit to power. Replace or repair as required. If no faults are found in the dome lamp itself, check ECU output circuit to dome lamp for shorts to battery. Repair wiring harness using approved methods and materials. Clear DTC and retest system to confirm correct operation. |
| B2608 | Exterior Lighting | ECU output to left headlamp stepper motor short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check left headlamp stepper motor circuit for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2609 | Exterior Lighting | ECU output to left headlamp stepper motor circuit failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check left headlamp stepper motor circuit open circuit or short to power. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2610 | Exterior Lighting | ECU output driver to left headlamp stepper motor overtemperature |
|
Check headlamp unit for blocking of stepper motor movement, or continuous operation. Replace headlamp components as required. Clear DTC and retest system to ensure correct operation |
| B2611 | Exterior Lighting | ECU output to right headlamp stepper motor short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check right headlamp stepper motor circuit for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2612 | Exterior Lighting | ECU output to right headlamp stepper motor circuit failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check left headlamp stepper motor circuit open circuit or short to power. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2613 | Exterior Lighting | ECU output driver to right headlamp stepper motor overtemperature |
|
Check headlamp unit for blocking of stepper motor movement, or continuous operation. Replace headlamp components as required. Clear DTC and retest system to ensure correct operation |
| B2614 | Exterior Lighting | Front or rear axle vehicle level sensor supply short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check level sensor power supply circuit for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2615 | Exterior Lighting | Front or rear axle vehicle level sensor supply circuit failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check level sensor power supply circuit for short to power. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2616 | Exterior Lighting | Front axle vehicle level sensor signal circuit failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check level sensor signal circuit for open circuit, short to 5 volts, short to battery power. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2617 | Exterior Lighting | Front axle vehicle level sensor signal short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check front level sensor signal circuit for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2618 | Exterior Lighting | Front axle vehicle level sensor signal not plausible |
|
Front sensor signal out of range. Check lever position and adjustment of sensor. Replace sensor if signal cannot be brought into range. Refer to appropriate SYSTEM WIRING DIAGRAMS, check level sensor signal circuit for faults. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2619 | Exterior Lighting | Rear axle vehicle level sensor signal circuit failure |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check level sensor signal circuit for open circuit, short to 5 volts, short to battery power. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2620 | Exterior Lighting | Rear axle vehicle level sensor signal short to ground |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check rear level sensor signal circuit for short to ground. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2621 | Exterior Lighting | Rear axle vehicle level sensor signal not plausible |
|
Rear sensor signal out of range. Check lever position and adjustment of sensor. Replace sensor if signal cannot be brought into range. Refer to appropriate SYSTEM WIRING DIAGRAMS, check level sensor signal circuit for faults. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2622 | Exterior Lighting | Auto levelling ECU speed message invalid / not available |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check CAN circuits for faults. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2623 | Exterior Lighting | Auto levelling ECU low beam message invalid / not available |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check CAN circuits for faults. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2624 | Exterior Lighting | Auto levelling ECU speed signal not available |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check CAN circuits for faults. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2625 | Exterior Lighting | Auto levelling ECU low beam signal input open circuit |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, check ECU low beam input circuits for open circuits. Repair wiring harness using approved methods and materials. Clear DTC and retest system to ensure correct operation. |
| B2626 | Exterior Lighting | Auto levelling ECU not calibrated |
|
Calibrate and adjust the headlamp levelling ECU using the manufacturer approved diagnostic system. Clear DTC and retest system to confirm correct operation |
| B2627 | Instrument Cluster | Fuel sender circuit open #2 |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check the rear electronic module, fuel sender circuit for open circuit. |
| B2627 | Fuel Tank and Lines | Fuel level sensor 2 circuit fault |
|
For fuel level sensor circuit tests, Refer to Pinpoint Test A . |
| B2628 | Instrument Cluster | Fuel sender circuit short to ground #2 |
|
Carry out any pinpoint tests associated with this DTC using the manufacturer approved diagnostic system. Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check the rear electronic module, fuel sender circuit for short to ground. |
| B2628 | Fuel Tank and Lines | Fuel level sensor 2 circuit fault |
|
For fuel level sensor circuit tests, Refer to Pinpoint Test A . |
| B2646 | Navigation System | Antenna circuit open circuit #1 |
|
refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation systems antenna circuit for open circuit. To restore power the fault must be removed and the user must key off and on. |
| B2647 | Navigation System | Antenna circuit open circuit #2 |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation systems antenna circuit for open circuit. To restore power the fault must be removed and the user must key off and on. |
| B2648 | Navigation System | Antenna circuit open circuit #3 |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation systems antenna circuit for open circuit. To restore power the fault must be removed and the user must key off and on. |
| B2649 | Navigation System | Antenna circuit open circuit #4 |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation systems antenna circuit for open circuit. To restore power the fault must be removed and the user must key off and on. |
| B2650 | Navigation System | Antenna circuit short circuit #1 |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation systems antenna circuit for short to power or ground. To restore power the fault must be removed and the user must key off and on. |
| B2651 | Navigation System | Antenna circuit short circuit #2 |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation systems antenna circuit for short to power or ground. To restore power the fault must be removed and the user must key off and on. |
| B2652 | Navigation System | Antenna circuit short circuit #3 |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation systems antenna circuit for short to power or ground. To restore power the fault must be removed and the user must key off and on. |
| B2653 | Navigation System | Antenna circuit short circuit #4 |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation systems antenna circuit for short to power or ground. To restore power the fault must be removed and the user must key off and on. |
| B2655 | Navigation System | Switch and display module is defective |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation system display and switch module for failure. Install a new display module as required. Refer to DTC Index |
| B2656 | Navigation System | DVD (Digital Versatile Disk) error |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check navigation system module for faults. Install a new module as required. Refer to DTC Index |
| B2672 | Climate Control System - General Information | Discharge Air Temperature Sensor Circuit Open |
|
Refer to the relevant circuit diagram and check the integrity of the wiring between the discharge air temperature sensor and the Climate Control System ECU. Check for open circuits on the Discharge Sensor line and the sensor ground line between the sensor and the Climate Control ECU. If no wiring defects are found install a new Discharge Air Temperature Sensor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B2673 | Climate Control System - General Information | Discharge Air Temperature Sensor Circuit Short to Ground |
|
Refer to the relevant circuit diagram and check the integrity of the wiring between the discharge air temperature sensor and the Climate Control System ECU. Check for short circuits on the Discharge Sensor line between the sensor and the Climate Control ECU. If no wiring defects are found install a new Discharge Air Temperature Sensor. Clear the DTC and operate the system to check that the DTC does not reset. |
| B2691 | Supplemental Restraint System - Safety Belt System | Driver safety belt switch circuit fault |
|
For driver safety belt switch circuit tests, Refer to Pinpoint Test C . |
| B2692 | Supplemental Restraint System - Safety Belt System | Passenger safety belt switch circuit fault |
|
For passenger safety belt switch circuit tests, Refer to Pinpoint Test D . |
| B2879 | Instrument Cluster | Fuel tank jet pump fault |
|
Refer to appropriate SYSTEM WIRING DIAGRAMS, notes and check fuel level senders and fuel tank jet pump circuits for faults |
| B2879 | Fuel Tank and Lines | Failure to transfer fuel |
|
Carry out fuel transfer test, Refer to Pinpoint Test C . |
| B2888 | Radio Head Unit | Audio Head unit Media Fault |
|
Check radio head unit install a new module as required, refer to DTC Index |
| B2909 | Supplemental Restraint System - Safety Belt System | Front passenger belt tension sensor fault |
|
For belt tension sensor circuit tests, Refer to Pinpoint Test G . |
| B2909 | Supplemental Restraint System - Safety Belt System | Front passenger belt tension sensor fault |
|
For belt tension sensor circuit tests, Refer to Pinpoint Test G . |
| B2988 | Supplemental Restraint System | Knee bolster circuit open circuit |
|
For knee bolster circuit tests, Refer to Pinpoint Test K . |
| B2989 | Supplemental Restraint System | Knee bolster circuit short to battery |
|
For knee bolster circuit tests, Refer to Pinpoint Test K . |
| B2990 | Supplemental Restraint System | Knee bolster circuit short to ground |
|
For knee bolster circuit tests, Refer to Pinpoint Test K . |
| B2991 | Supplemental Restraint System | Knee bolster squib resistance low |
|
For knee bolster circuit tests, Refer to Pinpoint Test K . |