Test Description
WARNING: This page is about a different car, the 2007 Isuzu i-370, 2007 Isuzu i-290, 2007 GMC Canyon, and 2007 Chevrolet Colorado. However, it is still accessible from the selected car via links, so may be relevant.
The numbers below refer to the step numbers on the diagnostic table.
- 3:
A partial malfunction in the class 2 serial data circuit uses a different procedure from a total malfunction of the class 2 serial data circuit. The following modules communicate on the class 2 serial data circuit:
- The body control module (BCM)
- The electronic brake control module (EBCM)
- The inflatable restraint sensing and diagnostic module (SDM)
- The instrument panel cluster (IPC)
- The powertrain control module (PCM)
- The radio
- The rear seat entertainment (RSE) assembly
- The transfer case shift control module (TCSCM)
- The vehicle communication interface module (VCIM)
- 4:
The following DTCs may be retrieved with a history status, but are not the cause of the present condition.
- U1300
- U1301
- U1305
- 7: A state of health DTC with a history status may be present along with a U1000 or U1255 code having a current status. This indicates that the malfunction occurred when the ignition was ON.
- 8: Data link connector terminals 2 and 5 provide the connection to the class 2 serial data circuit and the signal ground circuit respectively.
- 18: If there are no current DTCs that begin with a "U", the communication malfunction has been repaired.
- 19: The communication malfunction may have prevented diagnosis of the customer complaint.
Scan Tool Does Not Communicate with Class 2 Device
| Step | Action | Yes | No |
|---|---|---|---|
| Schematic Reference: Data Communication Schematics Connector End View Reference: Master Electrical Component List |
|||
| 1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle |
| 2 | Does the scan tool power up? | Go to Step 3 | Go to Scan Tool Does Not Power Up |
| 3 |
|
Go to Step 4 | Go to Step 9 |
| 4 |
|
Go to Step 5 | Go to Step 8 |
| 5 | Are the history DTCs U1300, U1301 or U1305 retrieved from any module? | Go to Step 6 | Go to Step 7 |
| 6 |
IMPORTANT:
Turn ON the ignition, with the engine OFF, when testing for a short to voltage. Use the DMM MIN/MAX function to capture intermittent conditions. Test the class 2 serial data circuit for an intermittent short to ground or an intermittent short to voltage. Refer to the following:Did you find and correct the condition? |
Go to Step 18 | Go to Step 7 |
| 7 | Are U1000 or U1255 the only DTCs displayed in the previously specified range? | Go to DTC U1000 and U1255 | Go to DTC U1001-U1254 |
| 8 | Diagnose the non-communicating module by using the DTC U1001-U1254 procedure for the module which is not communicating. Refer to DTC U1001-U1254 . Did you complete the action? |
Go to Diagnostic System Check - Vehicle | - |
| 9 |
|
Go to Diagnostic System Check - Vehicle | Go to Step 10 |
| 10 | Test the DLC ground circuit at terminal 5 for an open. Refer to Circuit Testing
and Wiring Repairs
. Did you find and correct the condition? |
Go to Diagnostic System Check - Vehicle | Go to Step 11 |
| 11 | Repeat the following steps on the class 2 serial data circuits until the communication with body control module (BCM) is established or all modules listed below were disconnected.
Does the scan tool communicate with the BCM? |
Go to Step 12 | Go to Step 15 |
| 12 |
IMPORTANT:
Perform this step only if the suspected module is IPC or Radio.
|
Go to Step 18 | Go to Step 13 |
| 13 | Inspect for poor connections at the class 2 serial data circuit of the last disconnected module. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
. Did you find and correct the condition? |
Go to Step 18 | Go to Step 14 |
| 14 | Replace the last disconnected module. Refer to Control Module References
for replacement, setup, and programming. Did you complete the replacement? |
Go to Step 18 | - |
| 15 |
|
Go to Step 18 | Go to Step 16 |
| 16 | Inspect for poor connections at the class 2 serial data circuit of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections
and Connector Repairs
. Did you find and correct the condition? |
Go to Step 18 | Go to Step 17 |
| 17 | Replace the BCM. Refer to Control Module References
for replacement, setup, and programming. Did you complete the replacement? |
Go to Step 18 | - |
| 18 |
|
Go to Diagnostic Trouble Code (DTC) List - Vehicle | Go to Step 19 |
| 19 | Did you record any DTCs which do not begin with a "U"? | Go to Diagnostic Trouble Code (DTC) List - Vehicle | Go to Step 20 |
| 20 | Use the scan tool in order to clear the DTCs. Did you complete the action? |
System OK | - |