LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2012 >> G25 Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 6 (EV Control System) >> DTC/Circuit Diagnosis >> SSOFF Relay >> Diagnosis Procedure

Diagnosis Procedure

WARNING: This page is about a different car, the 2011 Nissan Leaf. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FUSE
    1. Turn power switch OFF.
    2. Pull out #43 fuse.
    3. Check that the fuse is not fusing.

    Is the inspection result normal? 

    YES: Go to 2.

    NO: Replace the fuse after repairing the applicable circuit.

  2. CHECK BATTERY POWER SUPPLY-I
    1. Insert the fuse.
    2. Check the voltage between IPDM E/R harness connector and ground.
    VOLTAGE REFERENCE CHART

    + - Voltage
    IPDM E/R
    Connector Terminal
    E14 41 Ground Battery voltage

    Is the inspection result normal? 

    YES: Go to  6.

    NO: Go to 3.

  3. CHECK BATTERY POWER SUPPLY-II

    Check the voltage between IPDM E/R harness connector and ground.

    VOLTAGE REFERENCE CHART

    + - Voltage
    IPDM E/R
    Connector Terminal
    E9 2 Ground Battery voltage

    Is the inspection result normal? 

    YES: Go to  5.

    NO: Go to 4.

  4. CHECK FUSIBLE LINK
    1. Remove #D fusible link.
    2. Check that the fusible link is not fusing.

    Is the inspection result normal? 

    YES: Check power supply circuit for battery power supply.

    NO: Replace the fusible link after repairing the applicable circuit.

  5. CHECK SSOFF RELAY CONTROL CIRCUIT FOR SHORT TO GROUND
    1. Turn power switch OFF.
    2. Disconnect VCM harness connector.
    3. Check harness for short to ground between IPDM E/R harness connector and VCM harness connector.
    CONTINUITY REFERENCE CHART

    + - Continuity
    IPDM E/R VCM
    Connector Terminal Connector Terminal
    E14 41 E61 7 Existed

    Is the inspection result normal? 

    YES: Replace IPDM E/R. Refer to "REMOVAL AND INSTALLATION ".

    NO: Repair or replace error-detected parts.

  6. CHECK SSOFF RELAY CONTROL SIGNAL
    1. Turn power switch ON.
    2. Check the voltage between IPDM E/R harness connector and ground.
    VOLTAGE REFERENCE CHART

    + - Voltage (Approx.)
    IPDM E/R
    Connector Terminal
    E14 41 Ground 0 V

    Is the inspection result normal? 

    YES: Go to  10.

    NO: Go to 7.

  7. CHECK SS OFF RELAY CONTROL SIGNAL CIRCUIT
    1. Turn power switch OFF.
    2. Disconnect VCM harness connector.
    3. Check the continuity between IPDM E/R harness connector and VCM harness connector.
      CONTINUITY REFERENCE CHART

      + - Continuity
      IPDM E/R VCM
      Connector Terminal Connector Terminal
      E14 41 E61 7 Existed
    4. Also check harness for short to ground and short to power.

    Is the inspection result normal? 

    YES: Go to 8.

    NO: Repair or replace error-detected parts.

  8. CHECK VCM GROUND CIRCUIT

    Check the continuity between VCM harness connector and ground.

    CONTINUITY REFERENCE CHART

    + - Continuity
    IPDM E/R
    Connector Terminal
    E61 4 Ground Existed
    8
    E63 111
    112

    Is the inspection result normal? 

    YES: Go to 9.

    NO: Repair or replace error-detected parts.

  9. CHECK INTERMITTENT INCIDENT

    Check intermittent incident. Refer to "INTERMITTENT INCIDENT ".

    Is the inspection result normal? 

    YES: Replace VCM. Refer to "REMOVAL AND INSTALLATION ".

    NO: Repair or replace error-detected parts.

  10. CHECK SSOFF RELAY OUTPUT VOLTAGE

    Check the voltage between IPDM E/R harness connector and ground.

    VOLTAGE REFERENCE CHART

    + - Voltage
    IPDM E/R
    Connector Terminal
    E14 36 Ground 12V battery voltage

    Is the inspection result normal? 

    YES: INSPECTION END

    NO: Replace IPDM E/R. Refer to "REMOVAL AND INSTALLATION ".