LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 2012 >> G25 Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 6 (EV Control System) >> DTC/Circuit Diagnosis >> M/C Relay >> Diagnosis Procedure

Diagnosis Procedure

WARNING: This page is about a different car, the 2011 Nissan Leaf. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK M/C RELAY CONTROL CIRCUIT
    1. Turn power switch OFF.
    2. Remove M/C relay.
    3. Check the voltage between M/C relay harness connector terminals.
      VOLTAGE REFERENCE CHART

      M/C relay Voltage
      Connector + -
      Terminal
      E65 2 1 0 V
    4. Turn power switch ON.
    5. Check the voltage between M/C relay harness connector terminals.
    VOLTAGE REFERENCE CHART

    M/C relay Voltage
    Connector + -
    Terminal
    E65 2 1 12V battery voltage

    Is the inspection result normal? 

    YES: Go to  9.

    NO: Go to 2.

  2. CHECK BATTERY POWER SUPPLY-I

    Check the voltage between M/C relay harness connector and ground.

    VOLTAGE REFERENCE CHART

    + - Voltage
    M/C relay
    Connector Terminal
    E65 2 Ground 12V battery voltage

    Is the inspection result normal? 

    YES: Go to  6.

    NO: Go to 3.

  3. CHECK FUSIBLE LINK
    1. Remove #G fusible link.
    2. Check that the fusible link is not fusing.

    Is the inspection result normal? 

    YES: Go to 4.

    NO: Replace the fusible link after repairing the applicable circuit.

  4. CHECK BATTERY POWER SUPPLY-II

    Check the voltage between fusible link harness connector and ground.

    VOLTAGE REFERENCE CHART

    + - Voltage
    #G fusible link terminal Ground 12V battery voltage

    Is the inspection result normal? 

    YES: Go to 5.

    NO: Check power supply circuit for battery power supply.

  5. CHECK BATTERY POWER SUPPLY CIRCUIT-I
    1. Check the continuity between M/C relay harness connector and fusible link harness connector.
      CONTINUITY REFERENCE CHART

      + - Continuity
      M/C relay
      Connector Terminal
      #G fusible link terminal E65 2 Existed
    2. Also check harness for short to ground and short to power.

    Is the inspection result normal? 

    YES: Check intermittent incident. Refer to "INTERMITTENT INCIDENT ".

    NO: Repair or replace error-detected parts.

  6. CHECK M/C RELAY CONTROL SIGNAL CIRCUIT
    1. Turn power switch OFF.
    2. Disconnect VCM harness connector.
    3. Check the continuity between M/C relay harness connector and VCM harness connector.
      CONTINUITY REFERENCE CHART

      + - Continuity
      M/C relay VCM
      Connector Terminal Connector Terminal
      E65 1 E62 78 Existed
    4. Also check harness for short to ground and short to power.

    Is the inspection result normal? 

    YES: Go to 7.

    NO: Repair or replace error-detected parts.

  7. CHECK VCM GROUND CIRCUIT

    Check the continuity between VCM harness connector and ground.

    CONTINUITY REFERENCE CHART

    + - Continuity
    VCM
    Connector Terminal
    E61 4 Ground Existed
    8
    E63 111
    112

    Is the inspection result normal? 

    YES: Go to 8.

    NO: Repair or replace error-detected parts.

  8. CHECK INTERMITTENT INCIDENT

    Check intermittent incident. Refer to "INTERMITTENT INCIDENT ".

    Is the inspection result normal? 

    YES: Replace VCM. Refer to "REMOVAL AND INSTALLATION ".

    NO: Repair or replace error-detected parts.

  9. CHECK BATTERY POWER SUPPLY-III

    Check the voltage between M/C relay harness connector and ground.

    VOLTAGE REFERENCE CHART

    + - Voltage
    M/C relay
    Connector Terminal
    E65 3 Ground 12V battery voltage

    Is the inspection result normal? 

    YES: Go to  11.

    NO: Go to 10.

  10. CHECK BATTERY POWER SUPPLY CIRCUIT-II
    1. Check the continuity between M/C relay harness connector and fusible link harness connector.
      CONTINUITY REFERENCE CHART

      + - Continuity
      M/C relay
      Connector Terminal
      #G fusible link terminal E65 3 Existed
    2. Also check harness for short to ground and short to power.

    Is the inspection result normal? 

    YES: Check intermittent incident. Refer to "INTERMITTENT INCIDENT ".

    NO: Repair or replace error-detected parts.

  11. CHECK M/C RELAY

    Refer to "COMPONENT INSPECTION (M/C RELAY) ".

    Is the inspection result normal? 

    YES: INSPECTION END

    NO: Replace M/C relay.