LEMON Manuals: Even more car manuals for everyone
Home >> Infiniti >> 1996 >> I30 Base, Automatic, RE4F04A >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Tests W/Codes 3.0L >> Circuit Tests >> DTC P1900 - Radiator Cooling Fan Control

DTC P1900 - Radiator Cooling Fan Control

  1. Low Speed Operation Turn ignition off. Disconnect radiator cooling fan relay No. 2 and 3. See Fig 3. Start engine and allow to idle. Set temperature lever to full cold position. Turn A/C and blower switch on. Allow engine to idle for several minutes. If fan does not operate at low speed, go to next step. If fan operates at low speed, go to HIGH SPEED OPERATION.
  2. Check Power Supply Turn ignition off. Disconnect radiator cooling fan relay No. 1. Turn ignition on. Measure voltage between ground and relay terminals No. 1 and 3. See Fig 5. If battery voltage is present, go to step 4). If battery voltage is not present, go to next step.
  3. Check 10-amp fuse, 30-amp fusible link and harness connectors. Ensure continuity exists between fan relay No. 1 and battery. Repair or replace harness and/or connector as necessary.
  4. Check Ground Circuit Turn ignition off. Disconnect both cooling fan motor harness connectors. See Fig 4. Check for continuity between fan motor connector terminal "1" and relay terminal No. 5. See Fig 6. Check for continuity between ground and fan motor connector terminal "4". See Fig 3. If continuity is not present, repair harness or connectors. If continuity is present, go to next step.
  5. Check Output Signal Circuit Disconnect ECM harness connector. Check for continuity between relay terminal No. "2" and ECM harness connector terminal No. 14. See Fig 6. If continuity is not present, repair harness or connector. If continuity is present, go to step 8).
  6. High Speed Operation Turn ignition off. Reconnect radiator cooling fan relay No. "2" and "3". Disconnect radiator cooling fan relay No. "1". Turn A/C switch and blower switch off. Disconnect Engine Coolant Temperature (ECT) sensor connector. Connect a 150-ohm resistor between ECT terminals. Start engine and allow to idle for several minutes. If fan does not operate at high speed, go to next step. If fan operates at high speed, testing is complete. If symptom is still present, check radiator or thermostat for fault.
  7. Check Circuit Continuity Turn ignition off. Disconnect cooling fan relays No. "2" and "3". Disconnect triple-pressure switch harness connector. Check for continuity between relay terminal No. "2" and triple switch terminal No. 3. See Fig 7. Check for continuity between ground and triple switch terminal No. 3. If continuity is not present, repair harness or connector. If continuity is present, check radiator or thermostat for fault. If no faults are found, replace triple switch.
  8. Check Cooling Fan Relay No. 1 Connect relay terminal No. "1" to ground. See Fig 9. Using jumper wire, apply battery voltage to terminal No. "2". Check continuity as follows:
    • Verify continuity is present between relay terminals No. "3" and "5".

Remove battery voltage from relay. Check continuity as follows:

If continuity is not as specified, replace cooling fan relay. If continuity is as specified, go to next step.

9) Check Cooling Fan Relay No. 2 & 3 Connect relay terminal No. "1" to ground. See Fig 10. Using jumper wire, apply battery voltage to terminal No. "2". Check continuity as follows:

Remove battery voltage from relay. Check continuity as follows:

If continuity is not as specified, replace cooling fan relay. If continuity is as specified, go to next step.

10) Check Cooling Fan Motor With cooling fan motor disconnected, apply fused battery power to terminal "1". When ground is supplied to terminal "4", cooling fan motor should operate at low speed. Apply fused battery power to terminal "1" and "2". When ground is supplied to terminal "3" and "4", cooling fan motor should operate at high speed. If motor operates as specified, testing is complete. If cooling fan motor does not operate, go to next step.

11) Disconnect ECM wiring harness connector. Check connector pins for damage or corrosion. Check all circuit connectors for clean, tight fit and service if necessary. Loosen and retighten engine ground screws. See Figure.

Fig 1: Locating Cooling Fan Relays (I30)
G96G10633Courtesy of NISSAN MOTOR CO., U.S.A.
Fig 2: Locating Cooling Fan Motor Harness Connectors (I30)
G96H10634Courtesy of NISSAN MOTOR CO., U.S.A.
Fig 3: DTC P1900, Checking Power Supply Circuit (I30)
G96J10636Courtesy of NISSAN MOTOR CO., U.S.A.
Fig 4: DTC P1900, Checking Ground Circuit (I30)
G96A10637Courtesy of NISSAN MOTOR CO., U.S.A.
Fig 5: DTC P1900, Checking Ground Circuit (I30)
G96B10638Courtesy of NISSAN MOTOR CO., U.S.A.
Fig 6: DTC P1900, Checking Output Signal Circuit (I30)
G96C10639Courtesy of NISSAN MOTOR CO., U.S.A.
Fig 7: DTC P1900, Checking Circuit Continuity (I30)
G96I10635Courtesy of NISSAN MOTOR CO., U.S.A.
Fig 8: DTC P1900, Identifying Cooling Fan Relay No. 1 Terminals (I30)
G96F10640Courtesy of NISSAN MOTOR CO., U.S.A.
Fig 9: DTC P1900, Identifying Cooling Fan Relay No. 2 & No. 3 Terminals (I30)
G96G10641Courtesy of NISSAN MOTOR CO., U.S.A.
Fig 10: DTC P1900, Testing Cooling Fan Motor (I30)
G96H10642Courtesy of NISSAN MOTOR CO., U.S.A.