LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2019 >> Elantra SEL >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 54 (Timing System - 1.4L) >> Timing Chain >> Repair Procedures >> Installation

Repair Procedures: Installation

WARNING: This page is about a different variant/trim than selected.
  1. Set the key of crankshaft about 3.7° with horizontal center line. As a result of this, the piston of No. 1 cylinder is placed at the top dead center on compression stroke.
    G12976548Courtesy of HYUNDAI MOTOR AMERICA
  2. Install the crankshaft sprocket (A).
    G12976549Courtesy of HYUNDAI MOTOR AMERICA
  3. Align the mark of cam shaft sprocket (CVVT) on the top surface of cylinder head. As a result of this, the piston of No. 1 cylinder is placed at the top dead center on compression stroke.
    G12976550Courtesy of HYUNDAI MOTOR AMERICA
  4. Install the timing chain (A).
    NOTE:
    • Install the timing chain with no slack and recommend the below procedure.
    • Crankshaft sprocket → Oil pump sprocket → Intake camshaft sprocket (CVVT) → Exhaust camshaft sprocket (CVVT).
    • The timing mark of each sprocket should be matched with timing mark (color link) of timing chain at during installation.
    G12976551Courtesy of HYUNDAI MOTOR AMERICA
    G12976552Courtesy of HYUNDAI MOTOR AMERICA
    G12976553Courtesy of HYUNDAI MOTOR AMERICA
  5. Install the timing chain crank guide (A).

    Tightening torque  :

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G12976554Courtesy of HYUNDAI MOTOR AMERICA
  6. Install the timing chain cam guide (A).

    Tightening torque  :

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G12976555Courtesy of HYUNDAI MOTOR AMERICA
  7. Install the timing chain guide (A).

    Tightening torque  :

    18.6 - 21.6 N.m (1.9 - 2.2 kgf.m, 13.7 - 15.9 lb-ft)

    G12976556Courtesy of HYUNDAI MOTOR AMERICA
  8. Install the timing chain tensioner arm (A).

    Tightening torque  :

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G12976557Courtesy of HYUNDAI MOTOR AMERICA
  9. Install the timing chain tensioner (A) and then remove the stopper pin.

    Tightening torque  :

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb-ft)

    G12976558Courtesy of HYUNDAI MOTOR AMERICA
  10. After rotating the crankshaft 2 revolutions in regular direction (clockwise viewed from front), confirm the timing
    NOTE:
    • Always turn the crankshaft clockwise.
    • Turning the crankshaft counter clockwise before building up oil pressure in the hydraulic timing chain tensioner may result in the chain disengaging from the sprocket teeth.
  11. Install the other parts in the reverse order of removal.
    NOTE:
    • Refill engine with engine oil.
    • Clean battery posts and cable terminals and assemble.
    • Inspect for fuel leakage.
      • After assembling the fuel line, turn on the ignition switch (do not operate the starter) so that the fuel pump runs for approximately two seconds and fuel line pressurizes.
      • Repeat this operation two or three times, then check for fuel leakage at any point in the fuel line.