LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2018 >> Tucson SEL Plus, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 11 (Automatic Transaxle System - 2.4L) >> Automatic Transaxle >> Repair Procedures >> Removal

Repair Procedures: Removal

WARNING: This page is about a different variant/trim than selected.
  1. Remove the engine cover.

    (Refer to Engine Mechanical System - "ENGINE COVER ")

  2. Remove the air cleaner assembly and air duct.

    (Refer to Engine Mechanical System - "AIR CLEANER ")

  3. Remove the battery and battery tray.

    (Refer to Engine Electrical System - "BATTERY ")

  4. Disconnect the solenoid valve connector (A) and inhibitor switch connector (B).
    G12612926Courtesy of HYUNDAI MOTOR AMERICA
  5. Remove the fixing clips (A), (B) of wiring.
    G12612927Courtesy of HYUNDAI MOTOR AMERICA
  6. Remove the fixing clips (A) of wiring.
    G12612928Courtesy of HYUNDAI MOTOR AMERICA
  7. Remove the control cable (B) after removing the nut (C) and the bolt (A).

    Tightening torque: 

    (A) 14.7 - 21.6 N.m (1.5 - 2.2 kgf.m, 10.9 - 15.9 lb-ft)

    (C) 9.8 - 14.7 N.m (1.0 - 1.4 kgf.m, 7.2 - 10.8 lb-ft)

    G12612929Courtesy of HYUNDAI MOTOR AMERICA
  8. Remove the ground line after removing the bolt (A).
    G12612930Courtesy of HYUNDAI MOTOR AMERICA
  9. Disconnect the ATF cooler hose (A) after disconnecting the clamp.
    G12612931Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • Carefully install the clamp not to damage the hose
    • Install the clamp in a correct direction not to be interfered with other parts
    • After the installation, start the engine and then check if there are any leakages from the hose
  10. Remove the fender side cover (A) after loosening the mounting clips.
    G12612932Courtesy of HYUNDAI MOTOR AMERICA
  11. Assemble the engine support fixture (beam No.: 09200-38001 or 09200-3N000, supporter No.: 09200-2S000, adapter No.:09200-2W000).

    (Refer to Engine support fixture assembly drawing - " SPECIAL SERVICE TOOLS ")

  12. Using the engine support fixture (A), hold the engine and transaxle assembly safely.
    G12612933Courtesy of HYUNDAI MOTOR AMERICA
  13. Remove the automatic transaxle upper mounting bolt (A-2ea) and the starter mounting bolt (B-2ea).

    Tightening torque: 

    (A) 42.2 - 54.0 N.m (4.3 - 5.5 kgf.m, 31.1 - 39.8 lb-ft)

    (B) 49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47.0 lb-ft)

    G12612934Courtesy of HYUNDAI MOTOR AMERICA
  14. Remove the automatic transaxle mounting bracket cover (A).
    G12612935Courtesy of HYUNDAI MOTOR AMERICA
  15. Remove the automatic transaxle support bracket mounting bolts (A).

    Tightening torque: 

    88.3 - 107.9 N.m (9.0 - 11.0 kgf.m, 65.1 - 79.8 lb-ft)

    G12612936Courtesy of HYUNDAI MOTOR AMERICA
  16. Remove the automatic transaxle support bracket (A).

    Tightening torque: 

    58.8 - 78.5 N.m (6.0 - 8.0 kgf.m, 43.4 - 57.9 lb-ft)

    G12612937Courtesy of HYUNDAI MOTOR AMERICA
  17. Lift the vehicle with a jack.
  18. Remove the under cover.

    (Refer to Engine Mechanical System - "ENGINE ROOM UNDER COVER ")

  19. Remove the drive shaft assembly.

    (Refer to Driveshaft and Axle - "FRONT DRIVESHAFT ")

  20. Remove the dust cover (A).
    G12612938Courtesy of HYUNDAI MOTOR AMERICA
  21. Remove the torque converter mounting bolts (A) with rotating the crankshaft.

    Tightening torque: 

    45.1 - 52.0 N.m (4.6 - 5.3 kgf.m, 33.3 - 38.3 lb-ft)

    G12612939Courtesy of HYUNDAI MOTOR AMERICA
  22. Remove the roll rod bracket (C) after removing the bolt (A) and (B).

    Tightening torque: 

    Bolt (A): 49.0 - 63.7 N.m (5.0 - 6.5 kgf.m, 36.2 - 47.0 lb-ft)

    Bolt (B): 107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)

  23. Remove the roll road support bracket (D).

    Tightening torque: 

    49.0 - 68.6 N.m (5.0 - 7.0 kgf.m, 36.2 - 50.6 lb-ft)

    G12612940Courtesy of HYUNDAI MOTOR AMERICA
  24. Remove the automatic transaxle with a jack after removing the mounting bolts (A, B).

    Tightening torque: 

    1. 42.2 - 48.1 N.m (4.3 - 4.9 kgf.m, 31.1 - 35.4 lb-ft)
    2. 42.2 - 54.0 N.m (4.3 - 5.5 kgf.m, 31.1 - 39.8 lb-ft)
    G12612941Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • Be careful not to damage other system or parts near by when removing the transaxle assembly.