LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2014 >> Tucson SE, 4WD >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Engine And Transmission Assembly - 2.4L >> Engine And Transmission Assembly >> Repair Procedures >> Removal

Repair Procedures: Removal

CAUTION:
  • Use fender covers to avoid damaging painted surfaces.
  • To avoid damage, unplug the wiring connectors carefully while holding the connector portion.
NOTE:
  • Mark all wiring and hoses to avoid misconnection.
  • For release the fuel system pressure before remove the engine assembly, start the engine without fuel pump relay. And then turn off the ignition switch after engine stops.
  1. Disconnect the battery negative terminal.
  2. Remove the plastic engine cover.
  3. Remove the air cleaner assembly.

    (Refer to AIR CLEANER )

  4. Disconnect the battery positive terminal and then remove the battery.

    (Refer to BATTERY )

  5. Remove the battery tray.

    (Refer to BATTERY )

  6. Remove the under cover.
  7. Loosen the drain plug and drain the coolant. Remove the radiator cap to speed draining.

    (Refer to REPAIR PROCEDURES )

  8. Remove the radiator upper hose and lower hose.

    (Refer to REMOVAL AND INSTALLATION )

  9. Recover the refrigerant and then remove the high pressure pipe and low pressure pipe.

    (Refer to COMPRESSOR )

  10. Disconnect the (+) cable (A) from the fuse box and the front connector (B).
    Fig 1: Identifying Front Connector & Cable
    G09801961Courtesy of HYUNDAI MOTOR AMERICA
  11. Disconnect the wiring connectors, harness clamps from the engine.
    1. Exhaust OCV connector (A)
    2. Intake OCV connector (B)
    3. Injector connectors (C)
    4. Intake CMPS connector (D)
    5. Extension connector (E)
      Fig 2: Identifying Intake CMPS Connector, Injector Connectors And OCV Connector
      G09801962Courtesy of HYUNDAI MOTOR AMERICA
    6. Exhaust OCV connector (A)
      Fig 3: Identifying OCV Connector
      G09801963Courtesy of HYUNDAI MOTOR AMERICA
    7. Variable intake system (VIS) connector (A)
    8. Oil pressure switch (OPS) connector (B)
    9. Injector extension connector (C)
    10. Knock sensor connector (D)
    11. A/C compressor switch connector (E)
    12. Alternator connector (F)
      Fig 4: Identifying Injector Extension, Oil Pressure Switch And Variable Intake System Connectors
      G09801964Courtesy of HYUNDAI MOTOR AMERICA
    13. ETC connector (A)
    14. MAP & IATS connector (B)
      Fig 5: Identifying ETC, MAP And IATS Connectors
      G09801965Courtesy of HYUNDAI MOTOR AMERICA
    15. PCSV connector (A)
    16. ECT sensor connector (B)
    17. Condenser connector (C)
    18. CKP sensor connector (D)
    19. Front oxygen sensor connector (E) and rear oxygen sensor connector (F)
      Fig 6: Identifying CKP Sensor, Condenser, ECT Sensor And PCSV Connectors
      G09801966Courtesy of HYUNDAI MOTOR AMERICA
  12. Remove the transaxle wire harness connectors and control cable from the transaxle.
  13. Disconnect the fuel hose (A) and PCSV (Purge control solenoid valve) hose (B).
    Fig 7: Identifying Purge Control Solenoid Valve & Fuel Hoses
    G09801967Courtesy of HYUNDAI MOTOR AMERICA
  14. Disconnect the heater hoses (A) and brake vacuum hose (B).
    Fig 8: Identifying Heater And Brake Vacuum Hose
    G09801968Courtesy of HYUNDAI MOTOR AMERICA
  15. Remove the front muffler.

    (Refer to REPAIR PROCEDURES )

  16. Remove the center muffler and the propeller shaft (4WD only).

    (Refer to PROPELLER SHAFT )

  17. Remove the roll road bracket (A).

    Tightening torque 

    Bolt (C):

    107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)

    Bolt (B):

    49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

    Fig 9: Identifying Roll Road Bracket And Bolts
    G09801969Courtesy of HYUNDAI MOTOR AMERICA
  18. Remove the roll road support bracket (A).

    Tightening torque: 

    44.1 ~ 58.8 N.m (4.5 ~ 6.0 kgf.m, 32.5 ~ 43.4 lb-ft)

    Fig 10: Identifying Roll Road Support Bracket
    G09801970Courtesy of HYUNDAI MOTOR AMERICA
  19. Support the sub frame with a jack, and then remove the sub frame assembly.

    (Refer to FRONT CROSSMEMBER )

  20. Disconnect the ground line (A), and then remove the engine mounting support bracket (B).

    Tightening torque: 

    Ground line bolt (A):

    10.8 ~ 13.7 N.m (1.1 ~ 1.4 kgf.m, 8.0 ~ 10.1 lb-ft)

    Nut (C):

    78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)

    Bolt (D) and nuts (E):

    78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)

    Fig 11: Identifying Ground Line Bolt, Engine Mounting Support Bracket Nut And Bolt
    G09801971Courtesy of HYUNDAI MOTOR AMERICA
  21. Disconnect the ground line (A).
    Fig 12: Identifying Ground Line
    G09801972Courtesy of HYUNDAI MOTOR AMERICA
  22. Remove the service cover (A).
    Fig 13: Identifying Service Cover
    G09801973Courtesy of HYUNDAI MOTOR AMERICA
  23. Remove the transaxle mounting bracket through bolts (A).

    Tightening torque: 

    88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

    Fig 14: Identifying Transaxle Mounting Bracket Through Bolts
    G09801974Courtesy of HYUNDAI MOTOR AMERICA
  24. Lower the engine and transaxle assembly using a floor jack and then remove the engine and transaxle assembly by lifting vehicle.
    Fig 15: Removing Engine And Transaxle Assembly
    G09801975Courtesy of HYUNDAI MOTOR AMERICA
    NOTE: When remove the engine and transaxle assembly, be careful not to damage any surrounding parts or body components.