LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2014 >> Tucson SE, 4WD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 7 (Timing System - 2.0L) >> Timing Chain >> Repair Procedures >> Installation

Repair Procedures: Installation

WARNING: This page is about a different variant/trim than selected.
  1. The TDC marks of the intake and exhaust CVVT sprockets are slightly turned from the TDC position as shown in illustration when the timing chain is removed.
    Fig 1: Identifying TDC Marks Of Intake And Exhaust CVVT Sprockets
    G09815291Courtesy of HYUNDAI MOTOR AMERICA
  2. Turn the crankshaft clockwise (about 1~2 pitches) from the TDC position (the dowel pin (A) of crankshaft is about 3° with the engine vertical line) as rotation of the intake CVVT sprocket from the TDC position.
    Fig 2: Turning Crankshaft Clockwise From TDC Position
    G09815292Courtesy of HYUNDAI MOTOR AMERICA
  3. Install the timing chain guide (A).

    Tightening torque: 

    18.6 ~ 22.6 N.m (1.9 ~ 2.3 kgf.m, 13.7 ~ 16.6 lb-ft)

    Fig 3: Identifying Timing Chain Guide
    G09815293Courtesy of HYUNDAI MOTOR AMERICA
  4. Install the timing chain tensioner arm (A).

    Tightening torque: 

    18.6 ~ 22.6 N.m (1.9 ~ 2.3 kgf.m, 13.7 ~ 16.6 lb-ft)

    Fig 4: Identifying Timing Chain Tensioner Arm
    G09815294Courtesy of HYUNDAI MOTOR AMERICA
  5. Install the timing chain.

    Crankshaft sprocket (A) → Timing chain guide (B) → Intake CVVT sprocket (C) → Exhaust CVVT sprocket (D)

    1. Install the timing chain with no slack between the crankshaft sprocket and the intake CVVT sprocket.
      Fig 5: Identifying Timing Chain
      G09815295Courtesy of HYUNDAI MOTOR AMERICA
      NOTE: The timing marks of each sprocket should be matched with timing marks (color link) of timing chain when installing the timing chain.
    2. Install the timing chain on the exhaust CVVT sprocket with no slack while turning the CVVT assembly clockwise.
      Fig 6: Turning CVVT Assembly Clockwise
      G09815296Courtesy of HYUNDAI MOTOR AMERICA
      NOTE:
      • The timing mark of the exhaust CVVT sprocket should be matched with timing mark (color link) of timing chain when installing the timing chain.
      • Press down the timing chain links on the exhaust CVVT sprocket to prevent the sprocket from spinning.
  6. Install the timing chain auto tensioner (A) and remove the stopper pin (B).

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 7: Identifying Timing Chain Auto Tensioner And Stopper Pin
    G09815297Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • When reinstalling the tensioner, check the ratchet function of the tensioner after removing the fixing pin by retracting the tensioner arm (A) maximally as shown in illustration.
    • When maximally retracted, there should be no interference between the tensioner arm (A) and tensioner housing (B).
      Fig 8: Identifying Tensioner Arm & Tensioner Housing
      G09815298Courtesy of HYUNDAI MOTOR AMERICA
  7. After rotating crankshaft 2 revolutions in regular direction (clockwise viewed from front), confirm that the TDC marks on the intake and exhaust CVVT sprockets are aligned with the top surface of cylinder head.
    Fig 9: Identifying TDC Marks On Intake And Exhaust CVVT Sprockets
    G09815299Courtesy of HYUNDAI MOTOR AMERICA
  8. Install the timing chain cover.
    1. Using a gasket scraper, remove all the old packing material from the gasket surfaces.
    2. The sealant locations on the chain cover and the counter parts (cam carrier, cylinder head, cylinder block, and lower crankcase) must be free of harmful foreign materials, oil, dust and moisture. Spraying cleaner on the surface and wiping with a clean duster.
    3. Before assembling the timing chain cover, liquid sealant should be applied on the gap between cam carrier, cylinder head and cylinder block.

      Bead width:  3.0 ~ 5.0 mm (0.11 ~ 0.20 in.)

      Sealant:  Threebond 1217H or equivalent

      Fig 10: Identifying Cylinder Head And Block Liquid Sealant Applying Area
      G09815300Courtesy of HYUNDAI MOTOR AMERICA
    4. After applying liquid sealant on the timing chain cover, assemble the cover within 5 minutes after sealant was applied. Continuous bead of sealant should be applied to prevent any path from oil leakage.

      Bead width 

      Whole section: 2.5 ~ 3.5 mm (0.10 ~ 0.14 in.)

      Section A: 4.5 ~ 5.5 mm (0.18 ~ 0.22 in.)

      Section B: 8.0 ~ 9.0 mm (0.32 ~ 0.35 in.)

      Sealant:  Threebond 1217H or equivalent

      Fig 11: Applying Liquid Sealant On Timing Chain Cover
      G09815301Courtesy of HYUNDAI MOTOR AMERICA
    5. Install the timing chain cover. The dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in exact position.

      Tightening torque 

      Bolts (A, B):

      18.6 ~ 23.5 N.m (1.9 ~ 2.4 kgf.m, 13.7 ~ 17.4 lb-ft)

      Bolt (C):

      19.6 ~ 23.5 N.m (2.0 ~ 2.4 kgf.m, 14.5 ~ 17.4 lb-ft)

      Bolts (D, E):

      39.2 ~ 49.0 N.m (4.0 ~ 5.0 kgf.m, 28.9 ~ 36.2 lb-ft)

      Bolt (F):

      9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

      Fig 12: Timing Chain Cover Bolts Tightening Sequence
      G09815302Courtesy of HYUNDAI MOTOR AMERICA
      CAUTION: Do not reuse the seal bolts (C, F).
      CAUTION: The engine running or pressure test should not be performed within 30 minutes after the timing chain cover was assembled.
  9. Install the water pump assembly (A) with the gasket (B).

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 13: Identifying Water Pump Assembly And Gasket
    G09815303Courtesy of HYUNDAI MOTOR AMERICA
  10. Replace the front oil seal if necessary.
    1. Apply engine oil on the edge of new oil seal.
      CAUTION: Remove any debris from the lip portion of the oil seal.
    2. Install the front oil seal using SST (09231-2E000).
      Fig 14: Installing Front Oil Seal Using SST (09231-2E000)
      G09815304Courtesy of HYUNDAI MOTOR AMERICA
  11. Install the crankshaft damper pulley (A).

    Tightening torque: 

    196.1 ~ 205.9 N.m (20.0 ~ 21.0 kgf.m, 144.7 ~ 151.9 lb-ft)

    Fig 15: Identifying Crankshaft Damper Pulley
    G09815305Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION: Do not press the pulley or apply the excessive force to prevent the rubber part from being deformed.
    NOTE: There are two methods to hold the ring gear when installing the crankshaft damper pulley.
    • Install the SST (09231-2B100) to hold the ring gear after removing the starter.
      Fig 16: Holding Ring Gear Using Tool
      G09815306Courtesy of HYUNDAI MOTOR AMERICA
    • Install the SST (09231-3D100) to hold the ring gear after removing the service cover.
    1. Remove the air guard (A).
      Fig 17: Identifying Air Guard
      G09815307Courtesy of HYUNDAI MOTOR AMERICA
    2. Remove the two transaxle mounting bolts (A) and the service cover (B) on the bottom of the lower crankcase.
      Fig 18: Identifying Transaxle Mounting Bolts And Service Cover
      G09815308Courtesy of HYUNDAI MOTOR AMERICA
    3. Adjust the length of the holder (A) so that the grooves of the holder puts into the ring gears (B) at the closest position.
    4. Adjust the angle and length of the links (C) so that the two transaxle mounting bolts can be fastened into the original mounted holes.
      Fig 19: Identifying Length Of Holder, Links And Ring Gears
      G09815309Courtesy of HYUNDAI MOTOR AMERICA
    5. Install the SST using the two transaxle mounting bolts. Tighten the bolts and nuts of the holder and links securely.
      Fig 20: Tightening Bolts And Nuts Of Holder
      G09815310Courtesy of HYUNDAI MOTOR AMERICA
  12. Install the water pump pulley (A).

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 21: Identifying Water Pump Pulley
    G09815311Courtesy of HYUNDAI MOTOR AMERICA
  13. Install the A/C compressor (A). (Refer to COMPRESSOR )
    Fig 22: Identifying A/C Compressor
    G09815312Courtesy of HYUNDAI MOTOR AMERICA
  14. Install the front engine hanger (A).

    Tightening torque: 

    34.3 ~ 39.2 N.m (3.5 ~ 4.0 kgf.m, 25.3 ~ 28.9 lb-ft)

    Fig 23: Identifying Front Engine Hanger
    G09815313Courtesy of HYUNDAI MOTOR AMERICA
  15. Install the drive belt.
    1. Preassemble the alternator (A) temporarily.
      Fig 24: Identifying Alternator Bolts
      G09815314Courtesy of HYUNDAI MOTOR AMERICA
    2. Install the drive belt (B).
    3. Adjust the tension by turning the tension adjusting bolt (A) clockwise. (Refer to ALTERNATOR )

      Belt tension 

      New belt:

      637.4 ~ 735.5 N (65 ~ 75 kgf, 143.3 ~ 165.3 lbf)

      Used belt:

      441.3 ~ 539.4 N (45 ~ 55 kgf, 99.2 ~ 121.3 lbf)

      Fig 25: Engine Drive Belt Routing
      G09815315Courtesy of HYUNDAI MOTOR AMERICA
    4. Tighten the alternator mounting bolts with the specified torque.

      Tightening torque 

      M10 bolt:

      29.4 ~ 41.2 N.m (3.0 ~ 4.2 kgf.m, 21.7 ~ 30.4 lb-ft)

      M8 bolt:

      21.6 ~ 32.4 N.m (2.2 ~ 3.3 kgf.m, 15.9 ~ 23.9 lb-ft)

  16. Install the engine mounting support bracket.
    1. Install the engine mounting support bracket (B)

      Tightening torque 

      Nut (C):

      78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)

      Bolt (D) and Nuts (E):

      78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)

    2. Connect the engine ground line (A)

      Tightening torque 

      10.8 ~ 13.7 N.m (1.1 ~ 1.4 kgf.m, 8.0 ~ 10.1 lb-ft)

      Fig 26: Identifying Engine Ground Line, Bolts And Nut
      G09815316Courtesy of HYUNDAI MOTOR AMERICA
    3. Remove the jack from the lower crankcase.
  17. Install the oil pan. (Refer to ENGINE LUBRICATION SYSTEM - 2.0L article)
  18. Install cylinder head cover.
    1. The hardening sealant located on the cylinder head cover and the gap between the timing chain cover and the cam carrier should be removed before assembling cylinder head cover.
    2. Apply engine oil on the lip portion of the oil seal on the cover and outer surface of the spark plug pipes.
    3. After applying sealant on the gap between the timing chain cover and the cam carrier, it should be assembled within 5 minutes.

      Bead width:  2.0 ~ 3.0 mm (0.08 ~ 0.12 in.)

      Sealant:  Threebond 1217H or equivalent

      Fig 27: Applying Engine Oil On Lip Portion Of Oil Seal On Cover
      G09815317Courtesy of HYUNDAI MOTOR AMERICA
    4. Install the cylinder head cover (A) by tightening the bolts, in several passes, in the sequence as shown in illustration.

      Tightening torque 

      1st step: 3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)

      2nd step: 7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

      Fig 28: Cylinder Head Cover Bolts Tightening Sequence
      G09815318Courtesy of HYUNDAI MOTOR AMERICA
      CAUTION:
      • Do not reuse cylinder head cover gasket.
      • Before installing the cylinder head cover, make sure the cylinder head cover gasket is not separated from the cylinder head cover gasket groove.
      • The engine running or pressure test should not be performed within 30 minutes after the cylinder head cover was assembled.
  19. Install the high pressure fuel pump (A) and the roller tappet (B). (Refer to HIGH PRESSURE FUEL PUMP )

    Tightening torque: 

    12.7 ~ 14.7 N.m (1.3 ~ 1.5 kgf.m, 9.4 ~ 10.8 lb-ft)

    Fig 29: Identifying High Pressure Fuel Pump And Roller Tappet
    G09815319Courtesy of HYUNDAI MOTOR AMERICA
  20. Install the high pressure pipe (A) and the PCSV (Purge Control Solenoid Valve) bracket (B). (Refer to HIGH PRESSURE FUEL PUMP )

    Tightening torque 

    High pressure pipe nuts:

    26.5 ~ 32.4 N.m (2.7 ~ 3.3 kgf.m, 19.5 ~ 23.9 lb-ft)

    Bracket bolt:

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 30: Identifying High Pressure Pipe And Purge Control Solenoid Valve Bracket
    G09815320Courtesy of HYUNDAI MOTOR AMERICA
  21. Install the vacuum pipe (A).

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 31: Identifying Vacuum Pipe
    G09815321Courtesy of HYUNDAI MOTOR AMERICA
  22. Connect the fuel hose (A) and PCSV (Purge Control Solenoid Valve) hose (B).
    Fig 32: Identifying Fuel And Purge Control Solenoid Valve Hose
    G09815322Courtesy of HYUNDAI MOTOR AMERICA
  23. Install the oil level gauge (A).
    Fig 33: Identifying Oil Level Gauge
    G09815323Courtesy of HYUNDAI MOTOR AMERICA
  24. Install the ignition coils (A).

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 34: Identifying Ignition Coils
    G09815324Courtesy of HYUNDAI MOTOR AMERICA
  25. Connect the PCV (Positive crankcase ventilation) hose (A).
    Fig 35: Identifying Positive Crankcase Ventilation Hose
    G09815325Courtesy of HYUNDAI MOTOR AMERICA
  26. Install the high pump foam (A).
    Fig 36: Identifying High Pump Foam
    G09815326Courtesy of HYUNDAI MOTOR AMERICA
  27. Install the wiring and protectors on the cylinder head cover and then connect the wiring connectors and harness clamps.
    1. The intake OCV (Oil control valve) connector (A)
      Fig 37: Identifying Intake OCV (Oil Control Valve) Connector
      G09815327Courtesy of HYUNDAI MOTOR AMERICA
    2. The exhaust OCV (Oil control valve) connector (A)
      Fig 38: Identifying Exhaust OCV (Oil Control Valve) Connector
      G09815328Courtesy of HYUNDAI MOTOR AMERICA
    3. The alternator connector (A)
      Fig 39: Identifying Alternator Connector
      G09815329Courtesy of HYUNDAI MOTOR AMERICA
    4. The ignition coil connectors (A)
    5. The fuel pump connector (B)
      Fig 40: Identifying Ignition Coil And Fuel Pump Connector
      G09815330Courtesy of HYUNDAI MOTOR AMERICA
    6. The intake CMPS (Camshaft position sensor) connector (A)
    7. The exhaust CMPS (Camshaft position sensor) connector (B)
      Fig 41: Identifying Intake And Exhaust CMPS Connector
      G09815331Courtesy of HYUNDAI MOTOR AMERICA
  28. Install the engine cover. (Refer to ENGINE AND TRANSAXLE ASSEMBLY )
  29. Install the RH side cover (A).

    Tightening torque: 

    3.9 ~ 5.9 N.m (0.4 ~ 0.6 kgf.m, 2.9 ~ 4.3 lb-ft)

    Fig 42: Identifying RH Side Cover
    G09815332Courtesy of HYUNDAI MOTOR AMERICA
  30. Install the under cover. (Refer to ENGINE AND TRANSAXLE ASSEMBLY )
  31. Install the RH front wheel. (Refer to WHEEL )
  32. Connect the battery negative terminal. (Refer to ENGINE AND TRANSAXLE ASSEMBLY )
  33. Install the air duct and cleaner assembly. (Refer to ENGINE AND TRANSAXLE ASSEMBLY )
  34. Add all the necessary fluids and check for leaks. Connect GDS. Check for codes, note, and clear. Recheck.
    NOTE:
    • Refill engine with engine oil.
    • Clean battery posts and cable terminals and assemble.
    • Inspect for fuel leakage.
      • After assembling the fuel line, turn on the ignition switch (do not operate the starter) so that the fuel pump runs for approximately two seconds and fuel line pressurizes.
      • Repeat this operation two or three times, then check for fuel leakage at any point in the fuel line.