LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2014 >> Tucson SE, 4WD >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Timing System - 2.4L >> Timing Chain >> Repair Procedures >> Installation

Repair Procedures: Installation

  1. Install the balance shaft chain.

    (Refer to "BALANCE SHAFT & OIL PUMP ")

  2. Install the crankshaft chain sprocket (B) and the timing chain oil jet (A).

    Tightening torque: 

    7.8 ~ 9.8 N.m (0.8 ~ 1.0 kgf.m, 5.8 ~ 7.2 lb-ft)

    Fig 1: Identifying Timing Chain Oil Jet And Crankshaft Chain Sprocket
    G09802005Courtesy of HYUNDAI MOTOR AMERICA
  3. Set the crankshaft so that the key (A) of crankshaft will be aligned with the mating surface of main bearing cap. Put the intake and exhaust camshaft assembly so that the TDC marks (B) of the intake and exhaust CVVT sprockets will be aligned with the top surface of cylinder head. As a result of this, the piston of No. 1 cylinder is placed at the top dead center on compression stroke.
    Fig 2: Identifying Crankshaft Key
    G09802006Courtesy of HYUNDAI MOTOR AMERICA
    Fig 3: Identifying TDC Marks Of Intake And Exhaust CVVT Sprockets
    G09802007Courtesy of HYUNDAI MOTOR AMERICA
  4. Install the timing chain guide (A).

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 4: Identifying Timing Chain Guide
    G09802008Courtesy of HYUNDAI MOTOR AMERICA
  5. Install the timing chain. To install the timing chain with no slack between each shaft (cam, crank), follow the following procedure. Crankshaft sprocket (A) → Timing chain guide (B) → Intake CVVT sprocket (C) → Exhaust CVVT sprocket (D).
    Fig 5: Identifying Crankshaft Sprocket
    G09802009Courtesy of HYUNDAI MOTOR AMERICA
    NOTE: The timing marks of each sprocket should be matched with timing marks (color link) of timing chain when installing the timing chain.
    Fig 6: Identifying Crankshaft Sprocket At Camshafts
    G09802010Courtesy of HYUNDAI MOTOR AMERICA
    Fig 7: Identifying Sprocket Timing Mark At Crankshaft
    G09802011Courtesy of HYUNDAI MOTOR AMERICA
  6. Install the timing chain tensioner arm (A).

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 8: Identifying Timing Chain Tensioner Arm
    G09802012Courtesy of HYUNDAI MOTOR AMERICA
  7. Install the timing chain auto tensioner (B) and remove the stopper pin (A).

    Tightening torque: 

    9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

    Fig 9: Identifying Timing Chain Auto Tensioner And Stopper Pin
    G09802013Courtesy of HYUNDAI MOTOR AMERICA
  8. After rotating crankshaft 2 revolutions in regular direction (clockwise viewed from front), confirm that the TDC marks (A) on the intake and exhaust CVVT sprockets aligned with the top surface of cylinder head.
    Fig 10: Identifying TDC Marks On Intake And Exhaust CVVT Sprockets
    G09802014Courtesy of HYUNDAI MOTOR AMERICA
  9. Install the timing chain cover.

    (Refer to "TIMING CHAIN COVER ")

  10. Install cylinder head cover.

    (Refer to "CYLINDER HEAD COVER ")

  11. Add all the necessary fluids and check for leaks. Connect GDS. Check for codes, note, and clear. Recheck.
    NOTE:
    • Refill engine with engine oil.
    • Refill a transaxle with fluid.
    • Refill a radiator and a reservoir tank with engine coolant.
    • Clean battery posts and cable terminals and assemble.
    • Inspect for fuel leakage.
      • After assemble the fuel line, turn on the ignition switch (do not operate the starter) so that the fuel pump runs for approximately two seconds and fuel line pressurizes.
      • Repeat this operation two or three times, then check for fuel leakage at any point in the fuel line.
    • Refill radiator and reservoir tank with engine coolant.
    • Bleed air from the cooling system.