LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2014 >> Elantra Coupe Automatic Trans >> Repair and Diagnosis >> Steering >> Electronic Steering >> Motor Driven Power Steering System >> Steering Gear Box >> Repair Procedures >> Replacement

Repair Procedures: Replacement

  1. Remove the front wheel & tire.

    Tightening torque: 

    88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.6 lb-ft)

    Fig 1: Front Wheel & Tire
    G10253850Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION: Be careful not to damage to the hub bolts when removing the front wheel & tire.
  2. Disconnect the stabilizer link (A) with the front strut assembly after loosening the nut.

    Tightening torque: 

    98.1 ~ 117.7 N.m (10.0 ~ 12.0 kgf.m, 72.3 ~ 86.8 lb-ft)

    Fig 2: Disconnecting Stabilizer Link
    G10253851Courtesy of HYUNDAI MOTOR AMERICA
  3. Loosen the nut and then remove the tie-rod end with the front axle (A).

    Tightening torque: 

    23.5 ~ 33.3 N.m (2.4 ~ 3.4 kgf.m, 19.4 ~ 24.6 lb-ft)

    Fig 3: Removing Tie-Rod End
    G10253852Courtesy of HYUNDAI MOTOR AMERICA
  4. Loosen the nut and then remove the lower arm (A).

    Tightening torque: 

    78.5 ~ 88.3 N.m (8.0 ~ 9.0 kgf.m, 57.9 ~ 65.1 lb-ft)

    Fig 4: Removing Lower Arm
    G10253853Courtesy of HYUNDAI MOTOR AMERICA
  5. Loosen the bolt and then disconnect the universal joint assembly (A) from the pinion of the steering gear box.

    Tightening torque: 

    32.4 ~ 37.3 N.m (3.3 ~ 3.8 kgf.m, 23.9 ~ 27.5 lb-ft)

    Fig 5: Universal Joint Assembly Bolt
    G10253854Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION: Lock the steering wheel in the straight ahead position to prevent the damage of the clock spring inner cable when you handle the steering wheel.
  6. Remove the rubber hanger (A).
    Fig 6: Rubber Hanger
    G10253855Courtesy of HYUNDAI MOTOR AMERICA
  7. Remove the cross member from the body by loosening the roll rod (A) mounting bolts and nuts.

    Tightening torque: 

    53.9 ~ 63.7 N.m (5.5 ~ 6.5 kgf.m, 39.8 ~ 47.0 lb-ft)

    Fig 7: Removing Roll Rod Mounting Bolts And Nuts
    G10253856Courtesy of HYUNDAI MOTOR AMERICA
  8. Loosen the bolts & nuts and then remove the front sub frame (A).

    Tightening torque: 

    156.9 ~ 176.5 N.m (16.0 ~ 18.0kgf.m, 115.7 ~ 130.2lb-ft)

    Fig 8: Supporting Front Sub Frame
    G10253857Courtesy of HYUNDAI MOTOR AMERICA
    Fig 9: Removing Front Sub Frame (1 Of 4)
    G10253858Courtesy of HYUNDAI MOTOR AMERICA
    Fig 10: Removing Front Sub Frame (2 Of 4)
    G10253859Courtesy of HYUNDAI MOTOR AMERICA
    Fig 11: Removing Front Sub Frame (3 Of 4)
    G10253860Courtesy of HYUNDAI MOTOR AMERICA
    Fig 12: Removing Front Sub Frame (4 Of 4)
    G10253861Courtesy of HYUNDAI MOTOR AMERICA
  9. Remove the protector (A) & steering gearbox (B) from the front sub frame by loosening the mounting bolts.

    Tightening torque: 

    58.8 ~ 78.8 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)

    Fig 13: Removing Protector And Steering Gearbox
    G10253862Courtesy of HYUNDAI MOTOR AMERICA
  10. Installation is the reverse of the removal.
  11. Check the alignment.

    (Refer to 'TIRES/WHEELS - ALIGNMENT ')