LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2014 >> Elantra Coupe Automatic Trans >> Repair and Diagnosis >> Steering >> Electronic Steering >> Motor Driven Power Steering System >> MDPS Assembly >> Repair Procedures >> Replacement

Repair Procedures: Replacement

  1. Disconnect the battery negative cable from the battery and then wait for at least 30 seconds.
  2. Turn the steering wheel so that the front wheels can face straight ahead.
  3. Push the pins (A).
    Fig 1: Steering Column And Shaft Pins (1 Of 3)
    G10253828Courtesy of HYUNDAI MOTOR AMERICA
    Fig 2: Steering Column And Shaft Pins (2 Of 3)
    G10253829Courtesy of HYUNDAI MOTOR AMERICA
    Fig 3: Steering Column And Shaft Pins (3 Of 3)
    G10253830Courtesy of HYUNDAI MOTOR AMERICA
  4. Disconnect the horn (B) & air bag (A) connector and then remove the air bag module.
    Fig 4: Horn And Air Bag Connector
    G10253831Courtesy of HYUNDAI MOTOR AMERICA
  5. Loosen the lock nut (A), disconnect the connector (B) and then remove the steering wheel.
    Fig 5: Lock Nut And Connector
    G10253832Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION: Do not hammer on the steering wheel to remove it; it may damage the steering column.
  6. Loosen the screw and then remove the steering column upper (A) and lower shroud (B).
    Fig 6: Steering Column Upper And Lower Shroud Screws (1 Of 2)
    G10253833Courtesy of HYUNDAI MOTOR AMERICA
    Fig 7: Steering Column Upper And Lower Shroud Screws (2 Of 2)
    G10253834Courtesy of HYUNDAI MOTOR AMERICA
  7. Disconnect the connector and then remove the clock spring (A).
    Fig 8: Clock Spring Connector
    G10253835Courtesy of HYUNDAI MOTOR AMERICA
    Fig 9: Clock Spring And Connector
    G10253836Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • When assembling set the center position by setting the marks between the clock spring and the cover into line. Make an array the mark by turning the clock spring clockwise to the stop and then 2.0 revolutions counterclockwise.
  8. Loosen the screw and then remove the multifunction switches (A).
    Fig 10: Removing Multifunction Switch (1 Of 3)
    G10253837Courtesy of HYUNDAI MOTOR AMERICA
    Fig 11: Removing Multifunction Switch (2 Of 3)
    G10253838Courtesy of HYUNDAI MOTOR AMERICA
    Fig 12: Removing Multifunction Switch (3 Of 3)
    G10253839Courtesy of HYUNDAI MOTOR AMERICA
  9. Remove the crash pad side cover (A), Fuse box cover and lower crash pad (B).
    Fig 13: Crash Pad Side Cover
    G10253840Courtesy of HYUNDAI MOTOR AMERICA
    Fig 14: Fuse Box Cover And Lower Crash Pad
    G10253841Courtesy of HYUNDAI MOTOR AMERICA
  10. Loosen the bolts and then remove the reinforce panel (A).
    Fig 15: Reinforce Panel With Bolts
    G10253842Courtesy of HYUNDAI MOTOR AMERICA
  11. Loosen the bolt and then disconnect the universal joint assembly (A) from the pinion of the steering gear box.

    Tightening torque: 

    32.4 ~ 37.3 N.m (3.3 ~ 3.8 kgf.m, 23.9 ~ 27.5 lb-ft)

    Fig 16: Universal Joint Assembly And Bolt
    G10253843Courtesy of HYUNDAI MOTOR AMERICA
    CAUTION:
    • Lock the steering wheel in the straight ahead position to prevent the damage of the clock spring inner cable when you handle the steering wheel.
    • Change to the new bolt when assembling
  12. Disconnect all connectors connected the steering column & EPS unit assembly.
  13. Remove the shower duct (A).
    Fig 17: Shower Duct
    G10253844Courtesy of HYUNDAI MOTOR AMERICA
  14. Remove the steering column & EPS unit assembly by loosening the mounting bolt (B) and nuts (A).

    Tightening torque: 

    12.7 ~ 17.7 N.m (1.3 ~ 1.8 kgf.m, 9.4 ~ 13.0 lb-ft)

    Fig 18: Removing Steering Column And EPS Unit Assembly (1 Of 2)
    G10253845Courtesy of HYUNDAI MOTOR AMERICA

    Tightening torque: 

    44.1 ~ 49.0 N.m (4.5 ~ 5.0 kgf.m, 32.5 ~ 36.2 lb-ft)

    Fig 19: Removing Steering Column And EPS Unit Assembly (2 Of 2)
    G10253846Courtesy of HYUNDAI MOTOR AMERICA
  15. Installation is the reverse of the removal.