LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2014 >> Elantra Coupe Automatic Trans >> Repair and Diagnosis >> Body & Frame >> Windows >> Interior >> Crash Pad >> Repair procedures >> Replacement >> Main Crash Pad Replacement

Main Crash Pad Replacement

CAUTION:
  • When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
  • Put on gloves to protect your hands.
  1. Remove the following items.
    1. Front seat

      (Refer to "FRONT SEAT ")

    2. Front pillar trim

      (Refer to "INTERIOR TRIM ")

    3. Floor console assembly

      (Refer to "CONSOLE ")

    4. Front door scuff trim

      (Refer to "INTERIOR TRIM ")

    5. Cowl side trim

      (Refer to "INTERIOR TRIM ")

    6. Crash pad center garnish
    7. Crash pad side cover
    8. Crash pad lower panel
    9. Cluster fascia upper panel & Cluster assembly
    10. Center fascia panel
    11. Audio assembly
    12. Heater control unit
    13. Center crash pad passenger's panel
    14. Glove box & Glove box housing
    15. Steering column

      (Refer to "STEERING COLUMN AND SHAFT ")

  2. After loosening the mounting screw, nut, clip, then remove the console side cover (A).
    Fig 1: Loosening Console Side Cover Mounting Screw, Nut And Clip
    G10254279Courtesy of HYUNDAI MOTOR AMERICA
  3. Disconnect the connector (A).
    Fig 2: Connector
    G10254280Courtesy of HYUNDAI MOTOR AMERICA
  4. After loosening the mounting screw, then remove the center crash pad passenger's panel (A).
    Fig 3: Center Crash Pad Passenger Panel
    G10254281Courtesy of HYUNDAI MOTOR AMERICA
  5. Using a screwdriver or remover, remove the center crash pad driver's panel [RH] (A).
    Fig 4: Center Crash Pad Driver Panel (RH)
    G10254282Courtesy of HYUNDAI MOTOR AMERICA
  6. Disconnect the connector (A).
    Fig 5: Connector
    G10254283Courtesy of HYUNDAI MOTOR AMERICA
  7. After loosening the mounting screws, then remove the center crash pad driver's panel [LH] (A).
    Fig 6: Center Crash Pad Driver Panel (LH)
    G10254284Courtesy of HYUNDAI MOTOR AMERICA
  8. Disconnect the connectors (A).
    Fig 7: Connectors
    G10254285Courtesy of HYUNDAI MOTOR AMERICA
  9. Disconnect the passengers airbag connectors (A).
  10. Loosen the mounting bolts.
    Fig 8: Passengers Airbag Connectors
    G10254286Courtesy of HYUNDAI MOTOR AMERICA
  11. Using a screwdriver or remover, remove the photo sensor (A).
  12. Disconnect the photo sensor connector (B).
    Fig 9: Photo Sensor Connector
    G10254287Courtesy of HYUNDAI MOTOR AMERICA
  13. Disconnect the connector (A).
    Fig 10: Connector
    G10254288Courtesy of HYUNDAI MOTOR AMERICA
  14. After loosening the mounting bolts and nuts, screw, then remove the main crash pad assembly (A).
    Fig 11: Loosening Main Crash Pad Assembly Mounting Bolts And Nuts
    G10254289Courtesy of HYUNDAI MOTOR AMERICA
  15. Installation is the reverse of removal.
    NOTE:
    • Make sure the crash pad fits onto the guide pins correctly.
    • Before tightening the bolts, make sure the crash pad wire harnesses are not pinched.
    • Make sure the connectors are plugged in properly, and the antenna lead is connected properly.
    • Enter the anti-theft code for the radio, then enter the customers radio station presets.