LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2010 >> Accent GLS, Standard >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Cylinder Block >> Repair Procedures >> Reassembly

Repair Procedures: Reassembly

NOTE:
  • Thoroughly clean all parts to assembled.
  • Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.
  • Replace all gaskets, O-rings and oil seals with new parts.
  1. Assemble the piston and connecting rod.
    1. Use a hydraulic press for installation
    2. The piston front mark and the connecting rod front mark must face the timing belt side of the engine.
      Fig 1: Identifying Piston Front Mark And Connecting Rod Front Mark Must Face Timing Belt Side Of Engine
      G06879171Courtesy of HYUNDAI MOTOR CO.
  2. Install the piston rings.
    1. Install the oil ring expander and 2 side rails by hand.
    2. Using a piston ring expander, install the 2 compression rings with the code mark facing upward.
    3. Position the piston rings so that the ring ends are as shown.
      Fig 2: Identifying Piston Ring End Positions
      G06879172Courtesy of HYUNDAI MOTOR CO.
  3. Install the connecting rod bearings.
    1. Align the bearing (A) claw with the groove of the connecting rod or connecting rod cap (B).
    2. Install the bearings (A) in the connecting rod and connecting rod cap (B).
      Fig 3: Locating Bearings And Connecting Rod Cap
      G06879173Courtesy of HYUNDAI MOTOR CO.
  4. Install the crankshaft main bearings.
    NOTE: Upper bearings have an oil groove of oil holes; Lower bearings do not.
    1. Align the bearing claw with the claw groove of the cylinder block, push in the 4 upper bearings (A).
      Fig 4: Locating Upper Bearings
      G06879174Courtesy of HYUNDAI MOTOR CO.
    2. Align the bearing claw with the claw groove of the main bearing cap, and push in the 5 lower bearings.
  5. Install the center bearing.

    Install the center bearing (A) under the No. 3 journal position of the cylinder block with the oil grooves facing outward.

    Fig 5: Locating Center Bearing
    G06879175Courtesy of HYUNDAI MOTOR CO.
  6. Place the crankshaft on the cylinder block.
  7. Place the main bearing caps on the cylinder block.
  8. Install the main bearing cap bolts.
    NOTE: The main bearing cap bolts are tightened in 2 progressive steps.
    If any of the bearing cap bolts in broken or deformed, replace it.
    1. Apply a light coat of engine oil on the threads and under the bearing cap bolts.
    2. Install and uniformly tighten the 10 bearing cap bolts (A), in several passes, in the sequence shown.

      Tightening torque: 

      53.9 ~ 58.8 N.m (5.5 ~ 6.0 kgf.m, 39.8 ~ 43.4 lb-ft)

      Fig 6: Bearing Cap Bolts Tightening Sequence
      G06879176Courtesy of HYUNDAI MOTOR CO.
    3. Check that the crankshaft turns smoothly.
  9. Check the crankshaft end play.
  10. Install the piston and connecting rod assemblies.
    NOTE: Before installing the piston, apply a coat of engine oil to the ring grooves and cylinder bores.
    1. Remove the connecting rod caps, and slip short sections of rubber hose over the threaded ends of the connecting rod bolts
    2. Install the ring compressor, check that the rings are securely in place, then position the piston in the cylinder, and tap it in using the wooden handle of a hammer.
    3. Stop after the ring compressor pops free, and check the connecting rod-to-crank journal alignment before pushing the piston into place.
    4. Apply engine oil to the bolt threads. install the rod caps with bearings, and tighten the nuts.

      Tightening torque: 

      31.4 ~ 34.3 N.m (3.2 ~ 3.5 kgf.m, 23.1 ~ 25.3 lb-ft)

      NOTE: Maintain downward force on the ring compressor to prevent the rings from expending before entering the cylinder bore.
      Fig 7: Installing Piston And Connecting Rod Assemblies
      G06879177Courtesy of HYUNDAI MOTOR CO.
  11. Install the rear oil seal case.
    1. Using a razor blade and gasket scraper, remove all the old packing material from the gasket surfaces.
      NOTE: Check that the mating surfaces are clean and dry before applying liquid gasket.
    2. Apply liquid gasket as an even bead, centered between the edges of the mating surface.

      Liquid gasket:  LOCTITE 5900 or equivalent

    3. Install the rear oil seal case (A) with 5 bolts (B).

      Tightening torque: 

      9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

      Fig 8: Locating Rear Oil Seal Case And Bolts
      G06879178Courtesy of HYUNDAI MOTOR CO.
  12. Install the rear oil seal.
    1. Apply engine oil to a new oil seal lip.
    2. Using the SST (09231-21000) and a hammer, tap in the oil seal until its surface is flush with the rear oil seal retainer edge.
      Fig 9: Installing Rear Oil Seal
      G06879179Courtesy of HYUNDAI MOTOR CO.
  13. Install the front case.
  14. Install the oil screen.

    Install a new gasket (B) and oil screen (A) with 2 bolts (C).

    Tightening torque: 

    14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

    Fig 10: Locating Gasket, Oil Screen And Bolts
    G06879180Courtesy of HYUNDAI MOTOR CO.
  15. Install the oil pan.
    1. Using a razor blade and gasket scraper, remove all the old packing material from the gasket surfaces.
      NOTE: Check that the mating surfaces are clean and dry before applying liquid gasket.
    2. Apply liquid gasket as an even bead, centered between the edges of the mating surface.

      Liquid gasket:  TB1217H or equivalent

      NOTE:
      • To prevent leakage of oil, apply liquid gasket to the inner threads of the bolt holes.
      • D not install the parts if five minutes or more have elapsed since applying the liquid gasket.

        Instead, reapply liquid gasket after removing the residue.

      • After assembly, wait at least 30 minutes before filling the engine with oil.
    3. Install the oil pan (A) with the bolts.

      Uniformly tighten the bolts in several passes.

      Tightening torque: 

      9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

      Fig 11: Locating Oil Pan
      G06879181Courtesy of HYUNDAI MOTOR CO.
  16. Install the water pump.
  17. Install the oil pressure switch.
    1. Apply adhesive to 2 or 3 threads.

      Adhesive:  TB 2310/2350 or equivalent.

    2. Install the oil pressure switch (A).

      Tightening torque: 

      14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.8 ~ 15.9 lb-ft)

      Fig 12: Locating Oil Pressure Switch
      G06879182Courtesy of HYUNDAI MOTOR CO.
  18. Install the knock sensor (A).

    Tightening torque: 

    16.7 ~ 26.5 N.m (1.7 ~ 2.7 kgf.m, 12.3 ~ 19.5 lb-ft)

    Fig 13: Locating Knock Sensor
    G06879183Courtesy of HYUNDAI MOTOR CO.
  19. Install the oil level gauge tube (A).
    1. Install a new O-ring on the oil level gauge tube.
    2. Apply engine oil on the O-ring.
    3. Install the oil level gauge tube (A) with the bolt.

      Tightening torque: 

      11.8 ~ 14.7 N.m (1.2 ~ 1.5 kgf.m, 8.7 ~ 10.8 lb-ft)

      Fig 14: Locating Oil Level Gauge Tube
      G06879184Courtesy of HYUNDAI MOTOR CO.
  20. Install the cylinder head.
  21. Install the timing belt.
  22. Remove the engine stand.
  23. A/T: install the drive plate.

    Tightening torque: 

    117.7 ~ 127.5 N.m (12.0 ~ 13.0 kgf.m, 86.8 ~ 94.0 lb-ft)

    Fig 15: Locating Drive Plate
    G06879185Courtesy of HYUNDAI MOTOR CO.
  24. M/T: install the fly wheel.

    Tightening torque: 

    117.7 ~ 127.5 N.m (12.0 ~ 13.0 kgf.m, 86.8 ~ 94.0 lb-ft)