LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2007 >> Santa Fe SE, AWD >> Repair and Diagnosis >> General Information >> OEM General Information >> General >> General Service Information >> Servicing The Electrical System

Servicing The Electrical System

  1. Prior to servicing the electrical system, be sure to turn off the ignition switch and disconnect the battery ground cable.
    NOTE: In the course of MFI or ELC system diagnosis, when the battery cable is removed, any diagnostic trouble code retained by the computer will be cleared. There fore, if necessary, record the diagnostic data before removing the battery cable.
    Fig 1: Disconnecting Battery Ground Cable
    G05347454Courtesy of HYUNDAI MOTOR CO.
  2. Attach the wiring harnesses with clamps so that there is no slack. However, for any harness which passes the engine or other vibrating parts of the vehicle, allow some slack within a range that does not allow the engine vibrations to cause the harness to come into contact with any of the surrounding parts and then secure the harness by using a clamp.
    Fig 2: Checking Wiring Clamp
    G05347455Courtesy of HYUNDAI MOTOR CO.
  3. If any section of a wiring harness interferes with the edge of a parts, or a corner, wrap the section of the harness with tape or something similar in order to protect if from damage.
    Fig 3: Wrapping Section Of Harness With Tape
    G05347456Courtesy of HYUNDAI MOTOR CO.
  4. When installing any parts, be careful not to pinch or damage any of the wiring harness.
    Fig 4: Identifying Pinch Or Damage Of Wiring Harness
    G05347457Courtesy of HYUNDAI MOTOR CO.
  5. Never throw relays, sensors or electrical parts, or expose them to strong shock.
    Fig 5: Precaution For Relays, Sensors Or Electrical Parts
    G05347458Courtesy of HYUNDAI MOTOR CO.
  6. The electronic parts used in the computer, relays, etc. are readily damaged by heat. If there is a need for service operations that may cause the temperature to exceed 80°C (176°F), remove the electronic parts before hand.
    Fig 6: Precaution For Electronic Parts
    G05347459Courtesy of HYUNDAI MOTOR CO.
  7. Loose connectors cause problems. Make sure that the connectors are always securely fastened.
    Fig 7: Electronic Parts Connectors
    G05347460Courtesy of HYUNDAI MOTOR CO.
  8. When disconnecting a connector, be sure to grip only the connector, not the wires.
    Fig 8: Disconnecting Connector
    G05347461Courtesy of HYUNDAI MOTOR CO.
  9. Disconnect connector which have catches by pressing in the direction of the arrows shown the illustration.
    Fig 9: Locating Connector Catches
    G05347462Courtesy of HYUNDAI MOTOR CO.
  10. Connect connectors which have catches by inserting the connectors until they make a clicking sound.
    Fig 10: Connecting Connectors
    G05347463Courtesy of HYUNDAI MOTOR CO.
  11. When using a circuit tester to check continuity or voltage on connector terminals, insert the test probe into the harness side. If the connector is a sealed connector, insert the test probe through the hole in the rubber cap until contacts the terminal, being careful not to damage the insulation of the wires.
    Fig 11: Inserting Test Probe Into Harness Side
    G05347464Courtesy of HYUNDAI MOTOR CO.
  12. To avoid overloading the wiring, take the electrical current load of the optional equipment into consideration, and determine the appropriated wire size.
    SAE SPECIFICATIONS

    Nominal size SAE gauge No. Permissible current
    In engine compartment Other areas
    0.3mm2 AWG 22 - 5A
    0.5mm2 AWG 20 7A 13A
    0.85mm2 AWG 18 9A 17A
    1.25mm2 AWG 16 12A 22A
    2.0mm2 AWG 14 16A 30A
    3.0mm2 AWG 12 21A 40A
    5.0mm2 AWG 10 31A 54A