LEMON Manuals: Even more car manuals for everyone
Home >> Hyundai >> 2000 >> Sonata Base, Automatic >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Self-Diagnostics - 2.4L >> Diagnostic Tests >> DTC P0120: Throttle Position (TP) Sensor >> Test Procedures

Test Procedures

  1. Turn ignition on. Install scan tool to data link connector, and verify DTC P0120 is set. If DTC P0120 is set, go to next step. If DTC P0510 is set, poor ground connection or repair open in Black/White wire between TP sensor connector terminal No. 4 and ECM C44-2 (A/T) connector terminal No. 17 or C45-4 (M/T) terminal No. 22. If equipped with A/T and DTC P0100 and/or P1400 is set, repair open in Blue wire between TP sensor connector terminal No. 2 and ECM connector C44-3 (A/T) terminal No. 8. If equipped with M/T and DTC P0100 and/or P1400 is set, repair short to voltage in Blue wire between TP sensor connector terminal No. 2 and ECM C45-4 (M/T) connector terminal No. 14. When repairs are completed, clear DTCs and verify TP sensor operation.
  2. Start engine and allow to idle. Using scan tool, monitor output voltage of TP sensor at idle position. If TP sensor output voltage is less than 0.3 or more than 0.9 volt, go to step  4 . If output voltage is more than 0.9 volt, go to next step. If TP sensor output voltage is about 0.3-0.9 volt, TP sensor is operating properly. Fault is intermittent or was corrected and DTC was not cleared. When repairs are completed, clear DTCs and verify TP sensor operation.
  3. Turn ignition off. Disconnect TP sensor connector. Turn ignition on, engine off. Using scan tool, measure TP sensor output voltage. If voltage is zero, replace TP sensor. If voltage is more than zero volts, repair short to voltage in Blue wire between TP sensor connector terminal No. 2 and ECM connector C44-3 (A/T) terminal No. 8 or C45-4 (M/T) connector terminal No. 14. When repairs are completed, clear DTCs and verify TP sensor operation.
  4. Turn ignition on. Fully release throttle. Loosen TP sensor mounting screws and attempt to adjust TP sensor position. Using scan tool, measure TP sensor output voltage. Adjust (rotate clockwise to increase output voltage) TP sensor until output voltage is 0.4-0.5 volt. If output voltage can not be adjusted, go to step  6 . If output voltage can be adjusted, go to next step.
  5. Tighten TP sensor mounting screws. Turn ignition on. Hold throttle in Wide Open Throttle (WOT) position and measure TP sensor output voltage. If output voltage is about 4.8 volts, problem was a misadjusted TP sensor. If output voltage is not 4.8 volts, replace TP sensor. When repairs are completed, clear DTCs and verify TP sensor operation.
  6. Turn ignition off. Disconnect TP sensor connector. Measure voltage between ground and TP sensor connector terminal No. 1 (Light Blue/Black wire). If 5 volts are present, go to next step. If 5 volts are not present, repair open in Light Blue/Black wire between TP sensor connector terminal No. 1 and ECM C44-2 (A/T) connector terminal No. 6 or C45-4 (M/T) connector terminal No. 11. When repairs are completed, clear DTCs and verify TP sensor operation.
  7. Turn ignition off. Disconnect TP sensor connector. Ensure ECM connector is connected. Measure resistance between ground and TP sensor terminal No. 4 (Black/White wire). If resistance is one ohm or less, go to next step. If resistance is more than one ohm, repair poor ground connection or open in Black/White wire between TP sensor and ECM C44-2 (A/T) connector terminal No. 17 or C45-4 (M/T) connector terminal No. 22. When repairs are completed, clear DTCs and verify TP sensor operation.
  8. Turn ignition off. Disconnect TP sensor connector. Ensure ECM connector is connected. Connect a fused jumper wire between TP sensor connector terminals No. 1 (Light Blue/Black wire) and No. 2 (Blue wire). Turn ignition on. Using a scan tool, measure TP sensor output voltage. If 4.8 volts are not present, go to next step. If 4.8 volts are present, replace TP sensor. When repairs are completed, clear DTCs and verify TP sensor operation.
  9. Turn ignition off. With jumper wire in place and ECM connector connected, backprobe ECM connector. Turn ignition on and measure voltage between ground and ECM C44-2 (A/T) connector terminal No. 6 (Light Blue/Black wire) or C45-4 (M/T) connector terminal No. 11 (Light Blue/Black wire). If voltage is 5 volts, go to next step. If voltage is not 5 volts, repair open or short to ground in Light Blue/Black wire between TP sensor and ECM. When repairs are completed, clear DTCs and verify TP sensor operation.
  10. Reconnect TP sensor connector. Start engine and allow to idle. Using scan tool, monitor idle switch output. If idle switch output is closed with engine at idle and open with engine off idle, go to next step. If idle switch is not closed at engine idle, replace TP sensor. When repairs are completed, clear DTCs and verify TP sensor operation.
  11. Turn ignition off. Disconnect TP sensor connector. Move throttle valve from idle (closed) position to open position. Check for continuity between TP sensor terminals No. 3 and 4. Continuity should exist when throttle valve is in idle (closed) position and not exist when throttle is opened. If continuity is as specified, ensure ECM connector is clean and tight. If connector is okay, replace TP sensor. If problem persists, replace ECM. If continuity is not as specified, replace TP sensor. When repairs are completed, clear DTCs and verify TP sensor operation.