LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2014 >> Civic Hybrid >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> Engine Control System & Engine Mechanical - Testing & Troubleshooting (Hybrid) >> Testing >> Valve Stem-to-Guide Clearance Inspection >> Removal

Valve Stem-to-Guide Clearance Inspection: Removal

  1. Vehicle - Lift 
      1. Raise the vehicle on a lift, and make sure it is securely supported.
  2. HDS DLC - Connection 
    GHH124294Courtesy of HONDA, U.S.A., INC.
    NOTE: For specific operations, refer to the user's manual that came with the Honda Diagnostic System (HDS). Make sure the HDS is loaded with the latest software.

    1. Connect the HDS to the data link connector (DLC) (A) located under the driver's side of the dashboard.

    2. Turn the ignition switch to ON (II).

    3. Make sure the HDS communicates with the vehicle. If it does not communicate, go to the DLC circuit troubleshooting.

  3. Fuel Filler Cap 
      1. Remove the fuel fill cap to relieve the pressure in the fuel tank.
  4. Fuel Pump OFF 
      1. From the INSPECTION MENU of the HDS, select Fuel Pump OFF, then start the engine, and let it idle until it stalls.
    NOTE:
    • Do not allow the engine to idle above 1, 000 rpm or the PCM will continue to operate the fuel pump.
    • Pending or Confirmed DTC may be set during this procedure. Check for DTCs, and clear them as needed.

    2. Turn the ignition switch to LOCK (0).

  5. 12 Volt Battery Terminal - Disconnection 
    GHH124295Courtesy of HONDA, U.S.A., INC.
    1. Make sure the ignition switch is in LOCK (0).

    2. Disconnect and isolate the negative cable with the battery sensor (A) from the 12 volt battery.

    NOTE:
    • Always disconnect the negative side first.
    • To protect the battery sensor connector (B) from damage, do not hold it when removing the negative terminal.
    • Do not disconnect the battery sensor from the negative terminal (C).

    3. Remove the harness clip (E).

    4. Disconnect the positive cable (D) from the 12 volt battery.

  6. Air Cleaner 
    GHH124296Courtesy of HONDA, U.S.A., INC.
    1. Disconnect the intake air duct (A) from the air cleaner (B).

    2. Remove the air cleaner.

  7. Fuel Pressure - Relieving 
    GHH124297Courtesy of HONDA, U.S.A., INC.
    1. Remove the bracket (A).

    2. Remove the quick-connect fitting cover (B).

    3. Check the fuel quick-connect fitting for dirt, and clean it if needed.

    GHH124298Courtesy of HONDA, U.S.A., INC.
    4. Place a rag or shop towel over the quick-connect fitting (A).
    GHH124299Courtesy of HONDA, U.S.A., INC.
    5. Disconnect the quick-connect fitting: Hold the connector (A) with one hand, and squeeze the retainer tabs (B) with the other hand to release them from the locking tabs (C). Pull the connector off.
    NOTE:
    • Be careful not to damage the line (D) or other parts.
    • Do not use tools.
    • If the connector does not move, keep the retainer tabs pressed down, and alternately pull and push the connector until it comes off easily.
    • Do not remove the retainer from the line; once removed, the retainer must be replaced with a new one.
  8. Radiator Cap 
      1. Wait until the engine is cool, then carefully remove the radiator cap.
  9. Radiator Coolant - Drain 
    GHH124300Courtesy of HONDA, U.S.A., INC.
    1. Loosen the drain plug (A), and drain the coolant.

    2. Tighten the radiator drain plug securely.

  10. Engine Cover 
    GHH124301Courtesy of HONDA, U.S.A., INC.
    1. Remove the engine cover.
  11. Intake Air Resonator 
    GHH124302Courtesy of HONDA, U.S.A., INC.
    1. Remove the intake air resonator.
  12. Intake Air Duct 
    GHH124303Courtesy of HONDA, U.S.A., INC.
    1. Remove the intake air duct.
  13. Intake Air Pipe 
    GHH124304Courtesy of HONDA, U.S.A., INC.
    1. Remove the intake air pipe.
  14. Throttle Body - Move 
    GHH124305Courtesy of HONDA, U.S.A., INC.
    1. Remove the throttle body without disconnecting the hoses.
  15. Splash Shield 

    1. Remove the splash shield (A).

    GHH118060Courtesy of HONDA, U.S.A., INC.
  16. Engine Undercover 
    GHH124306Courtesy of HONDA, U.S.A., INC.
    1. Remove the engine undercover (A).
  17. Intake Manifold Bracket 
    GHH124307Courtesy of HONDA, U.S.A., INC.
    1. Remove the intake manifold bracket mounting bolts.
  18. Intake Manifold/Chamber Peripheral Assembly 
    GHH124308Courtesy of HONDA, U.S.A., INC.
    1. Disconnect the connectors (A).

    2. Remove the engine wire harness (B).

  19. Intake Manifold/Chamber Assembly 
    GHH124309Courtesy of HONDA, U.S.A., INC.
    1. Disconnect the PCV hose (A).

    2. Remove the intake manifold/chamber assembly (B).

  20. Ignition Coil 
    GHH124310Courtesy of HONDA, U.S.A., INC.
    1. Disconnect the connectors.

    2. Remove the ignition coils.

  21. Cylinder Head Cover Peripheral Assembly 
    GHH124311Courtesy of HONDA, U.S.A., INC.
    1. Remove the harness holder (A).

    2. Disconnect the breather hose (B).

  22. Cylinder Head Cover and/or Packing 
    GHH124312Courtesy of HONDA, U.S.A., INC.
    1. Remove the cylinder head cover.
  23. Cylinder Head Peripheral Assembly 
    GHH124313Courtesy of HONDA, U.S.A., INC.
    1. Remove the fuel pipe (A).
    GHH124314Courtesy of HONDA, U.S.A., INC.
    2. Disconnect the connectors.
    GHH124315Courtesy of HONDA, U.S.A., INC.
    3. Remove the harness holder.
    GHH124316Courtesy of HONDA, U.S.A., INC.
    4. Remove the bolts.
    GHH124317Courtesy of HONDA, U.S.A., INC.
    5. Disconnect the upper radiator hose (A), the water bypass hose (B), and the heater hose (C).
  24. A/F Sensor 
    GHH124318Courtesy of HONDA, U.S.A., INC.
    1. Disconnect the connector.

    2. Remove the A/F sensor (A).

  25. Wiper Arm Assembly 
    GHH124319Courtesy of HONDA, U.S.A., INC.
    NOTE: Set the wiper arms to the auto-stop position before removal.

    1. Remove the cowl top wiper covers (A).

    2. Remove the wiper arms (B).

  26. Both Side Cowl Covers 
    GHH124320Courtesy of HONDA, U.S.A., INC.
    1. Remove the side cowl cover (A).

    2. The left side is shown; repeat on the right side.

  27. Center Cowl Cover 
    GHH124321Courtesy of HONDA, U.S.A., INC.
    1. Remove the center cowl cover (A).

    2. Disconnect the windshield washer tube (B)

    3. If necessary, remove the hood rear seal (C).

  28. Under Cowl Panel 
    GHH124322Courtesy of HONDA, U.S.A., INC.
    1. Remove the under cowl panel (A).
  29. EGR Pipe 
    GHH124323Courtesy of HONDA, U.S.A., INC.
    1. Remove the EGR pipe (A).
  30. Exhaust Chamber Cover 
    GHH124324Courtesy of HONDA, U.S.A., INC.
    1. Remove the exhaust chamber cover.
  31. WU-TWC Lower Side - Reconnection 
    GHH124325Courtesy of HONDA, U.S.A., INC.
    1. Remove the bolts (A and B).
  32. WU-TWC 
    GHH132769Courtesy of HONDA, U.S.A., INC.
    1. Remove the WU-TWC.
  33. Check the No. 1 Piston at Top Dead Center (With Cam Chain Case/Oil Pump) 
    GHH124326Courtesy of HONDA, U.S.A., INC.
    1. Set the No. 1 piston at top dead center (TDC). The "UP" mark (A) on the camshaft sprocket should be at the top, and the TDC grooves (B) on the camshaft sprocket should line up with the top edge of the head.
  34. Tire and Wheel-Removal, Front Right 
    GHH124327Courtesy of HONDA, U.S.A., INC.
    1. Remove the center cap (A).

    2. Remove the right front wheel.

  35. Water Pump Pulley Mounting Bolt - Loosen 
    GHH124328Courtesy of HONDA, U.S.A., INC.
    1. Loosen the water pump pulley mounting bolts (A).
  36. Drive Belt 
    GHH124329Courtesy of HONDA, U.S.A., INC.
    1. Move the auto-tensioner (A) to relieve tension from the drive belt (B).

    2. Remove the drive belt.

  37. Water Pump Pulley 
    GHH124330Courtesy of HONDA, U.S.A., INC.
    1. Remove the water pump pulley.
  38. Auto Tensioner Assembly 
    GHH124331Courtesy of HONDA, U.S.A., INC.
    1. Remove the drive belt auto-tensioner.
  39. Water Pump 
    GHH124332Courtesy of HONDA, U.S.A., INC.
    1. Remove the water pump.
  40. Crankshaft Pulley 
    GHH124333Courtesy of HONDA, U.S.A., INC.
    1. Hold the pulley with the holder handle (A) and the crankshaft pulley holder (B).

    2. Remove the bolt with a socket, 19 mm (C) and a breaker bar.

    3. Remove the crankshaft pulley.

  41. Engine Jack Support (State Of A Low Vehicle) 
      1. Lift and support the engine with a jack and a wood block under the oil pan.
  42. Side Engine Mount 
    GHH124334Courtesy of HONDA, U.S.A., INC.
    1. Remove the A/C pipe bracket (A).

    2. Remove the ground cable (B).

    3. Remove the side engine mount bracket (C) and the side engine mount assembly (D).

  43. Cam Chain Case 
    GHH124335Courtesy of HONDA, U.S.A., INC.
    1. Remove the cam chain case.
  44. Cam Chain Inspection 
    GHH124336Courtesy of HONDA, U.S.A., INC.
    1. Measure the cam chain separation. If the distance is less than the service limit, replace the cam chain and the cam chain tensioner.
    Standard Distance: 19 mm (0.75 in)
    Service Limit: 15 mm (0.59 in)
  45. Cam Chain Tensioner Slider 
    GHH124337Courtesy of HONDA, U.S.A., INC.
    1. Apply new engine oil to the sliding surface of the cam chain tensioner slider (A).

    2. Hold the cam chain tensioner slider with a screwdriver, then remove the upper bolt (B), and loosen the lower bolt (C).

    GHH124338Courtesy of HONDA, U.S.A., INC.
    3. Remove the cam chain tensioner slider.
  46. Cam Chain Tensioner and Guide 
    GHH124339Courtesy of HONDA, U.S.A., INC.
    1. Remove the cam chain tensioner (A) and the cam chain guide (B).
  47. Cam Chain 
    GHH124340Courtesy of HONDA, U.S.A., INC.
    1. Remove the cam chain.
  48. Cylinder Head Assembly 
    GHH124341Courtesy of HONDA, U.S.A., INC.
    1. Remove the cylinder head bolts. To prevent warpage, loosen the bolts in sequence, 1/3 turn at a time, repeat the sequence until all bolts are loosened.

    2. Remove the cylinder head.

  49. Rocker Arm Assembly 
    GHH124342Courtesy of HONDA, U.S.A., INC.
    1. Loosen the rocker arm adjusting screws (A).
    GHH124343Courtesy of HONDA, U.S.A., INC.
    2. Remove the camshaft holder bolts. To prevent damaging the camshaft, loosen the bolts in sequence two turns at a time.
    GHH124344Courtesy of HONDA, U.S.A., INC.
    3. Remove the rocker arm assembly.
  50. Camshaft 
    GHH124345Courtesy of HONDA, U.S.A., INC.
    1. Remove the camshaft.
  51. Valve Spring 
    GHH124346Courtesy of HONDA, U.S.A., INC.
    1. Using an appropriate-sized socket (A) and a plastic mallet (B), lightly tap the spring retainer to loosen the valve cotters.
    GHH124347Courtesy of HONDA, U.S.A., INC.
    2. Install the valve spring compressor attachment and the valve spring compressor.

    3. Compress the valve spring and remove the valve cotters.

    4. Remove the valve spring compressor and the valve spring compressor attachment.

    5. Remove the spring retainer, the valve spring, and the valve.

  52. Valve Seal 
    GHH124348Courtesy of HONDA, U.S.A., INC.
    1. Install the valve guide seal remover.
    GHH124349Courtesy of HONDA, U.S.A., INC.
    2. Remove the valve seal.
  53. Valve Spring Seat 
      1. Remove the valve spring seat.