LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2014 >> Civic Hybrid >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> Engine Control System & Engine Mechanical - Testing & Troubleshooting (Hybrid) >> Testing >> Camshaft Inspection >> Installation

Camshaft Inspection: Installation

  1. Camshaft 
    GHH124039Courtesy of HONDA, U.S.A., INC.
    1. Install the camshaft.
  2. Rocker Arm Assembly 
    GHH124040Courtesy of HONDA, U.S.A., INC.
    1. Install the rocker arm assembly.
    Fig 1: Rocker Arm Assembly Tightening Sequence
    GHH124041Courtesy of HONDA, U.S.A., INC.
      2. Apply new engine oil to the bolt threads and flange.

    3. Tighten each bolts two turns at a time in sequence.

    Specified Torque:
    8 mm Bolts: 22 N.m (2.2 kgf.m, 16 lbf.ft).
    8 mm Bolts: (11),(13) 20 N.m (2.0 kgf.m, 15 lbf.ft).
    6 mm Bolt: (12) 12 N.m (1.2 kgf.m, 9 lbf.ft).
  3. Cam Chain Sprocket 
    GHH124042Courtesy of HONDA, U.S.A., INC.
    1. Install the cam chain to the camshaft sprocket by aligning the reference mark (A), then install the camshaft sprocket on the camshaft.
    GHH124043Courtesy of HONDA, U.S.A., INC.
    2. Hold the camshaft with a 27 mm open-end wrench.

    3. Tighten the camshaft sprocket mounting bolt.

    NOTE: Apply new engine oil to the bolt threads and flange.
    Specified Torque:
    56 N.m (5.7 kgf.m, 41 lbf.ft)
    GHH124044Courtesy of HONDA, U.S.A., INC.
    4. Apply new engine oil to the slider surface of the cam chain tensioner slider through the oil return hole in the cylinder head.
    GHH124045Courtesy of HONDA, U.S.A., INC.
    5. Hold the crankshaft pulley, and set the socket wrench (A) on the camshaft sprocket bolt.

    6. Turn the camshaft clockwise to compress the cam chain tensioner.

    7. Remove the 6 x 1.0 mm bolt (B).

    NOTE:
    • The turning torque should not exceed 44 N•m (4.5 kgf•m, 33 lbf•ft) when turning the camshaft.
    • Do not turn the camshaft counterclockwise.

    8. Install the maintenance bolt (C) with a new washer (D).

    GHH124046Courtesy of HONDA, U.S.A., INC.
    9. Install the new cylinder head plug.
  4. Valve Clearance Adjustment 
    GHH124047Courtesy of HONDA, U.S.A., INC.
    1. Set the No. 1 piston at top dead center (TDC). The "UP" mark (A) on the camshaft sprocket should be at the top, and the TDC grooves (B) on the camshaft sprocket should line up with the top edge of the head.

    2. Select the correct feeler gauge for the valve clearance you are going to check.

    Valve Clearance
    Intake: 0.15-0.19 mm (0.006-0.007 in)
    Exhaust: 0.24-0.28 mm (0.010-0.011 in)
    GHH118042Courtesy of HONDA, U.S.A., INC.
    GHH124048Courtesy of HONDA, U.S.A., INC.
    3. Insert the feeler gauge (A) between the adjusting screw (B) and the end of the valve stem on the No. 1 cylinder, and slide it back and forth; you should feel a slight amount of drag.
    GHH124049Courtesy of HONDA, U.S.A., INC.
    4. If you feel too much or too little drag, loosen the locknut, and turn the adjusting screw (A) until the drag on the feeler gauge is correct.

    5. While holding the adjusting screw with the screw driver, tighten the locknut, then recheck the clearance. Repeat the adjustment, if necessary.

    Specified Torque
    20 N.m (2.0 kgf.m, 15 lbf.ft)
    Apply new engine oil to the nut threads.
    GHH124050Courtesy of HONDA, U.S.A., INC.
    6. Rotate the crankshaft clockwise. Align the No. 3 piston TDC groove (A) on the camshaft sprocket with the top edge of the head.

    7. Check and, if necessary, adjust the valve clearance on the No. 3 cylinder.

    GHH124051Courtesy of HONDA, U.S.A., INC.
    8. Rotate the crankshaft clockwise. Align the No. 4 piston TDC groove (A) on the camshaft sprocket with the top edge of the head

    9. Check and, if necessary, adjust the valve clearance on the No. 4 cylinder.

    GHH124052Courtesy of HONDA, U.S.A., INC.
    10. Rotate the crankshaft clockwise. Align the No. 2 piston TDC groove (A) on the camshaft sprocket with the top edge of the head

    11. Check and, if necessary, adjust the valve clearance on the No. 2 cylinder.

  5. Cylinder Head Cover and/or Packing 
    GHH124053Courtesy of HONDA, U.S.A., INC.
    1. Check the spark plug seals (A) for damage. If the seal is damaged, replace it.

    2. Thoroughly clean the head cover gasket (B) and the groove.

    NOTE: Check and, if necessary, replace the head cover gasket.

    3. Install the head cover gasket in the groove of the cylinder head cover (C).

    4. Make sure the head cover gasket is evenly seated securely.

    5. Remove the old liquid gasket from the chain case.

    6. Clean the head cover contacting surfaces with a shop towel.

    GHH124054Courtesy of HONDA, U.S.A., INC.
    7. Apply liquid gasket (P/N 08718-0004 or 08718-0009) to the chain case contact areas (A). Install the component within 5 minutes of applying the liquid gasket.
    NOTE:
    • Apply a 3.0 mm (0.118 in) diameter bead of liquid gasket to the chain case contact areas.
    • If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket.
    GHH124055Courtesy of HONDA, U.S.A., INC.
    8. Place the cylinder head cover (A) on the cylinder head.

    9. Slide the cover slightly back and forth to seat the head cover gasket.

    NOTE:
    • Wait at least 30 minutes before filing the engine with oil.
    • Do not run the engine for at least 3 hours after installing the head cover.

    10. Inspect the cover washer (B). Replace any washer that is damaged or deteriorated.

    GHH124056Courtesy of HONDA, U.S.A., INC.
    11. Torque the bolts in three steps. In the final step, torque all bolts, in sequence, to 10 N•m (1.0 kgf•m, 7 lbf•ft).
  6. Cylinder Head Cover Peripheral Assembly 
    GHH124057Courtesy of HONDA, U.S.A., INC.
    1. Connect the breather hose (A).

    2. Install the harness holder (B).

  7. Ignition Coil 
    GHH124058Courtesy of HONDA, U.S.A., INC.
    1. Install the ignition coils.

    2. Connect the connectors.

  8. Intake Manifold/Chamber Assembly 
    GHH124059Courtesy of HONDA, U.S.A., INC.
    1. Connect the PCV hose (A).

    2. Install the intake manifold/chamber assembly (B).

  9. Intake Manifold/Chamber Peripheral Assembly 
    GHH124060Courtesy of HONDA, U.S.A., INC.
    1. Install the engine wire harness (A).

    2. Connect the connectors (B).

  10. Intake Manifold Bracket 
    GHH124061Courtesy of HONDA, U.S.A., INC.
    1. Install the intake manifold bracket mounting bolts.
  11. Engine Undercover 
    GHH124062Courtesy of HONDA, U.S.A., INC.
    1. Install the engine undercover (A).
  12. Throttle Body - Move 
    GHH124063Courtesy of HONDA, U.S.A., INC.
    1. Install the throttle body (A) with new gasket (B).
  13. Intake Air Pipe 
    GHH124064Courtesy of HONDA, U.S.A., INC.
    1. Install the intake air pipe.
  14. Intake Air Duct 
    GHH124065Courtesy of HONDA, U.S.A., INC.
    1. Install the intake air duct.
  15. Intake Air Resonator 
    GHH124066Courtesy of HONDA, U.S.A., INC.
    1. Install the intake air resonator.
  16. Air Cleaner 
    GHH124067Courtesy of HONDA, U.S.A., INC.
    1. Install the air cleaner (A).

    2. Connect the intake air duct (B) to the air cleaner.

  17. Engine Cover 
    GHH124068Courtesy of HONDA, U.S.A., INC.
    1. Install the engine cover.