DTC 2607: XM Diag
- Check the vehicle battery condition first (see BATTERY TEST ).
- Before you troubleshoot, make sure to follow the GENERAL TROUBLESHOOTING INFORMATION .
- Clear the hard ERROR CODE .
- Turn the ignition switch to LOCK (0), and then back ON (II).
- Go into the SYSTEM DIAGNOSTIC MODE , and select the Self-Diagnosis Mode in the Select Diagnosis Items menu .
- Check the System Links screen.
Is the XM icon red?
YES -Go to step 5.
NO -Intermittent failure, the system is OK at this time. If the vehicle repeatedly comes back with the DTC, replace the AUDIO-NAVIGATION UNIT . ■
- Turn the ignition switch to LOCK (0).
- Check for poor connections or loose terminals at audio-navigation unit connector D (14P), connector A (14P), and XM receiver connector A (14P).
Are the connections OK?
YES -Go to step 7.
NO -Repair poor connections or loose terminals, and recheck the SELF-DIAGNOSIS MODE . ■
- Disconnect audio-navigation unit connector D (14P) and XM receiver connector A (14P).
- Connect audio-navigation unit connector D (14P) terminals No. 9 and No. 10 with a jumper wire.
- Check for continuity between XM receiver connector A (14P) terminals No. 9 and No. 10.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -Go to step 10.
NO -There is an open in the wire between audio-navigation unit and the XM receiver. Replace the affected shielded harness. ■
- Disconnect the jumper wire.
- Disconnect connector A (14P).
- Check for continuity between audio-navigation unit connector D (14P) terminals No. 9 and No. 10.Fig 3: Checking For Continuity Between Audio-Navigation Unit Connector D (14P) Terminals No. 9 And No. 10
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -There is a short in the wire(s) between GA-NET (+) and (-) wire. Replace the affected shielded harness. ■
NO -Go to step 13.
- Check for continuity between body ground and audio-navigation unit connector D (14P) terminals No. 9 and No. 10 individually.Fig 4: Checking For Continuity Between Body Ground And Audio-Navigation Unit Connector D (14P) Terminals No. 9 And No. 10 Individually
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -There is a short to body ground in the wire(s) between the audio-navigation unit, the, and the XM receiver. Replace the affected shielded harness. ■
NO -Go to step 14.
- Reconnect the all connectors, then turn the ignition switch to ON (II).
- Go into the SYSTEM DIAGNOSTIC MODE , and select the Self-Diagnosis Mode in the Select Diagnosis Items menu .
- Check the System Links.
Is the XM icon red?
YES -Go to step 17.
NO -Intermittent failure, the system is OK at this time. If the unit repeatedly comes back with the DTC, replace the AUDIO-NAVIGATION UNIT . ■
- Turn the ignition switch to LOCK (0).
- Disconnect connector A (14P), and then turn the ignition switch to ON (II).
- Go into the SYSTEM DIAGNOSTIC MODE , and Select the Self-Diagnosis Mode in the Select Diagnosis Items Menu .
- Check the System Links.
Is the XM icon red?
YES -Go to step 21.
NO -Internal short circuit in the. ■
- Turn the ignition switch to LOCK (0).
- Connect connector A (14P).
- Disconnect XM receiver connector A (14P), and then turn the ignition switch to ON (II).
- Go into the SYSTEM DIAGNOSTIC MODE , and Select the Self-Diagnosis Mode in the Select Diagnosis Items Menu .
- Check the System Links.
Is the XM icon red?
YES -Replace the AUDIO-NAVIGATION UNIT (see . ■
NO -Replace the XM receiver (see XM RECEIVER REPLACEMENT . ■