LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2009 >> Element SC, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 86 (Driveline/Axle) >> Driveshaft Installation

Driveshaft Installation

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2017 Honda Odyssey, 2016 Honda Odyssey, 2015 Honda Odyssey, 2014 Honda Odyssey, and 2013 Honda Odyssey. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Before starting installation, make sure the mating surfaces of the joint and the splined section are clean.
  1. Apply about 5 g (0.18 oz.) of moly 60 paste (P/N 08734-0001) to the contact area (A) of the outboard joint and the front wheel bearing.
    NOTE: The paste helps prevent noise and vibration.
    Fig 1: Identifying Contact Area
    G06969546Courtesy of AMERICAN HONDA MOTOR CO., INC.
  2. Clean the areas where the driveshaft contacts the differential thoroughly with solvent, and dry them with compressed air.
    NOTE: Do not wash the rubber parts with solvent.
  3. Left driveshaft: Install a new set ring (A) into the set ring groove (B) of the driveshaft inboard joint.
    Fig 2: Identifying Driveshaft Inboard Joint Ring Groove And Set Ring
    G06969547Courtesy of AMERICAN HONDA MOTOR CO., INC.
  4. Left driveshaft: Insert the inboard end (A) of the driveshaft into the differential (B) until the set ring (C) locks in the groove (D).
    NOTE: Insert the driveshaft horizontally to prevent damaging the oil seal.
    Fig 3: Inserting Inboard End Of Driveshaft Into Differential
    G06969548Courtesy of AMERICAN HONDA MOTOR CO., INC.
  5. Right driveshaft: Insert the inboard joint (A) into the differential correctly.
    NOTE:
    • Insert the driveshaft horizontally to prevent damaging the oil seal (B).
    • Be careful not to damage the inboard joint ring (C).
    • Make sure to set the "TOP" mark of the driveshaft bearing bracket (D) to upper side when you install it.
      Fig 4: Inserting Inboard Joint Into Differential
      G06969549Courtesy of AMERICAN HONDA MOTOR CO., INC.
  6. Right driveshaft: Install the driveshaft bearing bracket bolts (A).
    Fig 5: Driveshaft Bearing Bracket Bolts With Torque Specifications
    G06969550Courtesy of AMERICAN HONDA MOTOR CO., INC.
  7. Install the outboard joint (A) into the front hub (B) on the knuckle.
    Fig 6: Installing Outboard Joint Into Front Hub On Knuckle
    G06969551Courtesy of AMERICAN HONDA MOTOR CO., INC.
  8. Wipe off any grease contamination from the ball joint tapered section and threads, then install the knuckle (A) onto the lower arm (B). Be careful not to damage the ball joint boot (C). Wipe off the grease before tightening the nut at the ball joint. Torque a new castle nut (D) to the lower torque specification, then tighten it only far enough to align the slot with the ball joint pin hole.
    NOTE:
    • Make sure the ball joint boot is not damaged or cracked.
    • Do not align the nut by loosening it.
      Fig 7: Knuckle, Lower Arm And Castle Nut With Torque Specifications
      G06969552Courtesy of AMERICAN HONDA MOTOR CO., INC.
  9. Install the lock pin (E) into the ball joint pin hole as shown in the figure.
  10. With headlight leveling system: If the right side driveshaft was removed, install the front suspension stroke sensor (see SUSPENSION STROKE SENSOR REPLACEMENT ).
  11. Apply a small amount of engine oil to the seating surface of a new spindle nut (A).
    Fig 8: Spindle Nut With Torque Specifications
    G06969553Courtesy of AMERICAN HONDA MOTOR CO., INC.
  12. Install the spindle nut, then tighten it. After tightening, use a drift to stake the spindle nut shoulder (B) against the driveshaft.
  13. Clean the mating surfaces between the brake disc and the inside of the wheel, then install the front wheel.
  14. Turn the wheel by hand, and make sure there is no interference between the driveshaft and surrounding parts.
  15. Lower the vehicle.
  16. Refill the transmission with the recommended transmission fluid:
  17. Check the wheel alignment, and adjust it if necessary (see WHEEL ALIGNMENT ).
  18. With headlight leveling system: Do the headlight initial position learning procedure (see HEADLIGHT INITIAL POSITION LEARNING PROCEDURE ).
  19. Test-drive the vehicle.