LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2008 >> Pilot EX, 3.5 YF2 >> Repair and Diagnosis >> Engine Performance >> System >> PGM-FI System >> DTC Troubleshooting >> DTC U0114: F-CAN Malfunction (PCM-VTM-4 Control Unit)

DTC U0114: F-CAN Malfunction (PCM-VTM-4 Control Unit)

NOTE:
  • Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).
  • If DTC U0073 is stored at the same time as DTC U0114, troubleshoot DTC U0073 first, then recheck for DTC U0114.
  • Information marked with an asterisk (*) applies to the CANL line.
  1. Turn the ignition switch ON (II).
  2. Clear the DTC with the HDS.
  3. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC U0114 indicated? 

    YES  -Go to step 4.

    NO  -Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the VTM-4 control unit and the PCM.

  4. Check for a VTM-4 system DTCs in the DTCs MENU with the HDS.

    Is VTM-4 DTC 41 indicated? 

    YES  -Go to step 5.

    NO  -Go to step  11.

  5. Turn the ignition switch OFF.
  6. Jump the SCS line with the HDS.
  7. Disconnect PCM connector A (44P).
  8. Disconnect VTM-4 control unit connector A (22P) (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ).
  9. Connect VTM-4 control unit 22P connector terminals A11 and A22* to body ground with a jumper wire.
    Fig 1: Connecting VTM-4 Control Unit 22P Connector Terminals To Body Ground With Jumper Wire
    G05593717Courtesy of AMERICAN HONDA MOTOR CO., INC.
  10. Check for continuity between PCM connector terminal A36 and A1 * and body ground individually.
    Fig 2: Checking Continuity Between PCM Connector Terminals And Body Ground
    G05593718Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -Substitute a known-good VTM-4 control unit (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ), then go to step  20 and recheck. If DTC U0114 is not indicated, replace the original VTM-4 control unit (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ), then go to step  20.

    NO  -Repair open in the wire between the VTM-4 control unit (A11 (A22)*) and the PCM (A36 (A1)*), then go to step  20.

  11. Check for poor connections at the VTM-4 control unit connectors A (20P) and B (12P).

    Are the connections OK? 

    YES  -Go to step  9.

    NO  -Repair the connections, then go to step  20.

  12. Turn the ignition switch OFF.
  13. If not already done, disconnect VTM-4 control unit connector A (22P) (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ).
  14. Turn the ignition switch ON (II).
  15. Measure voltage between VTM-4 control unit 22P connector terminal A1 and body ground.
    Fig 3: Measuring Voltage Between VTM-4 Control Unit 22P Connector Terminal And Body Ground
    G05593719Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  -Go to step 16.

    NO  -Check the No. 11 VTM-4 (7.5 A) fuse in the driver's under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the No. 11 VTM-4 (7.5 A) fuse and the VTM-4 control unit, then go to step  19.

  16. Turn the ignition switch OFF.
  17. Disconnect VTM-4 control unit connector B (12P) (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ).
  18. Check for continuity between VTM-4 control unit 12P connector terminal B5 and body ground.
    Fig 4: Checking Continuity Between VTM-4 Control Unit 12P Connector Terminal And Body Ground
    G05593720Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    YES  -Substitute a known-good VTM-4 control unit (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ), then go to step  20 and recheck. If DTC U0114 is not indicated, replace the original VTM-4 control unit (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ), then go to step  20.

    NO  -Repair open in the wire between the VTM-4 control unit and G602, then go to step  20.

  19. Turn the ignition switch OFF.
  20. Reconnect all connectors.
  21. Turn the ignition switch ON (II).
  22. Reset the PCM with the HDS.
  23. Do the PCM idle learn procedure (see PCM IDLE LEARN PROCEDURE ).
  24. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC U0114 indicated? 

    YES  -Check for poor connections or loose terminals at the VTM-4 control unit and the PCM, then go to step  1.

    NO  -Troubleshooting is complete. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.