DTC U0114: F-CAN Malfunction (PCM-VTM-4 Control Unit)
- Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).
- If DTC U0073 is stored at the same time as DTC U0114, troubleshoot DTC U0073 first, then recheck for DTC U0114.
- Information marked with an asterisk (*) applies to the CANL line.
- Turn the ignition switch ON (II).
- Clear the DTC with the HDS.
- Check for Temporary DTCs or DTCs with the HDS.
Is DTC U0114 indicated?
YES -Go to step 4.
NO -Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the VTM-4 control unit and the PCM.
- Check for a VTM-4 system DTCs in the DTCs MENU with the HDS.
Is VTM-4 DTC 41 indicated?
YES -Go to step 5.
NO -Go to step 11.
- Turn the ignition switch OFF.
- Jump the SCS line with the HDS.
- Disconnect PCM connector A (44P).
- Disconnect VTM-4 control unit connector A (22P) (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ).
- Connect VTM-4 control unit 22P connector terminals A11 and A22* to body ground with a jumper wire.
- Check for continuity between PCM connector terminal A36 and A1 * and body ground individually.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -Substitute a known-good VTM-4 control unit (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ), then go to step 20 and recheck. If DTC U0114 is not indicated, replace the original VTM-4 control unit (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ), then go to step 20.
NO -Repair open in the wire between the VTM-4 control unit (A11 (A22)*) and the PCM (A36 (A1)*), then go to step 20.
- Check for poor connections at the VTM-4 control unit connectors A (20P) and B (12P).
Are the connections OK?
YES -Go to step 9.
NO -Repair the connections, then go to step 20.
- Turn the ignition switch OFF.
- If not already done, disconnect VTM-4 control unit connector A (22P) (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ).
- Turn the ignition switch ON (II).
- Measure voltage between VTM-4 control unit 22P connector terminal A1 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there battery voltage?
YES -Go to step 16.
NO -Check the No. 11 VTM-4 (7.5 A) fuse in the driver's under-dash fuse/relay box. If the fuse is OK, repair open in the wire between the No. 11 VTM-4 (7.5 A) fuse and the VTM-4 control unit, then go to step 19.
- Turn the ignition switch OFF.
- Disconnect VTM-4 control unit connector B (12P) (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ).
- Check for continuity between VTM-4 control unit 12P connector terminal B5 and body ground.
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Is there continuity?
YES -Substitute a known-good VTM-4 control unit (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ), then go to step 20 and recheck. If DTC U0114 is not indicated, replace the original VTM-4 control unit (see VTM-4 LOCK SWITCH TEST/REPLACEMENT ), then go to step 20.
NO -Repair open in the wire between the VTM-4 control unit and G602, then go to step 20.
- Turn the ignition switch OFF.
- Reconnect all connectors.
- Turn the ignition switch ON (II).
- Reset the PCM with the HDS.
- Do the PCM idle learn procedure (see PCM IDLE LEARN PROCEDURE ).
- Check for Temporary DTCs or DTCs with the HDS.
Is DTC U0114 indicated?
YES -Check for poor connections or loose terminals at the VTM-4 control unit and the PCM, then go to step 1.
NO -Troubleshooting is complete. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.