LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2007 >> Civic Hybrid >> Repair and Diagnosis >> Engine Performance >> System >> Electronic Throttle Control System (Hybrid) >> DTC Troubleshooting >> DTC P1659: ETCS Control Relay OFF Malfunction

DTC P1659: ETCS Control Relay OFF Malfunction

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review GENERAL TROUBLESHOOTING INFORMATION .
  1. Turn the ignition switch ON (II).
  2. Clear the DTC with the HDS.
  3. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC P1659 indicated? 

    YES  - Go to step  4.

    NO  - Intermittent failure, the system is OK at this time. Check for poor connections or loose terminals at the ETCS control relay and the PCM.

  4. Turn the ignition switch OFF.
  5. Check the No. 21 DBW (THROTTLE ACTUATOR CONTROL) (15 A) fuse in the under-hood fuse/relay box.

    Is the fuse OK? 

    YES  - Go to step  6.

    NO  - Go to step  17.

  6. Remove the ETCS control relay (F) from the under-hood fuse/relay box.
    Fig 1: Identifying ETCS Control Relay
    G05532039Courtesy of AMERICAN HONDA MOTOR CO., INC.
  7. Test the ETCS control relay (see POWER RELAY TEST ).

    Is the ETCS control relay OK ? 

    YES  - Go to step  8.

    NO  - Replace the ETCS control relay, then go to step  23.

  8. Turn the ignition switch ON (II).
  9. Measure voltage between ETCS control relay 4P connector terminal No. 4 and body ground.
    Fig 2: Measuring Voltage Between ETCS Control Relay 4P Connector Terminal No. 4 And Body Ground
    G05532040Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  - Go to step  10.

    NO  - Replace the under-hood fuse/relay box (see REMOVAL AND INSTALLATION ), then go to step  23.

  10. Measure voltage between ETCS control relay 4P connector terminal No. 1 and body ground.
    Fig 3: Measuring Voltage Between ETCS Control Relay 4P Connector Terminal No. 1 And Body Ground
    G05532041Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    YES  - Go to step  11.

    NO  - Replace the under-hood fuse/relay box (see REMOVAL AND INSTALLATION ), then go to step  22.

  11. Turn the ignition switch OFF.
  12. Jump the SCS line with the HDS.
  13. Disconnect PCM connector C (44P).
  14. Check for continuity between ETCS control relay 4P connector terminal No. 2 and PCM connector terminal C1.

    Is there continuity? 

    YES  - Go to step  15.

    NO  - Repair open in the wire between the PCM (C1) and the ETCS control relay, then go to step  23.

    Fig 4: Checking Continuity Between ETCS Control Relay 4P Connector Terminal No. 2 & PCM Connector Terminal C1
    G05532042Courtesy of AMERICAN HONDA MOTOR CO., INC.
  15. Disconnect PCM connector A (44P).
  16. Check for continuity between ETCS control relay 4P connector terminal No. 3 and PCM connector terminal A20.

    Is there continuity? 

    YES  - Go to step  28.

    NO  - Repair open in the wire between the PCM (A20) and the ETCS control relay, then go to step  23.

    Fig 5: Checking Continuity Between ETCS Control Relay 4P Connector Terminal No. 3 & Terminal A20
    G05532043Courtesy of AMERICAN HONDA MOTOR CO., INC.
  17. Remove the ETCS control relay (F) from the under-hood fuse/relay box.
    Fig 6: Identifying ETCS Control Relay
    G05532044Courtesy of AMERICAN HONDA MOTOR CO., INC.
  18. Jump the SCS line with the HDS.
  19. Disconnect PCM connector C (44P).
  20. Check for continuity between PCM connector terminal C1 and body ground.

    Is there continuity? 

    YES  - Repair short in the wire between the PCM (C1) and the ETCS control relay, then go to step  23.

    NO  - Go to step  21.

    Fig 7: Checking Continuity Between PCM Connector Terminal C1 & Body Ground
    G05532045Courtesy of AMERICAN HONDA MOTOR CO., INC.
  21. Check for continuity between ETCS control relay 4P connector terminal No. 1 and body ground.

    Is there continuity? 

    YES  - Replace the under-hood fuse/relay box (see REMOVAL AND INSTALLATION ), then go to step  23.

    NO  - Go to step  28.

    Fig 8: Checking Continuity Between ETCS Control Relay 4P Connector Terminal No. 1 & Body Ground
    G05532046Courtesy of AMERICAN HONDA MOTOR CO., INC.
  22. Turn the ignition switch OFF.
  23. Reconnect all connectors.
  24. Turn the ignition switch ON (II).
  25. Reset the PCM with the HDS.
  26. Do PCM IDLE LEARN PROCEDURE .
  27. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC P1659 indicated? 

    YES  - Check for poor connections or loose terminals at the ETCS control relay and the PCM, then go to step  1.

    NO  - Troubleshooting is complete. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC'S TROUBLESHOOTING .

  28. Reconnect all connectors.
  29. Update the PCM if it does not have the latest software (see PCM UPDATE ), or substitute a known-good PCM (see SUBSTITUTING THE PCM ).
  30. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC P1659 indicated? 

    YES  - Check for poor connections or loose terminals at the ETCS control relay and the PCM. If the PCM was updated, substitute a known-good PCM (see SUBSTITUTING THE PCM ), then recheck. If the PCM was substituted, go to step  1.

    NO  - If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM (see PCM REPLACEMENT ). If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC'S TROUBLESHOOTING .