LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2007 >> Accord Base, Standard, APG6 >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> Engine Mount Control System (Except Hybrid) >> Troubleshooting

Engine Mount Control System (Except Hybrid): Troubleshooting

Special Tools Required 

Vacuum pump/gauge, 0---30 in.Hg

Snap-on YA4000A or equivalent, commercially available

NOTE: Check the vacuum hoses and lines for damage and proper connections before troubleshooting.

Follow this procedure if the engine vibrates excessively when idling.

A/T 

  1. Start the engine, and let it idle (see IDLE SPEED INSPECTION ).
  2. Raise the engine speed from idling to 2,000 rpm.
  3. Check the MOUNT CTRL SOL in the PGM-FI DATA LIST with the Honda Diagnostic System (HDS).

    Is ON indicated at idling and OFF indicated at 2,000 rpm? 

    1. YES -  Go to step 4.
    2. NO -  Update the powertrain control module (PCM) if it does not have the latest software (see UPDATING THE ECM/PCM ), or substitute a known-good PCM (see SUBSTITUTE THE ECM/PCM ), then recheck. If the engine mount control system works properly, and the PCM was updated, the troubleshooting is complete. If the PCM was substituted, replace the original PCM (see ECM/PCM REPLACEMENT ).
  4. Turn the ignition switch OFF.
  5. Disconnect the engine mount control solenoid valve 2P connector from the engine mount control solenoid valve.
  6. Turn the ignition switch ON (II).
  7. Measure the voltage between engine mount control solenoid valve 2P connector terminal No.2 and body ground.
  8. Fig 1: Measuring Voltage Between Engine Mount Control Solenoid Valve 2P Connector Terminal And Body Ground
    G03645955Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    1. YES -  Go to step 8.
    2. NO -  Repair an open in the wire between the engine mount control solenoid valve 2P connector terminal No. 2 and No. 18 (15A) fuse in the under-dash fuse/relay box.

  9. Measure voltage between engine mount control solenoid valve 2P connector terminals No. 1 and No. 2.
    Fig 2: Measuring Voltage Between Engine Mount Control Solenoid Valve 2P Connector Terminals
    G03645956Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    1. YES -  Go to step 9.
    2. NO -  Repair an open in the wire between PCM (B15) and the engine mount control solenoid valve 2P connector. If the wire is OK, update the PCM if it does not have the latest software (see UPDATING THE ECM/PCM ), or substitute a known-good PCM (see SUBSTITUTE THE ECM/PCM ), and recheck. If the engine mount control system works properly, and the PCM was updated, the troubleshooting is complete. If the PCM was substituted, replace the original PCM (see ECM/PCM REPLACEMENT ).
  10. Raise the engine speed above 1,000 rpm.
  11. Measure the voltage between engine mount control solenoid valve 2P connector terminals No. 1 and No. 2.
    Fig 3: Measuring Voltage Between Engine Mount Control Solenoid Valve 2P Connector Terminals
    G03645957Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    1. YES -  Repair a short to body ground in the wire between PCM (B15) and the engine mount control solenoid valve. If the wire is OK, update the PCM if it does not have the latest software (see UPDATING THE ECM/PCM ), or substitute a known-good PCM (see SUBSTITUTE THE ECM/PCM ), and recheck. If the engine mount control system works properly, and the PCM was updated, the troubleshooting is complete. If the PCM was substituted, replace the original PCM (see ECM/PCM REPLACEMENT ).
    2. NO -  Go to step 11.
  12. Disconnect the upper vacuum hose (A) from the engine mount control solenoid valve (B), and connect a vacuum pump/gauge, 0-30 in. Hg, to the hose. Apply about 20 in.Hg of vacuum, and wait 20 seconds.
    Fig 4: Disconnecting The Upper Vacuum Hose From The Engine Mount Control Solenoid Valve
    G03645958Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Does the engine mount hold vacuum? 

    1. YES -  Go to step 12.
    2. NO -  Either the vacuum hose or the engine mount has a vacuum leak. Repair as needed.
  13. Release the vacuum, then apply vacuum again.

    Is there a noticeable change in idle smoothness with and without vacuum applied? 

    1. YES -  Go to step 13.
    2. NO -  Replace the front engine mount.
  14. Connect a vacuum pump/gauge, 0-30 in. Hg, to the engine mount control solenoid valve (A).
  15. Fig 5: Connecting Vacuum Pump/Gauge, 0---30 in. Hg, To The Engine Mount Control Solenoid Valve
    G03645959Courtesy of AMERICAN HONDA MOTOR CO., INC.

Is there manifold vacuum at idle, and a decrease in manifold vacuum when you raise the engine speed above 1,000 rpm? 

  1. YES -  The system is OK.
  2. NO -  Replace the engine mount control solenoid valve.