DTC P0401: EGR Insufficient Flow
- Turn the ignition switch ON (II).
- Clear the DTC with the HDS.
- Start the engine. Hold the engine speed at 3,000 RPM without load (in Park or neutral) until the radiator fan comes on, then let it idle.
- Do the EGR TEST in the INSPECTION MENU with the HDS.
Is the result OK?
- YES - Go to step 5.
- NO - Go to step 7.
- Test-drive under these conditions:
- Engine coolant temperature above 158 °F (70 °C)
- Transmission in D position
- Vehicle speed at 25 mph (40 km/h) or more, and engine speed between 1,100 RPM and 3,000 RPM
- During the drive, decelerate (with the throttle fully closed) for 5 seconds
- Monitor the OBD STATUS for DTC P0401 in the DTCs MENU with the HDS.
Does the screen indicate FAILED?
- YES - Remove the intake manifold cover, clean the intake manifold, and EGR ports with throttle plate and induction cleaner, then go to step 9.
- NO - If the screen indicates PASSED, intermittent failure, system is OK at this time. If the screen indicates EXECUTING, keep driving until a result comes on. If the screen indicates OUT OF CONDITION, go to step 5 and recheck.
- Turn the ignition switch OFF.
- Replace the EGR valve (see EGR VALVE REPLACEMENT ).
- Turn the ignition switch ON (II).
- Reset the PCM with the HDS.
- Do the PCM idle learn procedure (see PCM IDLE LEARN PROCEDURE ).
- Test-drive under these conditions:
- Engine coolant temperature above 158 °F (70 °C)
- Transmission in D position
- Vehicle speed at 25 mph (40 km/h) or more, and engine speed between 1,100 RPM and 3,000 RPM
- During the drive, decelerate (with the throttle fully closed) for 5 seconds
- Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0401 indicated?
- Monitor the OBD STATUS for DTC P0401 in the DTCs MENU with the HDS.
Does the screen indicate PASSED?
- YES - Troubleshooting is complete. If any other Temporary DTCs or DTCs are indicated in step 13, go to the indicated DTC's troubleshooting
- NO - If the screen indicates FAILED, check for poor connections or loose terminals at the EGR valve and the PCM, then go to step 1. If the screen indicates EXECUTING, keep driving until a result comes on. If the screen indicates OUT OF CONDITION, go to step 12.
- Update the PCM if it does not have the latest software, or substitute a known-good PCM (see PCM UPDATING AND SUBSTITUTION FOR TESTING ).
- Test-drive under these conditions:
- Engine coolant temperature above 158 °F (70 °C)
- Transmission in D position
- Vehicle speed at 25 mph (40 km/h) or more, and engine speed between 1,100 RPM and 3,000 RPM
- During the drive, decelerate (with the throttle fully closed) for 5 seconds
- Check for Temporary DTCs or DTCs with the HDS.
Is DTC P0401 indicated?
- YES - Check for poor connections or loose terminals at the EGR valve and the PCM. If the PCM was updated, substitute a known-good PCM (see SUBSTITUTING THE PCM ), then go to step 16. If the PCM was substituted, go to step 1.
- NO - Go to step 18.
- Monitor the OBD STATUS for DTC P0401 in the DTCs MENU with the HDS.
Does the screen indicated PASSED?
- YES - If the PCM was updated, troubleshooting is complete. If the PCM was substituted, replace the original PCM (see PCM REPLACEMENT ). If any other Temporary DTCs or DTCs are indicated in step 17, go to the indicated DTC's troubleshooting
- NO - If the screen indicates FAILED, check for poor connections or loose terminals at the EGR valve and the PCM. If the PCM was updated, substitute a known-good PCM (see SUBSTITUTING THE PCM ), then go to step 16 if the PCM was substituted, go to step 1. If the screen indicates NOT COMPLETED, go to step 16.