LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2003 >> Element DX, 2.4 YH1, Standard >> Repair and Diagnosis >> Steering >> Manual Steering >> Power Steering >> Steering Gearbox Overhaul >> Exploded View >> Removal

Exploded View: Removal

  1. Remove the steering gearbox (see STEERING GEARBOX REMOVAL ).

    Disassembly 

  2. Remove cylinder lines (A) and return line joint (B) from the gearbox.
    Fig 1: Identifying Cylinder Lines And Return Line Joint
    G03678966Courtesy of AMERICAN HONDA MOTOR CO., INC.
  3. Drain the fluid from the cylinder fittings by slowly moving the steering rack back and forth.
  4. Unbend the lock washers (A).
    Fig 2: Unbending Lock Washers
    G03678967Courtesy of AMERICAN HONDA MOTOR CO., INC.
  5. Hold the bracket (A) with one wrench, and unscrew both tie-rods (B) with another wrench. Remove the lock washers.
    Fig 3: Removing Lock Washers
    G03678968Courtesy of AMERICAN HONDA MOTOR CO., INC.
  6. Remove the stop washer (A), the 12 mm flange bolts (B), O-rings (C), and bracket (D) from the steering gearbox.
    Fig 4: Removing Stop Washer, 12 Mm Flange Bolts, O-Rings And Bracket From Steering Gearbox
    G03678969Courtesy of AMERICAN HONDA MOTOR CO., INC.
  7. Remove the boot guard (A) by removing the 8 mm flange bolt (C) on the rack end.
    Fig 5: Removing Boot Guard
    G03678970Courtesy of AMERICAN HONDA MOTOR CO., INC.
  8. Remove the boot band (D) and clip (E). Pull the boot B away from the end of the steering gearbox. Remove the rack end plug (F).
  9. Loosen the locknut (A), then remove the rack guide screw (B), spring (C), and rack guide (D) from the steering gearbox.
    Fig 6: Removing Rack Guide Screw, Spring And Rack Guide From Steering Gearbox
    G03678971Courtesy of AMERICAN HONDA MOTOR CO., INC.
  10. Remove the internal snap ring (A) and backup ring (B) from the cylinder housing.
    Fig 7: Removing Internal Snap Ring And Backup Ring From Cylinder Housing
    G03678972Courtesy of AMERICAN HONDA MOTOR CO., INC.
  11. Remove the valve body unit (A) from the steering gearbox. Remove the O-ring (B) and discard it.
    Fig 8: Removing Valve Body Unit From Steering Gearbox
    G03678973Courtesy of AMERICAN HONDA MOTOR CO., INC.
  12. Remove the two boot bands (B) from boot A. Compress boot A by hand, and apply vinyl tape (C) so the boots stay collapsed and pulled back.
    Fig 9: Removing Two Boot Bands From Boot
    G03678974Courtesy of AMERICAN HONDA MOTOR CO., INC.
  13. Hold the gearbox housing using a C-clamp (commercially available) (A) and the wooden blocks (B) as shown. Do not clamp the cylinder part of the housing or gearbox housing in the vise.
    Fig 10: Holding Gearbox Housing Using C-Clamp And Wooden Blocks
    G03678975Courtesy of AMERICAN HONDA MOTOR CO., INC.
  14. Install the special tool (A) on the lock screw (B), then loosen and remove the lock screw from inside of the gearbox housing (C).
    Fig 11: Removing Lock Screw Using Special Tool
    G03678976Courtesy of AMERICAN HONDA MOTOR CO., INC.
  15. Remove the special tool.
  16. Pull on the cylinder to remove it from the gearbox housing. Remove boot A and the slider guide (B) from the cylinder.
    Fig 12: Removing Boot And Slider Guide From Cylinder
    G03678977Courtesy of AMERICAN HONDA MOTOR CO., INC.
  17. Check the slider guide for damage and cracks. Use vernier calipers to measure the thickness of the slider guide. If the thickness is less than the service limit (A), replace the slider guide.
    Fig 13: Identifying Thickness Of Slider Guide
    G03678978Courtesy of AMERICAN HONDA MOTOR CO., INC.
  18. Remove and discard the stop ring (A) on the cylinder by expanding it with snap ring pliers. Remove and discard the lock screw (B).
    Fig 14: Removing Stop Ring And Lock Screw
    G03678979Courtesy of AMERICAN HONDA MOTOR CO., INC.
  19. Set the cylinder housing (A) in a press so the cylinder side points downward, then press the cylinder end seal (B) and steering rack (C) out of the cylinder. Hold the rack to keep it from falling when pressed clear.
    Fig 15: Pressing Cylinder End Seal And Steering Rack Out Of Cylinder
    G03678980Courtesy of AMERICAN HONDA MOTOR CO., INC.
  20. Remove the cylinder end seal from the steering rack.
  21. Insert the special tools into the cylinder.

    Make sure the attachment (A) of the special tools is securely positioned on the bushing edges (B).

    Fig 16: Inserting Special Tools Into Cylinder
    G03678981Courtesy of AMERICAN HONDA MOTOR CO., INC.
  22. Place the cylinder in a press, then remove the cylinder end seal (C), backup ring (D), and bushing from the cylinder by pressing on the special tool end.

    Note the items when pressing the cylinder end seal:

    • Keep tool straight to avoid damaging the cylinder wall. Check the tool angle, and correct it if necessary, when removing the cylinder end seal.
    • Use a press to remove the cylinder end seal. Do not try to remove the seal by striking the tool; striking the tool would break the cylinder end seal, and the seal would remain in the cylinder.
  23. Carefully pry the piston seal ring (A) and O-ring (B) off the rack piston. Be careful not to damage the inside of the seal ring groove and piston edges when removing the seal ring.
    Fig 17: Prying Piston Seal Ring And O-Ring Off Rack Piston
    G03678982Courtesy of AMERICAN HONDA MOTOR CO., INC.
  24. Before removing the valve housing (A), apply vinyl tape (B) to the splines on the pinion shaft.
    Fig 18: Removing Valve Housing
    G03678983Courtesy of AMERICAN HONDA MOTOR CO., INC.
  25. Separate the valve housing from the pinion shaft/valve using a press.
  26. With your finger, check the inner wall of the valve housing where the seal ring slides. If there is a step in the wall, the housing is worn. Replace it.
    NOTE: There may be sliding marks from the seal ring on the wall of the valve housing. Replace the valve housing only if the wall is stepped.
    Fig 19: Checking Inner Wall Of Valve Housing
    G03678984Courtesy of AMERICAN HONDA MOTOR CO., INC.
  27. Check for wear, burrs, and other damage to the edges of the grooves in the sleeve.
    NOTE: The pinion shaft and sleeve are a precision matched set. If either the pinion shaft or sleeve must be replaced, replace both parts as a set.
    Fig 20: Identifying Sleeve Edges Of Grooves
    G03678985Courtesy of AMERICAN HONDA MOTOR CO., INC.
  28. Remove the external snap ring (A) and sleeve (B) from the pinion shaft.
    Fig 21: Removing External Snap Ring And Sleeve From Pinion Shaft
    G03678986Courtesy of AMERICAN HONDA MOTOR CO., INC.
  29. Using a cutter or an equivalent tool, cut and remove the 4 seal rings from the sleeve. Be careful not to damage the edges of the sleeve grooves and the outer surface when removing the seal rings.
    Fig 22: Removing 4 Seal Rings From Sleeve
    G03678987Courtesy of AMERICAN HONDA MOTOR CO., INC.
  30. Using a cutter or an equivalent tool, cut the valve seal ring (A) and O-ring (B) at the groove (C) in the pinion shaft. Remove the valve seal ring and O-ring. Be careful not to damage the edges of the pinion shaft groove and outer surface when removing the valve seal ring and O-ring.
    Fig 23: Removing Valve Seal And O-Ring
    G03678988Courtesy of AMERICAN HONDA MOTOR CO., INC.
  31. Remove the valve oil seal (A) and wave washer (B) from the pinion shaft.

    Note these items during disassembly:

    • Inspect the ball bearing (C) by rotating the outer race slowly. If there is any excessive play or wear, replace the pinion shaft and sleeve as an assembly.
    • The pinion shaft and sleeve are a precise fit; do not intermix old and new pinion shafts and sleeves.
    Fig 24: Removing Valve Oil Seal And Wave Washer From Pinion Shaft
    G03678989Courtesy of AMERICAN HONDA MOTOR CO., INC.
  32. Press the valve oil seal (A) and roller bearing (B) out of the valve housing using a hydraulic press and special tool.
    Fig 25: Pressing Valve Oil Seal And Roller Bearing Using Hydraulic Press And Special Tool
    G03678990Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Reassembly 

  33. Apply vinyl tape (A) to the stepped portion of the pinion shaft, and coat the surface of the vinyl tape with the power steering fluid.
    Fig 26: Installing Valve Oil Seal And Wave Washer
    G03678991Courtesy of AMERICAN HONDA MOTOR CO., INC.
  34. Install the wave washer (B). Coat the inside surface of the new valve oil seal (C) with power steering fluid, and install the seal with its grooved side facing opposite the bearing, then slide it over the pinion shaft, being careful not to damage its sealing lip (D). Remove the vinyl tape.
  35. Install the special tool over the pinion, and coat the surface of the tool with power steering fluid. Slip the new O-ring (A) and new valve seal ring (B) over the special tool, and expand them.
    Fig 27: Installing Special Tool Over Pinion
    G03678992Courtesy of AMERICAN HONDA MOTOR CO., INC.
  36. Fit the O-ring in the groove of the pinion shaft. Then slide the valve seal ring over the shaft and in the groove on the pinion shaft.
  37. Remove the special tool, and apply power steering fluid to the surface of the valve seal ring (A).
    Fig 28: Applying Power Steering Fluid To Surface Of Valve Seal Ring
    G03678993Courtesy of AMERICAN HONDA MOTOR CO., INC.
  38. Apply power steering fluid to the inside of the special tool. Set the larger diameter end of the special tool over the valve seal ring, and move the special tool up and down several times to make the valve seal ring fit in the pinion shaft groove.
  39. Remove the special tool, turn it over, and slide the smaller diameter end over the valve seal ring. Move it up and down several times to make sure the valve seal ring fits snugly in the pinion shaft groove.
  40. Apply power steering fluid to the surface of the special tool. Slip two new seal rings (A) over the special tool from the smaller diameter end, and expand them. Install only two rings at a time from each end of the pinion shaft sleeve (B).

    Note these items when installing the seal rings:

    • Do not over-expand the seal rings. Install the resin seal rings with care so as not to damage them. After installation, be sure to contract the seal rings using the special tool (sizing tool).
    • There are two types of sleeve seal rings; black and brown. Do not mix the different types of rings as they are not compatible.
    Fig 29: Installing Seal Rings
    G03678994Courtesy of AMERICAN HONDA MOTOR CO., INC.
  41. Align the special tool with each groove in the sleeve, and slide a sleeve seal ring into each groove. After installation, compress the seal rings with your fingers temporarily.
  42. Apply power steering fluid to the seal rings on the sleeve, and to the entire inside surface of the special tool, then slowly insert the sleeve into the special tool.
    Fig 30: Inserting Sleeve Into Special Tool
    G03678995Courtesy of AMERICAN HONDA MOTOR CO., INC.
  43. Move the sleeve back and forth several times to make the seal rings fit snugly in the sleeve. Make sure the seal rings are not twisted.
  44. Apply power steering fluid to the surface of the pinion shaft (A). Slide the sleeve (B) onto the pinion shaft by aligning the locating pin (C) on the inside of the sleeve with the cutout (D) in the shaft. Then install the new external snap ring (E) securely in the pinion shaft groove. Be careful not to damage the valve seal ring when inserting the sleeve.
    Fig 31: Installing Pinion Shaft Components
    G03678996Courtesy of AMERICAN HONDA MOTOR CO., INC.
  45. Apply power steering fluid to the seal ring lip of the new valve oil seal (A), then install the seal in the valve housing (B) using a hydraulic press and special tools. Install the seal with its grooved side facing the tool.
    Fig 32: Installing New Valve Oil Seal
    G03678997Courtesy of AMERICAN HONDA MOTOR CO., INC.
  46. Press the roller bearing (C) into the valve housing with a hydraulic press and special tools.
  47. Apply vinyl tape (A) to the pinion shaft, then coat the vinyl tape with power steering fluid.
    Fig 33: Inserting Pinion Shaft Into Valve Housing
    G03678998Courtesy of AMERICAN HONDA MOTOR CO., INC.
  48. Insert the pinion shaft into the valve housing (B). Be careful not to damage the valve seal rings (C) and valve oil seal sealing lip (D).
  49. Remove the vinyl tape from the pinion shaft, then remove any residue from the tape adhesive.
  50. Press the pinion shaft/sleeve into the valve housing with a hydraulic press. Check that the pinion shaft/sleeve turns smoothly by hand after installing it.
    Fig 34: Pressing Pinion Shaft/Sleeve Into Valve Housing Using Hydraulic Press
    G03678999Courtesy of AMERICAN HONDA MOTOR CO., INC.
  51. Coat the special tool with power steering fluid, then slide it onto the rack, big end first.
  52. Position the new O-ring (A) and new piston seal ring (B) on the special tool, then slide them down toward the big end of the tool.

    Note these items during reassembly:

    • Do not over expand the resin seal ring. Install the resin seal ring with care so as not to damage it. After installation, be sure to contract the seal ring using the special tool (sizing tool).
    • Replace piston's O-ring and seal ring as a set.
    Fig 35: Positioning New O-Ring And New Piston Seal Ring On Special Tool
    G03679000Courtesy of AMERICAN HONDA MOTOR CO., INC.
  53. Pull the O-ring off into the piston groove, then pull the piston seal ring off into the piston groove on top of the O-ring.
  54. Coat the piston seal ring (A) and the inside of the special tool with power steering fluid, then carefully slide the tool onto the rack and over the piston seal ring.
    Fig 36: Sliding Tool Onto Rack And Over Piston Seal Ring
    G03679001Courtesy of AMERICAN HONDA MOTOR CO., INC.
  55. Move the special tool back and forth several times to make the piston seal ring fits snugly in the piston.
  56. Set the new bushing (A) on the special tool, and insert the special tools into the cylinder housing (B).
    Fig 37: Inserting Special Tools Into Cylinder Housing
    G03679002Courtesy of AMERICAN HONDA MOTOR CO., INC.
  57. Set the cylinder in a press, and install the bushing into the bottom of the cylinder by pressing on the tool with a press. Do not push on the tool with excessive force as it may damage the new bushing.
  58. Coat the sliding surface of the special tool (A) and new cylinder end seal (B) with power steering fluid. Place the seal on the special tool with its grooved side (C) facing opposite the special tool.
    Fig 38: Placing Cylinder End Seal On Special Tool With Its Grooved Side
    G03679003Courtesy of AMERICAN HONDA MOTOR CO., INC.
  59. Apply a thin coat of power steering grease to the inside of the special tool.
  60. Install the cylinder end seal (A) onto the steering rack (B) with its grooved side (C) toward the piston (D). Make sure the gap in the special tool is opposite of rack teeth.
    Fig 39: Installing Cylinder End Seal Onto Steering Rack With Its Grooved Side
    G03679004Courtesy of AMERICAN HONDA MOTOR CO., INC.
  61. Separate the cylinder end seal from the special tool, then remove the special tool.
    Fig 40: Removing Special Tool
    G03679005Courtesy of AMERICAN HONDA MOTOR CO., INC.
  62. Install the new backup ring (A) on the steering rack, then place the backup ring and cylinder end seal (B) against the piston (C).
    Fig 41: Installing New Backup Ring On Steering Rack
    G03679006Courtesy of AMERICAN HONDA MOTOR CO., INC.
  63. Mark (A) a position on the steering rack surface with a felt-tip marker, 7.7 mm (0.3 in.) from the rack end.
    Fig 42: Identifying Steering Rack Surface Marking Position From Rack End
    G03679007Courtesy of AMERICAN HONDA MOTOR CO., INC.
  64. Apply power steering grease to the steering rack teeth, then insert the steering rack (A) into the cylinder (B). Be careful not to damage the inner surface of the cylinder wall and bushing with the rack edges.
    Fig 43: Inserting Steering Rack Into Cylinder
    G03679008Courtesy of AMERICAN HONDA MOTOR CO., INC.
  65. Set the cylinder (A) in a press, then press the cylinder end seal (B) into the bottom of the cylinder until the mark (C) on the rack meets the edges (D) of the cylinder.
    Fig 44: Pressing Cylinder End Seal Into Bottom Of Cylinder
    G03679009Courtesy of AMERICAN HONDA MOTOR CO., INC.
  66. Coat the inside and outside surfaces of the new cylinder end seal (A) with power steering fluid.
    Fig 45: Installing Cylinder End Seal Onto Steering Rack
    G03679010Courtesy of AMERICAN HONDA MOTOR CO., INC.
  67. Install the cylinder end seal onto the steering rack (B) with its grooved side (C) toward the piston. Push in the cylinder end seal with your finger.
  68. Place the backup ring (D) on the cylinder end seal with its flat side facing upward. Then drive the backup ring in with the appropriate size socket wrench until the its surface is below the internal snap ring groove (E). Install the snap ring (F) in the groove.
  69. Install the new lock screw (A) on the cylinder.
    Fig 46: Installing New Lock Screw On Cylinder
    G03679011Courtesy of AMERICAN HONDA MOTOR CO., INC.
  70. Install the new stop ring (B) in the groove (C) on the cylinder by expanding it with snap ring pliers. Be careful not to scratch or damage the cylinder surface with the stop ring edges.
  71. Coat the housing surface with multipurpose grease as shown.
    Fig 47: Coating Housing Surface With Multipurpose Grease
    G03679012Courtesy of AMERICAN HONDA MOTOR CO., INC.
  72. Set the new boot bands (B) on the band installation grooves of boot A by aligning the tabs (C) with the holes (D) of the band. Do not close the ear portion of the boot band yet.
    Fig 48: Installing New Boot Bands
    G03679013Courtesy of AMERICAN HONDA MOTOR CO., INC.
  73. Compress boot A by hand, and apply vinyl tape (E) to the bellows so the boots stay collapsed and pulled back. Slide boot A over the cylinder so the smaller diameter end of the boot faces the gearbox housing.
  74. Apply power steering grease to the sliding surface of the slider guide (A). Keep grease off of the rack-to-slider guide matching surfaces and the boot-to-slider guide matching surfaces. Slide the steering rack all the way to left, and place the slider guide on the steering rack by aligning the bolt holes (B).
    Fig 49: Placing Slider Guide On Steering Rack By Aligning Bolt Holes
    G03679014Courtesy of AMERICAN HONDA MOTOR CO., INC.
  75. Hold the gearbox housing using a C-clamp (commercially available) (A) and the wooden block (B) as shown. Do not clamp the cylinder or gearbox housing in the vice.
    Fig 50: Holding Gearbox Housing Using C-Clamp And Wooden Block
    G03679015Courtesy of AMERICAN HONDA MOTOR CO., INC.
  76. Push the cylinder (A) into the gearbox housing (B) so the notch (C) is aligned with the pin (D) inside of the gearbox housing.
    Fig 51: Pushing Cylinder Into Gearbox Housing
    G03679016Courtesy of AMERICAN HONDA MOTOR CO., INC.
  77. Tighten the lock screw (A) by hand first, then install the special tool (B) on the lock screw. Lightly tighten the lock screw. Do not tighten the lock screw to the specified torque yet.
    Fig 52: Installing Special Tool On Lock Screw
    G03679017Courtesy of AMERICAN HONDA MOTOR CO., INC.
  78. Remove the special tool.
  79. Coat the new O-ring (A) with power steering grease, and carefully fit it on the valve housing.
    Fig 53: Installing Valve Body Unit And Torque Specifications
    G03679018Courtesy of AMERICAN HONDA MOTOR CO., INC.
  80. Apply power steering grease to the needle bearing (B) in the gearbox housing, then install the valve body unit (C) by engaging the gears. Note the valve body unit installation position (direction of the line connections). Tighten the flange bolts (D) to the specified torque.
  81. Apply power steering grease to the sliding surface and circumference of the rack guide (A), and install it into the gearbox housing. Wipe the grease off the threaded section of the housing.
    Fig 54: Applying Power Steering Grease And Installing Rack Guide, Spring And Rack Guide Screw To Gear Box Housing
    G03679019Courtesy of AMERICAN HONDA MOTOR CO., INC.
  82. Install the spring (B), and rack guide screw (C), then install and tighten it to 25 N.m (2.5 kgf.m, 18 lbf.ft). Loosely install the locknut (D).
  83. Center the steering rack within its stroke, and align the slider guide (B) with the holes (C) in the boot A. Fit the slider guide to boot A by pressing around the edges of the holes securely.
    Fig 55: Installing Bracket
    G03679020Courtesy of AMERICAN HONDA MOTOR CO., INC.
  84. Before installing the bracket (D), clean the mating surface of the 12 mm flange bolts (E) and bracket. Coat the new O-rings (F) with power steering grease, and install them on the 12 mm flange bolts.
  85. Loosely install the bracket on the steering rack by tightening the 12 mm flange bolts to 25 N.m (2.5 kgf.m, 18 lbf.ft).
  86. Hold the gearbox housing using a C-clamp, then install the special tool on the lock screw (A). Retighten the lock screw to the specified torque values. Remove the special tool.
    Fig 56: Installing Special Tool On Lock Screw And Torque Specifications
    G03679021Courtesy of AMERICAN HONDA MOTOR CO., INC.
  87. Retighten the 12 mm flange bolts (A) to the specified torque values.
    Fig 57: Flange Bolts Fastener Tightening Torque Specifications Table
    G03679022Courtesy of AMERICAN HONDA MOTOR CO., INC.
  88. After tightening the 12 mm flange bolts, install a new stop washer (B) over one of the bolt heads (C). Be sure the tabs (D) of the stop washer are aligned with the flat surfaces (E) of the bolt head.
  89. Clean off any grease or contamination from the boot installation grooves around the housing.
  90. Expand boot A by removing the vinyl tape, and fit the boot ends (B) in the installation grooves on the cylinder housing.
    Fig 58: Identifying Boot And Boot Ends
    G03679023Courtesy of AMERICAN HONDA MOTOR CO., INC.
  91. Close the ear portion (A) of the bands (B) with a commercially available pincers, Oetiker 1098 or equivalent (C).
    Fig 59: Closing Ear Portion Of Bands Using Commercially Available Pincers Or Oetiker 1098
    G03679024Courtesy of AMERICAN HONDA MOTOR CO., INC.
  92. Install the rack end plug (A). Clean off any grease or contamination from the boot installation grooves (C) around the housing and the rack end plug.
    Fig 60: Installing Rack End Plug And Torque Specifications
    G03679025Courtesy of AMERICAN HONDA MOTOR CO., INC.
  93. Slide the steering rack, and adjust the distance between the cylinder housing end and the end of the rack end plug to 70.5 mm (2.8 in.). Install the boot B, and set the boot end in the installation grooves in the cylinder housing and the rack end plug properly. Install the clip (D) and boot guard (E). Install the new boot band (F) in the band grooves of boot B by aligning the tabs (G) with the holes (H) in the band.
  94. Close the ear portion (A) of the band (B) with a commercially available pincers, Oetiker 1098 or equivalent (C). Slide the rack right and left to be certain that the boots are not deformed or twisted.
    Fig 61: Closing Ear Portion Of Band Using Commercially Available Pincers Or Oetiker 1098
    G03679026Courtesy of AMERICAN HONDA MOTOR CO., INC.
  95. Install a new lock washer (A) on the tie-rod (B) with the radius side of the washer toward the tie-rod, and screw the tie-rod into the bracket (C). Repeat this step for the other tie-rod. Hold the bracket with one wrench, and tighten both tie-rods to the specified torque with another wrench.
    Fig 62: Installing New Lock Washer On Tie-Rod And Torque Specifications
    G03679027Courtesy of AMERICAN HONDA MOTOR CO., INC.
  96. Bend the lock washers (A) against the flat spots on the bracket with a large pair of pliers.
    Fig 63: Bending Lock Washers
    G03679028Courtesy of AMERICAN HONDA MOTOR CO., INC.
  97. Install the cylinder lines (A) and return line joint (B).

    Note these items during reassembly:

    • Thoroughly clean the joints of the cylinder lines. The joints must be free of foreign material.
    • Install the cylinder lines by tightening the flare nuts by hand first, then tighten the flare nuts to the specified torque.
    Fig 64: Installing Cylinder Lines And Tightening Flare Nuts To The Specified Torque
    G03679029Courtesy of AMERICAN HONDA MOTOR CO., INC.
  98. Adjust the rack guide screw (see RACK GUIDE ADJUSTMENT ). After adjusting, check that the rack moves smoothly by sliding it right and left.
  99. Install the steering gearbox (see STEERING GEARBOX INSTALLATION ).