LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2003 >> Element DX, 2.4 YH1, Standard >> Repair and Diagnosis >> Heating, Ventilation & A/C (HVAC) >> HVAC Control Systems >> Heating/Air Conditioning >> Heater Unit/Core Replacement

Heater Unit/Core Replacement

SRS components are located in this area. Review the SRS component locations (see COMPONENT LOCATION INDEX ), and precautions and procedures (see PRECAUTIONS AND PROCEDURES ) before performing repairs or service.

  1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the radio's preset buttons.
  2. Disconnect the negative cable from the battery.
  3. With air conditioning; disconnect the A/C lines from the evaporator core (see EVAPORATOR CORE REPLACEMENT ).
  4. From under the hood, open the cable clamp (A), then disconnect the heater valve cable (B) from the heater valve arm (C). Turn the heater valve arm to the fully opened position as shown.
    Fig 1: Disconnecting Heater Valve Cable From Heater Valve Arm
    G03679645Courtesy of AMERICAN HONDA MOTOR CO., INC.
  5. When the engine is cool, drain the engine coolant from the radiator (see COOLANT CHECK ).
  6. Slide the hose clamps (A) back, then disconnect the inlet heater hose (B) and the outlet heater hose (C) from the heater core. Engine coolant will run out when the hoses are disconnected; drain it into a clean drip pan. Be sure not to let engine coolant spill on the electrical parts or the painted surfaces. If any coolant spills, rinse it off immediately.
    Fig 2: Disconnecting Inlet Heater Hose And Outlet Heater Hose From Heater Core
    G03679646Courtesy of AMERICAN HONDA MOTOR CO., INC.
  7. Remove the mounting bolt and the heater valve as shown. Remove the mounting nut from the heater unit. Take care not to damage or bend the fuel lines and the brake lines, etc.
    Fig 3: Removing Mounting Bolt And Torque Specifications
    G03679647Courtesy of AMERICAN HONDA MOTOR CO., INC.
  8. Remove the dashboard (see DASHBOARD REMOVAL/INSTALLATION ).
  9. Remove the ECM/PCM (see ECM/PCM REPLACEMENT ).
  10. Disconnect the connectors (A) from the dashboard wire harness, the air mix control motor, the evaporator temperature sensor, the power transistor, the mode control motor, the blower motor, and the recirculation control motor, then remove the wire harness clips (B), the connector clips (C), the wire harness (D), the heater duct (E), and the clip (F). Disconnect the drain hose (G), then remove the mounting nuts and the blower-heater unit (H).
    Fig 4: Disconnecting Connectors From Dashboard Wire Harness, Air Mix Control Motor, Evaporator Temperature Sensor, Power Transistor, Mode Control Motor, Blower Motor And Recirculation Control Motor With Specified Torques
    G03679648Courtesy of AMERICAN HONDA MOTOR CO., INC.
  11. Remove the self-tapping screws and the expansion valve cover (A). With air conditioning; carefully pull out the evaporator core (with A/C) (B) so you don't bend the inlet and outlet pipes. Remove the self-tapping screws and the flange cover (C), then remove the grommet (D), and carefully pull out the heater core (E) so you don't bend the inlet and outlet pipes.
    Fig 5: Removing Self-Tapping Screws And Expansion Valve Cover
    G03679649Courtesy of AMERICAN HONDA MOTOR CO., INC.
  12. Install the heater core and the evaporator core (with A/C) in the reverse order of removal.
  13. Install the heater unit in the reverse order of removal, and note these items:
    • Do not interchange the inlet and outlet heater hoses, and install the hose clamps securely.
    • Refill the cooling system with engine coolant (see COOLANT CHECK ).
    • Be sure to connect the drain hose securely.
    • Adjust the heater valve cable (see HEATER VALVE CABLE ADJUSTMENT ).
    • Make sure that there is no engine coolant leakage.
    • Make sure that there is no air leakage.
    • With air conditioning, refer to evaporator core replacement (see EVAPORATOR CORE REPLACEMENT ).
    • Enter the anti-theft codes for the radio, then enter the audio presets.