LEMON Manuals: Even more car manuals for everyone
Home >> Honda >> 2003 >> Element DX, 2.4 YH1, Standard >> Repair and Diagnosis >> Engine Performance >> System >> PGM-FI System >> DTC Troubleshooting >> DTC P0335: CKP Sensor No Signal

DTC P0335: CKP Sensor No Signal

NOTE: Before you troubleshoot, record all freeze data and any on-board snapshot, and review the general troubleshooting information (see GENERAL TROUBLESHOOTING INFORMATION ).
  1. Turn the ignition switch ON (II).
  2. Clear the DTC with the HDS.
  3. Start the engine.
  4. Check for Temporary DTCs or DTCs with the HDS.

    Is DTC P0335 indicated? 

    1. YES-  Go to step  5.
    2. NO-  Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the CKP sensor and the ECM/PCM.
  5. Turn the ignition switch OFF.
  6. Disconnect the CKP sensor 3P connector.
  7. Turn the ignition switch ON (II).
  8. Measure voltage between CKP sensor 3P connector terminal No. 1 and body ground.
    Fig 1: Measuring Voltage Between CKP Sensor 3P Connector Terminal And Body Ground
    G03677566Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    1. YES-  Go to step  9.
    2. NO-  Repair open in the wire between the CKP sensor and PGM-FI main relay 1 (FI MAIN), then go to step  18.
  9. Measure voltage between CKP sensor 3P connector terminal No. 2 and body ground.
    Fig 2: Measuring Voltage Between CKP Sensor 3P Connector Terminal And Body Ground
    G03677567Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there about 5 V? 

    1. YES-  Go to step  10.
    2. NO-  Go to step  11.
  10. Measure voltage between CKP sensor 3P connector terminals No. 1 and No. 3.
    Fig 3: Measuring Voltage Between CKP Sensor 3P Connector Terminals
    G03677568Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there battery voltage? 

    1. YES-  Go to step  16.
    2. NO-  Repair open in the wire between the CKP sensor and G101, then go to step  18.
  11. Measure voltage between ECM/PCM connector terminal A7 and body ground.
    Fig 4: Measuring Voltage Between ECM/PCM Connector Terminal A7 And Body Ground
    G03677569Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there about 5 V? 

    1. YES-  Repair open in the wire between the ECM/PCM (A7) and the CKP sensor, then go to step  18.
    2. NO-  Go to step  12.
  12. Turn the ignition switch OFF.
  13. Jump the SCS line with the HDS.
  14. Disconnect ECM/PCM connector A (31P).
  15. Check for continuity between ECM/PCM connector terminal A7 and body ground.
    Fig 5: Checking Continuity Between ECM/PCM Connector Terminal A7 And Body Ground
    G03677570Courtesy of AMERICAN HONDA MOTOR CO., INC.

    Is there continuity? 

    1. YES-  Repair short in the wire between the ECM/PCM (A7) and the CKP sensor, then go to step  18.
    2. NO-  Go to step  25.
  16. Turn the ignition switch OFF.
  17. Replace the CKP sensor (see CKP SENSOR REPLACEMENT ).
  18. Reconnect all connectors.
  19. Turn the ignition switch ON (II).
  20. Reset the ECM/PCM with the HDS.
  21. Clear the CKP pattern with the HDS.
  22. Do the ECM/PCM idle learn procedure (see ECM/PCM IDLE LEARN PROCEDURE ).
  23. Do the CKP pattern learn procedure (see CRANK (CKP) PATTERN CLEAR/CRANK (CKP) PATTERN ).
  24. Check for Temporary DTCs or DTCs with the HDS.

    Are any Temporary DTCs or DTCs indicated? 

    1. YES-  If DTC P0335 is indicated, check for poor connections or loose terminals at the CKP sensor and the ECM/PCM, then go to step  1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting .
    2. NO-  Troubleshooting is complete.
  25. Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM (see ECM/PCM UPDATING AND SUBSTITUTION FOR TESTING ).
  26. Check for Temporary DTCs or DTCs with the HDS.

    Are any Temporary DTCs or DTCs indicated? 

    1. YES-  If DTC P0335 is indicated, check for poor connections or loose terminals at the CKP sensor and the ECM/PCM, then go to step  1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting .
    2. NO-  If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was substituted, replace the original ECM/PCM (see MAP SENSOR REPLACEMENT ).