LEMON Manuals: Even more car manuals for everyone
Home >> GMC >> 2021 >> Yukon AT4 >> Repair and Diagnosis >> Steering >> Steering Column >> Steering Wheel And Column >> Repair Instructions >> Steering Column Tilt Wheel and Telescope Control Module Replacement (with Denali) >> Removal Procedure

Removal Procedure

  1. Disable the SIR system. SIR Disabling and Enabling
  2. GM5515686Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Lower Trim Panel Outer Filler (1) - Remove

  3. GM5596335Courtesy of GENERAL MOTORS COMPANY

    Using a flat-bladed plastic trim tool, release the retaining clips.

  4. Instrument Panel Fuse Block Access Hole Cover (1) - Remove
  5. GM5596337Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Trim Pad Bolt (1) - Remove

  6. Disconnect the electrical connectors.
  7. Instrument Panel Trim Pad (2) - Remove
  8. GM5596403Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Switch Trim Plate Bolt (1) - Remove

  9. Disconnect the electrical connectors.
  10. Instrument Panel Switch Trim Plate (2) - Remove
  11. GM5517088Courtesy of GENERAL MOTORS COMPANY

    Hood Primary Latch Release Cable Handle (1) - Release

  12. Instrument Panel Knee Bolster Bolt (2) - Remove [ 2x ]
  13. GM5515684Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Lower Insulator Retainer (1) - Remove [ 2x ]

  14. GM5515685Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Lower Trim Panel Insulator (1) - Remove

  15. GM5562885Courtesy of GENERAL MOTORS COMPANY

    Release the retaining tab.

  16. Rotate the front floor courtesy lamp (1) a quarter turn counterclockwise to release.
  17. GM5562886Courtesy of GENERAL MOTORS COMPANY

    Front Floor Courtesy Lamp (1) - Remove

  18. Disconnect the electrical connector.
  19. GM5517090Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    You may have to push down on the lower steering column closeout to clear the instrument panel cluster trim plate.

    Instrument Panel Knee Bolster (1) - Remove

  20. Extend the steering column to its furthest point to allow the instrument panel steering column upper trim cover to clear the instrument panel.
  21. GM5598929Courtesy of GENERAL MOTORS COMPANY

    Using a small plastic trim tool, separate the instrument panel steering column upper trim cover (1) from the instrument panel steering column lower trim cover.

  22. GM5527242Courtesy of GENERAL MOTORS COMPANY

    Using a small plastic trim tool, separate the instrument panel steering column upper trim cover (1) from the instrument panel steering column opening closeout (2).

  23. GM5598934Courtesy of GENERAL MOTORS COMPANY

    Turn the steering wheel approximately 90 degrees to the left of the centered position.

  24. Instrument Panel Steering Column Lower Trim Cover Bolt (1) - Remove
  25. GM5598947Courtesy of GENERAL MOTORS COMPANY

    Turn the steering wheel approximately 90 degrees to the right of the centered position.

  26. Instrument Panel Steering Column Lower Trim Cover Bolt (1) - Remove
  27. Turn the steering wheel to the centered position.
  28. GM5598936Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Steering Column Lower Trim Cover Bolt (1) - Remove

  29. GM5598937Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Steering Column Lower Trim Cover (1) - Remove

  30. Disconnect the electrical connectors.
  31. CAUTION:

    With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column lock, or a strap to prevent rotation. Locking of the steering column will prevent damage and a possible malfunction of the SIR system. The steering wheel must be secured in position before disconnecting the following components:

    • The steering column
    • The intermediate shaft(s)
    • The steering gear

    After disconnecting these components, do not rotate the steering wheel or move the front tires and wheels. Failure to follow this procedure may cause the SIR coil assembly to become un-centered and cause possible damage to the SIR coil. If you think the SIR coil has became un-centered, refer to your specific SIR coil's centering procedure to re-center SIR Coil.

  32. Install an appropriate device to prevent the steering column from rotating.
  33. GM5519904Courtesy of GENERAL MOTORS COMPANY

    Floor Front Air Outlet Duct Bolt (1) - Remove

  34. GM5519906Courtesy of GENERAL MOTORS COMPANY

    Floor Front Air Outlet Duct - Left Side (1) - Remove

  35. GM5519907Courtesy of GENERAL MOTORS COMPANY

    Upper Intermediate Steering Shaft Bolt (1) - Remove

  36. GM5519908Courtesy of GENERAL MOTORS COMPANY

    Upper Intermediate Steering Shaft (1) @ Steering Column (2) - Separate

  37. GM5596440Courtesy of GENERAL MOTORS COMPANY

    Steering Column Nut (1) - Remove [ 4x ]

  38. Disconnect the steering column electrical connectors as necessary.
  39. GM5628121Courtesy of GENERAL MOTORS COMPANY

    Steering Column (1) - Remove

  40. GM5551463Courtesy of GENERAL MOTORS COMPANY

    Disconnect the electrical connectors. (1)

  41. Steering Column Control Module Bracket Bolt (2) - Remove [ 2x ]
  42. Steering Column Tilt Wheel and Telescope Control Module (3) - Remove